Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
This allows boards to fixup / overwrite DT model string when booting OS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Michal Simek <michal.simek@amd.com> says:
I looked as cleaning up some dependencies and I found that qconfig is
reporting some issues. This series is fixing some of them. But there are
still some other pending. That's why please go and fix them if they are
related to your board.
UTF-8: I am using uni2ascii -B < file to do conversion. When you run it in
a loop you will find some other issue with copyright chars or some issues
in files taken from the Linux kernel like DTs. They should be likely fixed
in the kernel first.
Based on discussion I am ignoring names too.
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
The following information printed on every boot is not very
helpful for the users:
SOC: 0xa0009300
LC: 0x40040
Move them to debug() level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mathieu Othacehe <othacehe@gnu.org>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() and setup_fec() functions anymore.
Remove them.
Successfully tested a TFTP transfer after these changes.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add a weak default reset_cpu() implementation just like
it is done on arch/arm/mach-imx/cpu.c.
This allows the removal of the empty reset_cpu() in several
board files.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
Generally speaking, we do not prompt for this value and define it in the
board specific Kconfig file. There are some valid use cases however
today where we do prompt for this value, so instead of having this be
done in a number of locations, do this at the top-level location only.
This removes the question from a number of other locations and makes it
consistent that when we do set the value directly, we always do it the
same way. We don't need to specify the type, it's always string.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for booting the imxrt1050-evk from spi.
Add imximage config and the ability for SPL to boot from NOR.
Enable binman in Kconfig and device tree for imxrt* as it is used to
prepend fspi_header.bin to SPL and u-boot.img.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Put imx9_probe_mu declaration in a new mu.h header file.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() anymore.
Remove it.
Confirmed that TFTP transfer still works fine without board_phy_config().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arm including config.h directly, but
add it where needed. This includes a few board-specific fixes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
The U_BOOT_CMD_COMPLETE() macro has a semicolon at the end, perhaps
inadvertently. Some code has taken advantage of this.
Tidy this up by dropping the semicolon from the macro and adding it to
macro invocations as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
The RTL8211FDI Ethernet PHYs have 25MHz oscillator, so there is no
need to enable the RGMII TX clk output.
Also, there is no need for describing the deprecated phy-reset FEC
properties, nor passing reset properties to the EQOS interface in
u-boot.dtsi.
Remove all these unneeded pieces.
Tested both Ethernet interfaces after these changes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
I would like to help maintaining the imx8mp_evk board.
Add myself to MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Commit 0aea5dda2928 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
As we call sprintf in this file we need to include vsprintf.h in order
to get the function prototype and we need linux/string.h for strcmp.
Signed-off-by: Tom Rini <trini@konsulko.com>
As we call sprintf in this file we need to include vsprintf.h in order
to get the function prototype and we need linux/string.h for strcmp.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_LONGHELP=n we want to reduce the size of the U-Boot binary.
The long text should be reduced to and empty string in this case.
There is not need to call cmd_usage() directly. It is sufficient to
return CMD_RET_USAGE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Board specific implementations of the 'mac' command differ concerning the
supported sub-commands.
Move the Freescale specific mac command definition to the board code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use the misc_init_f event instead, which is designed for this purpose.
All boards with CONFIG_VID already enable CONFIG_EVENT.
Signed-off-by: Simon Glass <sjg@chromium.org>
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1f1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As the defconfig files here have been removed we can also remove the
entries.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rajesh's email bounces. Remove his email from all boards he maintains.
Fortunately, he has co-maintainers on most boards. I have taken the
liberty of volunteering Pramod to maintain the LS1012AFRDM, since he
also maintains the LS1012AFRWY. Let me know if the board should be
orphaned instead.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add myself as a maintainer for orphaned boards.
All these boards are covered by buildman m68k test.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
In a few cases we have MAINTAINERS entries that are missing obvious
paths or files. Typically this means a board directory that did not list
itself, but in a few cases we have a Kconfig file or similar.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are a few entries where minor mistakes mean that we don't match up
with obviously expected files, correct those.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
