brcm,bcm2708-fb device provided by firmware on RPi5 uses
16 bits per pixel, so lets calculate framebuffer bytes
per pixel dynamically based on queried information.
Tested to work for RPi2b v1.2, RPi3b v1.3, RPi4b v1.1,
RPi2 Zero W, RPi5b v1.0.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Existing gpio-gate-clock driver acts like a simple GPIO switch without any
effect on gated clock. Add actual clock actions into enable/disable ops and
implement get_rate op by passing gated clock if it is enabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20240110160956.4476-2-clamor95@gmail.com
[ sorted includes ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When we call clk_get_rate(), we expect to get clock rate value as
ulong.
In that case we should not use log_ret() macro since it use internally
an int.
Otherwise we may return an invalid/truncated clock rate value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Fixes: 5c5992cb90c ("clk: Add debugging for return values")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/87o7erv9p4.fsf@baylibre.com
Amlogic SoCs embeds an hardware clock measure block, port it
from Linux and implement it as a UCLK_CLK with only the dump
op and fail-only xlate.
Based on the Linux driver introduced in [1].
[1] commit 2b45ebef39a2 ("soc: amlogic: Add Meson Clock Measure driver").
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231218-uboot-meson-clk-msr-v3-1-acf4d90ccfee@linaro.org
Without explicit support for VIDEO_X2R10G10B10 VIDEO_X8R8G8B8 white
will be rendered as cyan-ish. The conversion leaves to lowest 2 bits
unset for more compact code.
Signed-off-by: Janne Grunau <j@jannau.net>
Use device-tree node property names for parsing nodes instead of
indexing as indexing could be different between different SoCs based on
number of DSS entities available on that particular SoC.
Also correct the video layer naming in driver to match to actual one
being used in upstream DSS device-tree node [1].
This also fixes AM62x splash screen usage using the latest upstream DSS
device-tree nodes where hard-coded indexing which driver was using
before this patch was not matching the correct properties in the DT
node.
[1]: Upstream AM62x DSS node:
https://github.com/torvalds/linux/blob/v6.8-rc1/arch/arm64/boot/dts/ti/k3-am62-main.dtsi#L774
Fixes: 5f9f816bb8 ("drivers: video: tidss: TIDSS video driver support for AM62x")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Devarsh Thakkar <devarsht@ti.com> says:
Move video memory reservation for SPL at end of RAM so that it does
not interefere with reservations for next stage so that the next stage
need not have holes in between for passed regions and instead it can
maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same
problem.
While at it, also fill missing fields in video handoff struct before
passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
https://lore.kernel.org/all/CAPnjgZ3xSoe_G3yrqwuAvoiVjUfZ+YQgkOR0ZTVXGT9VK8TwJg@mail.gmail.com/
For filling missing video handoff fields :
https://lore.kernel.org/all/CAPnjgZ1Hs0rNf0JDirp6YPsOQ5=QqQSP9g9qRwLoOASUV8a4cw@mail.gmail.com/
Fill video handoff fields in video_post_probe as at this point we have
full framebuffer-related information.
Also fill all the fields available in video hand-off struct as those
were missing earlier and U-boot framework expects them to be filled for
some of the functionalities.
While filling framebuffer size in video hand-off structure use the
actual framebuffer region size as derived from gd->video_top and
gd->video_bottom instead of directly using the size populated in
video_uc_plat as it contains unaligned size.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip framebufer reservation if it was already reserved from previous
stage and whose information was passed using a bloblist.
Return error in case framebuffer information received from bloblist is
invalid i.e NULL or empty.
While at it, improve the debug message to make it more clear that
address in discussion is of framebuffer and not bloblist and also match
it with printing scheme followed in video_reserve function.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_mdp_ready() handles status polling for multi-die package parts that
requires to read and check status register for each die. To support
S28HS02GT(dual-die package with Octal DTR support), rename function and
use nor->rdsr_dummy in octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation encounters issues when testing data ranging
from 0 to 8 bytes. This was confirmed through testing with both ISSI
(IS25WX256) and Micron (MT35XU02G) Flash exclusively in SDR mode.
Upon investigation, it was observed that utilizing the
"SPI_NOR_OCTAL_READ" flag and attempting to read less than 8 bytes in
STIG mode results in a read failure, leading to a compare test failure.
To resolve this issue, the CMD_4BYTE_FAST_READ opcode is now utilized
instead of CMD_4BYTE_OCTAL_READ, specifically in SDR mode.
This is based on patch series:
https://lore.kernel.org/all/cover.1701853668.git.tejas.arvind.bhumkar@amd.com/
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If even one byte is lost due to Rx FIFO overflow then we will never
exit the read loop. Because the (priv->rx != priv->rx_end) condition will
be always true.
Let's check if Rx FIFO overflow occurred and exit the read loop
in this case.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The current code convert the SMBIOS 2.1 entry point structure to
SMBIOS 3.0 entry point structure. The max_struct_size member in
SMBIOS 2.1 entry point structure indicates
"Size of the largest SMBIOS structure, in bytes".
We need to use struct_table_length instead.
Fixes: 1c5aab803c0b ("smbios: copy QEMU tables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable serial support for Exynos850 SoC by adding the corresponding
compatible string. No additional changes needed, the driver works as is
on Exynos850. Related USI and PMU configuration is enabled in separate
drivers. The only other dependencies are clock and pinctrl drivers,
which are already enabled too.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add pinctrl support for Exynos850 SoC. It was mostly extracted from
corresponding Linux kernel code [1]. Power down modes and external
interrupt data were removed while converting the code for U-Boot, but
everything else was kept almost unchanged.
[1] drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heavily influenced by its Linux kernel counterpart. It's implemented on
top of recently added Samsung CCF clock framework API. For now only UART
leaf clocks are implemented, along with all preceding clocks in CMU_TOP
and CMU_PERI. The UART baud clock is required in the serial driver, to
get its rate for the consequent baud rate calculation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heavily based on Linux kernel Samsung clock framework, with some changes
to accommodate the differences in U-Boot CCF implementation. It's also
quite minimal as compared to the Linux version.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PLL utilities code is only used by clk-exynos7420 driver at the moment.
Move it into clk-exynos7420 to make clk-pll.c file available for CCF PLL
clocks implementation, which is coming in the next patches.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add basic Power Management Unit (PMU) driver for Exynos SoCs. For now
it's only capable of changing UART path in PMU, which is needed for
E850-96 board. The driver's structure resembles the exynos-pmu driver
from Linux kernel, and although it's very basic and slim at the moment,
it can be easily extended in future if the need arises.
UCLASS_NOP is used, as there are no benefits in using more elaborate
classes like UCLASS_MISC in this case. The DM_FLAG_PROBE_AFTER_BIND flag
is added in bind function, as the probe function must be always called
for this driver.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
USIv2 IP-core is found on modern ARM64 Exynos SoCs (like Exynos850) and
provides selectable serial protocol (one of: UART, SPI, I2C). USIv2
registers usually reside in the same register map as a particular
underlying protocol it implements, but have some particular offset. E.g.
on Exynos850 the USI_UART has 0x13820000 base address, where UART
registers have 0x00..0x40 offsets, and USI registers have 0xc0..0xdc
offsets. Desired protocol can be chosen via SW_CONF register from System
Register block of the same domain as USI.
Before starting to use a particular protocol, USIv2 must be configured
properly:
1. Select protocol to be used via System Register
2. Clear "reset" flag in USI_CON
3. Configure HWACG behavior (e.g. for UART Rx the HWACG must be
disabled, so that the IP clock is not gated automatically); this is
done using USI_OPTION register
4. Keep both USI clocks (PCLK and IPCLK) running during USI registers
modification
This driver implements the above behavior. Of course, USIv2 driver
should be probed before UART/I2C/SPI drivers. It can be achieved by
embedding UART/I2C/SPI nodes inside of the USI node (in Device Tree);
driver then walks underlying nodes and instantiates those. Driver also
handles USI configuration on PM resume, as register contents can be lost
during CPU suspend.
This driver is designed with different USI versions in mind. So it
should be relatively easy to add new USI revisions to it later.
Driver's code was copied over from Linux kernel [1] and adapted
correspondingly for U-Boot API. UCLASS_MISC is used, and although no
misc operations are implemented, it makes it easier to probe the driver
this way (as compared to UCLASS_NOP) and keep the code compact.
[1] drivers/soc/samsung/exynos-usi.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
MEMCLKMGR_EXTCNTRST_C0CNTRST register defined as BIT[0] in documentation
but it is wrongly defined as BIT[7] in u-boot code. This register is used
to hold associated pingpong counter in reset
while PLL and 5:1 mux configuration is changed.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
These removed definitions were specific to some sam9 SoCs, but not
generic over all at91 SoCs. The correct SoC specific definitions for
ATMEL_BASE_PMECC are spread over different header files in
arch/arm/mach-at91/include/mach directory.
Fixes a build error on a custon board based on SAMA5D2:
Building current source for 73 boards (16 threads, 1 job per thread)
arm: + vera2
+drivers/mtd/nand/raw/atmel/pmecc.c:819: warning: "ATMEL_BASE_PMECC" redefined
+ 819 | #define ATMEL_BASE_PMECC 0xffffe000
+ |
+In file included from include/configs/vera2.h:11,
+ from include/config.h:3,
+ from include/linux/mtd/rawnand.h:16,
+ from drivers/mtd/nand/raw/atmel/pmecc.c:44:
+include/asm/arch/sama5d2.h:171: note: this is the location of the previous definition
+ 171 | #define ATMEL_BASE_PMECC (ATMEL_BASE_HSMC + 0x70)
+drivers/mtd/nand/raw/atmel/pmecc.c:820: warning: "ATMEL_BASE_PMERRLOC" redefined
+ 820 | #define ATMEL_BASE_PMERRLOC 0xffffe600
+include/asm/arch/sama5d2.h:172: note: this is the location of the previous definition
+ 172 | #define ATMEL_BASE_PMERRLOC (ATMEL_BASE_HSMC + 0x500)
Fixes: a490e1b7c017 ("nand: atmel: Add pmecc driver")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
-----BEGIN PGP SIGNATURE-----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=BoSU
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20240119' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add CMDLINE dependecy for CMD_STM32KEY
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
- A number of OS boot related cleanups, a number of TI platform
fixes/cleanups, SMBIOS fixes, tweak get_maintainers.pl to report me
for more places, fix the "clean the build" pytest and add a bootstage
pytest, fix PKCS11 URI being omitted in some valid cases, make an iommu
problem easier to debug on new platforms, nvme and pci improvements,
refactor image-host code a bit, fix a typo in env setting, add a missing
dependency for CMD_LICENSE, and correct how we call getchar() in some
places.
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A busy controller shouldn't be game-over for all controllers,
so keep trying on hitting -EBUSY.
This change brings the actual behavior of the routine in line
with what the descriptions says.
Fixes: 982388eaa991 ("nvme: Add NVM Express driver support")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
