Nothing really major here, some rework of the SPL PMIC drivers, adding
support for the AXP717 on the way, which is showing up on newer boards
now, most prominently some Anbernic handheld gaming devices. The rest
is enabling Ethernet and SPI boot on the Allwinner V3s SoC, plus two
fixes. This also updates the "traditional U-Boot" DTs to that of kernel
v6.9. I will look into upgrading some SoCs to dts/upstream in the
coming cycle, though this will not cover all SoCs for now, as we carry
some non-mainline fix to improve compatibility with older kernels. Will
see how it goes, but for now we stick with the "old way".
The branch survived the gitlab CI run, and Linux boot testing on some
selected boards.
The BootROM in the Allwinner H616 tries to load the initial boot code
from sector 16 (8KB) of an SD card or eMMC device, but also looks at
sector 512 (256KB). This helps with GPT formatted cards.
A "high" boot offset is also used on previous SoCs, but it's sector 256
(128KB) there instead.
Extend the existing offset calculation code to consider the different
sector offset when running on an H616 SoC. This allows to load U-Boot
on any H616 device when the SPL is not located at 8KB.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
The V3s is identical regarding register layout, clocks and resets to
the sun6i variants. Therefore, we can just add the MACH_SUN8I_V3S to
the sun6i compatible ones.
SPI boot was tested on a custom board with a Gigadevice GD25Q64 8MiB
SPI flash.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.9.
This is covering Allwinner SoCs with 32-bit and 64-bit ARM cores.
Besides some cosmectic changes, this adds S/PDIF, DMA, and thermal
support to the H616 .dtsi. Nothing that U-Boot needs for itself, but
helpful to pass on to kernels.
This also adds new devicetrees, for some LonganPi H616 board, and the
Remix Mini PC. The latter will get a defconfig next.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On boards using the AXP717 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Using the new generic AXP SPL driver, add the Kconfig options and
platform bits needed to support an AXP717 PMIC chip in I2C mode.
This allows to set up the correct voltage for the DRAM chips and the
CPU cores.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE in DS116 defconfig. Remove current DTS in
arch/arm/dts/ directory.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't set many options in the board Kconfig entry file but instead
use defconfigs, select in some cases on the target itself, or update the
"default" options of the main entries when needed. In this case we can
remove most of the board Kconfig entries and just add them to the
defconfig like other platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use the CONFIG_IS_ENABLED() macro when checking for DM_SERIAL so that
CFG_SYS_NS16550_CLK is not defined as get_serial_clock() in SPL if SPL
does not have DM_SERIAL enabled.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use CONFIG_VAL() for SYS_MONITOR_BASE in start.S so that correct value
is used for SPL.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
The find_law() function searches for LAW just by physical address. This
is unsuitable for cases with overlapping LAWs. Extend it to
find_law_by_addr_id(), which searches for LAW by physical address and
target id.
Add a static inline definition of the original find_law() into fsl_law.h
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
This empty stub was originally added as one branch of an #ifdef in
commit 45a6d231b2f (bcm2835_wdt: support for the BCM2835/2836
watchdog). That incarnation of the rpi watchdog driver was later
removed in c7adc0b5f98 (watchdog: bcm2835_wdt: Remove unused BCM283x
watchdog driver and its references), but this now unused stub was left
behind. The later (re-)added rpi watchdog driver does not define a
hw_watchdog_disable() function, as that is properly integrated in the
watchdog framework.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This reverts commit 33041972727e84d3f95e26c83322521f61827584.
With the ability to generate this SMBIOS details autmotically the
small amount of details that this patch provided are generated
automatically so this is now obsolete so we can just drop it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
Support old DDR3 training code on Turris Omnia, selectable via EEPROM
field.
Users experiencing DDR3 initialization failures or random crashes of the
operating system due to incorrect DDR3 configuration can select the old
DDR3 training implementation to fix those issues by setting the EEPROM
field "Use old DDR training":
eeprom update "Use old DDR training" 1
Signed-off-by: Marek Behún <kabel@kernel.org>
Add optional support for using old DDR3 training code from 2017.
The code lives in drivers/ddr/marvell/a38x/old/. To prevent symbol
clashing with new DDR3 training code, a special header which renames all
clashing symbols via macros is included and the symbols are prefixed
with 'old_'.
If old DDR3 training support is selected for a board, then the SPL
initialization code calls a new function
board_use_old_ddr3_training()
to check whether it should use old DDR3 training code. The default
weak implementation returns false, defaulting to new DDR3 training code.
Boards that wish to support this need to select the
ARMADA_38X_SUPPORT_OLD_DDR3_TRAINING
config option and implement the old version of DDR topology provider,
ddr3_get_topology_map().
Signed-off-by: Marek Behún <kabel@kernel.org>
