Nothing really major here, some rework of the SPL PMIC drivers, adding
support for the AXP717 on the way, which is showing up on newer boards
now, most prominently some Anbernic handheld gaming devices. The rest
is enabling Ethernet and SPI boot on the Allwinner V3s SoC, plus two
fixes. This also updates the "traditional U-Boot" DTs to that of kernel
v6.9. I will look into upgrading some SoCs to dts/upstream in the
coming cycle, though this will not cover all SoCs for now, as we carry
some non-mainline fix to improve compatibility with older kernels. Will
see how it goes, but for now we stick with the "old way".
The branch survived the gitlab CI run, and Linux boot testing on some
selected boards.
The BootROM in the Allwinner H616 tries to load the initial boot code
from sector 16 (8KB) of an SD card or eMMC device, but also looks at
sector 512 (256KB). This helps with GPT formatted cards.
A "high" boot offset is also used on previous SoCs, but it's sector 256
(128KB) there instead.
Extend the existing offset calculation code to consider the different
sector offset when running on an H616 SoC. This allows to load U-Boot
on any H616 device when the SPL is not located at 8KB.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
The V3s is identical regarding register layout, clocks and resets to
the sun6i variants. Therefore, we can just add the MACH_SUN8I_V3S to
the sun6i compatible ones.
SPI boot was tested on a custom board with a Gigadevice GD25Q64 8MiB
SPI flash.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.9.
This is covering Allwinner SoCs with 32-bit and 64-bit ARM cores.
Besides some cosmectic changes, this adds S/PDIF, DMA, and thermal
support to the H616 .dtsi. Nothing that U-Boot needs for itself, but
helpful to pass on to kernels.
This also adds new devicetrees, for some LonganPi H616 board, and the
Remix Mini PC. The latter will get a defconfig next.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On boards using the AXP717 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Using the new generic AXP SPL driver, add the Kconfig options and
platform bits needed to support an AXP717 PMIC chip in I2C mode.
This allows to set up the correct voltage for the DRAM chips and the
CPU cores.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE in DS116 defconfig. Remove current DTS in
arch/arm/dts/ directory.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This empty stub was originally added as one branch of an #ifdef in
commit 45a6d231b2f (bcm2835_wdt: support for the BCM2835/2836
watchdog). That incarnation of the rpi watchdog driver was later
removed in c7adc0b5f98 (watchdog: bcm2835_wdt: Remove unused BCM283x
watchdog driver and its references), but this now unused stub was left
behind. The later (re-)added rpi watchdog driver does not define a
hw_watchdog_disable() function, as that is properly integrated in the
watchdog framework.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This reverts commit 33041972727e84d3f95e26c83322521f61827584.
With the ability to generate this SMBIOS details autmotically the
small amount of details that this patch provided are generated
automatically so this is now obsolete so we can just drop it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
Support old DDR3 training code on Turris Omnia, selectable via EEPROM
field.
Users experiencing DDR3 initialization failures or random crashes of the
operating system due to incorrect DDR3 configuration can select the old
DDR3 training implementation to fix those issues by setting the EEPROM
field "Use old DDR training":
eeprom update "Use old DDR training" 1
Signed-off-by: Marek Behún <kabel@kernel.org>
Add optional support for using old DDR3 training code from 2017.
The code lives in drivers/ddr/marvell/a38x/old/. To prevent symbol
clashing with new DDR3 training code, a special header which renames all
clashing symbols via macros is included and the symbols are prefixed
with 'old_'.
If old DDR3 training support is selected for a board, then the SPL
initialization code calls a new function
board_use_old_ddr3_training()
to check whether it should use old DDR3 training code. The default
weak implementation returns false, defaulting to new DDR3 training code.
Boards that wish to support this need to select the
ARMADA_38X_SUPPORT_OLD_DDR3_TRAINING
config option and implement the old version of DDR topology provider,
ddr3_get_topology_map().
Signed-off-by: Marek Behún <kabel@kernel.org>
Allow compiling with immutable debug settings:
- DEBUG_LEVEL is always set to DEBUG_LEVEL_ERROR
- register dumps are disabled
This can save around 10 KiB of space in the resulting binary, which is a
lot in U-Boot SPL.
Signed-off-by: Marek Behún <kabel@kernel.org>
- Change the spi-max-frequency to 50000000 (50 Mhz). According to the
data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in
the DTS to ensure u-boot is consistent with what Linux kernel expected.
- Update GPIO fan to conform to the latest DT binding.
[1]
https://www.macronix.com/Lists/Datasheet/Attachments/8575/MX25L3205D,%203V,%2032Mb,%20v1.5.pdf
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The CONFIG_ENV_OFFSET is undefined if boot device is UART
(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART), or envs are not stored on flash
(CONFIG_ENV_IS_NOWHERE). Check for CONFIG_ENV_IS_IN_SPI_FLASH as the first
condition to determine whether env_sf_get_env_addr() should be provided.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Since commit ecb1c37a7b64 ("clk: imx8mp: Add EQoS MAC clock"),
the clocks for the DWMAC driver can be configured, and removing
them breaks operation.
Fixes: ecb1c37a7b64 ("clk: imx8mp: Add EQoS MAC clock")
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT and SoM rev.100 backward
compatibility DTO to cater for this change.
Since the MDIO address adjustment is now also in the rev.100 SoM DTO, not
only in the rev.100 PDK3 DTO, update Makefile accordingly as well, else the
DTC would complain about the DTO overriding the 'reg' property without also
updating the node unit-address, which is not doable without duplicating the
entire PHY node in the DTO, which leads to large amount of duplication with
no gain.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
In order to help setup pin configuration for special pins (UFS, SDCard),
introduce the msm_special_pin_data struct largely inspired from the
Linux conterpart but with only U-Boot required fields.
This struct is added to the pins_data to allow specifying the special
pins data for each SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
lets drop our downstream DTSI.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now that drivers are compatible enough with the upstream DTS, there is no
reason to not use the upstream DTS, so imply OF_UPSTREAM by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Provide basic DRAM info population from DT, cache setting and the
board_init stub.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The Lenovo IdeaPad Yoga 11 is a hybrid laptop/tablet Windows RT-based
computer released in late 2012. The device uses a 1.3 GHz quad-core
Nvidia Tegra 3 chipset with 2 GB of RAM, features a 11.6 inch 1366x768
screen and 32/64 GB of internal memory that can be supplemented with
a microSDXC card slot, full size SD card slot and 2 full size USB 2.0
ports.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Surface RT is a hybrid tablet computer developed and manufactured
by Microsoft and shipped with Windows RT. The tablet uses a 1.3 GHz
quad-core Nvidia Tegra 3 chipset with 2 GB of RAM, features 10.8
inch 1366x768 screen and 32/64 GB of internal memory that can be
supplemented with a microSDXC card giving up to 200 GB of
additional storage.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
WEXLER Tab 7t is a mini tablet computer developed by WEXLER that
runs the Android operating system. The device features a 7.0-inch
(180 mm) HD display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM,
8, 16 or 32 GB of storage that can be supplemented with a microSDXC
card giving up to 64 GB of additional storage and a full size USB
port.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Asus Eee Pad Transformer family are 2-in-1 detachable/slider
tablets developed by Asus that run the Android operating system.
The Eee Pad Transformers feature a 10.1-inch (260 mm) display,
an Nvidia Tegra 2 dual-core chip, 1 GB of RAM, and 16/32 GB of storage.
Transformers board derives from Nvidia Ventana development board.
This patch brings support for all 3 known T20 Transformers:
- Asus Eee Pad Transformer TF101
- Asus Eee Pad Transformer TF101G
- Asus Eee Pad Slider SL101
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This binary does not prevent the system from booting. Mark it optional
so that U-Boot can be built without it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
