Commit 0aea5dda2928 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The commit in linux kernel 81186dc16101 ("dt-bindings: zynqmp: add
destination mailbox compatible") make compatible string for child nodes
mandatory that's why add it.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-5-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The aliases and chosen nodes are currently indented using spaces.
Fix them to use the standard tab indentation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On branch WIP/17Oct2023, the EEPROM can no longer be read:
U-Boot 2023.10-latest (Oct 17 2023 - 15:53:43 -0400)
CPU: Freescale i.MX8MNano Quad rev1.0 at 1200 MHz
Reset cause: POR
Model: Variscite VAR-SOM-MX8MN Symphony evaluation board
var_read_som_eeprom: uclass_get_device_by_of_offset() failed: -19
initcall failed at call 000000004022207c (err=-19)
Convert EEPROM-related properties to bootph-all so that the EEPROM can
also be read outside of SPL.
Fixes: 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The memory maps for Apple's M2 Pro/Max/Ultra left MMIO space out which
was not used by any driver at the time. The display out exposed as
simple-framebuffer use a power-domain controlled by a device in an
unmapped region.
Add a map covering this region as well as another MMIO region in the
range 0x4'0000'0000 - 0x5'0000'0000. The added regions cover all MMIO
annotated in Apple's device tree in this range.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635ea4 ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable USB PHY nodes on ASUS Transformers, Grouper, Enadevoru
and LG X3. This is not mandatory since driver will use default
values but preferable for new devices.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Call regulators_enable_boot_on on board init to set all regulators
with boot-on property in device tree. If regulator is not used by
any device in the device tree but is essential for the device to
work a regression will occur.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Instead of duplicating the I2C3 node and adding NVEC specific
properties, reuse the I2C3 node, extend it with NVEC specific properties
and drop properties that are not needed by NVEC. This results in a DTB
that is a bit cleaner and avoids accidentally using I2C3 and NVEC which
would have them fight over the same hardware resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify spi and usb aliases name.
Add dt-binding for usb phy define and fix usb phy reset error.
Add tpm/otpee and host_intf node.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Reduce redundancy in code by using templates to generate the A72 boot
binaries (tispl.bin and u-boot.img) as well as R5 boot binary sysfw.itb
(for legacy boot following devices J721E and AM65x).
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add templates for FIT images used extensively across K3 boards with most
of the code common. This includes the FIT portions of:
- tispl.bin
- u-boot.img
- sysfw.itb (in case of legacy boot flow)
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
While at this enable the DM and TIFS UARTs for programming pinmux
since they are marked reserved by board.dts
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change spl_enable_dcache so it also enable icache on SPL
initialization for the main domain part of the boot flow. This
improves bootloader booting time.
Link: https://lore.kernel.org/all/20231109140958.1093235-1-joao.goncalves@toradex.com/
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Tested-by: Nishanth Menon <nm@ti.com>
k3-am62* SoC dtsi files now provide the following:
bootph-all: dmss secure_proxy_main dmsc k3_pds k3_clks k3_reset
main_pmx0 main_timer0 mcu_pmx0 wkup_conf chipid
bootph-pre-ram: secure_proxy_sa3 main_esm mcu_esm
Drop these from board r5 and u-boot.dtsi files as these are duplicate in
them now.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
BCDMA can be used at SPL for OSPI boot and mem-to-mem DMA
so add "bootph-all" to BCDMA node.
Suggested-by: Nishanth Menon <nm@ti.com>
Fixes: 9a3f2b6798b0 ("arm: dts: k3-am625-verdin-wifi-dev-u-boot.dtsi: Fix DMA/Ethernet")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual ARM Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
Baseline of the devicetree is from v6.6-rc1
https://beagleboard.org/ai-64https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the omap3 beagle to the beagle vendor folder representing
BeagleBoard.org platforms.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
With the upcoming folder separation, there is no further need to depend
on am625-binman.dtsi. Duplicate the existing definitions to u-boot.dtsi
and r5.dts as appropriate.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Commit 5019170970ad ("arch: arm: mach-k3: j721e: add support for UDA
FS") introduced basic UDA FS support, however, we can Take approach
similar to commit 0f1c1e8b368b ("arm: mach-k3: am625: Add support for
UDA FS"). While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
Signed-off-by: Nishanth Menon <nm@ti.com>
