Add Kconfig that enables FPGA reprogramming with warm boot on Arria 10.
This option allows to change the bitstream on the filesystem and apply
changes with warm reboot without the need for a power cycle.
Signed-off-by: Michał Barnaś <barnas@google.com>
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
The function uniphier_mem_map_init() is to change global variable
'mem_map', which is referenced to get_page_table_size() to calculate
the size of page table.
However, uniphier_mem_map_init() is called after get_page_table_size(),
so the size of page table and 'mem_map' become inconsist each other.
After all, U-Boot fails to boot on chip with memory map different from
default map,
uniphier_mem_map_init() should be moved to dram_init(), which is
called before get_page_table_size().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it is
booting from.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Relocate booindex to OCRAM region after it gets opened by TIFS so
the main domain bootloaders can have access to this data.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Add support for detecting and processing TIFSSTUB images for HS, HSFS
and GP devices.
TIFSSTUB image for related device type will be loaded, rest TIFSSTUB
images will be discarded.
Example, for GP device, tifsstub-gp will be loaded, tifsstub-hs and
tifsstub-fs will be discarded.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Move verdin-am62 to OF_UPSTREAM:
- handle the fact that dtbs now have a 'ti/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS file
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This extra binding is non-standard and now unneeded as we bind the
sysreset driver automatically. This matches what is done in Linux
and allows us to more closely match the DTBs. Remove the binding
and all users.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
During the boot, the EFI loader maps the memory from ram_top to ram_end
as EFI_BOOT_SERVICES_DATA. When LMB does boot_fdt_add_mem_rsv_regions()
to OPTEE, TFA, R5, and M4F DMA/memory "no-map" for the kernel it produces
the following error message:
ERROR: reserving fdt memory region failed (addr=9cb00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9cc00000 size=e00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9da00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9db00000 size=c00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e780000 size=80000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e800000 size=1800000 flags=4)
To avoid this, don't flag with EFI_BOOT_SERVICES_DATA the memory from
ram_top to ram_end by the EFI loader.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
The maximum frequency of the A53 CPU on the AM62 depends on the speed
grade of the SoC. However, this value is hardcoded in the DT for all
AM62 variants, potentially causing specifications to be exceeded. Moreover,
setting a common lower frequency for all variants increases boot time.
To prevent these issues, modify the DT at runtime from the R5 core to
adjust the A53 CPU frequency based on its speed grade.
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
AM62 SoC has multiple speed grades. Add function to return max A53 CPU
frequency based on grade. Fastest grade's max frequency also depends on
PMIC voltage, to simplify implementation use the smaller value.
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Simon Glass <sjg@chromium.org> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
Allow these functions to be compiled in when CONFIG_BOOTM is enabled,
even if CONFIG_CMD_BOOTM is not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZhaRdgAKCRDKSWXLKUoM
IS6LAKCdXJaEtlNLSC5IxeRJGmSTN4xPsACfdVL3mMzOZ1gw2+17uW1kHzzOgM4=
=vDHW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.07-rc1
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
The implementation of map_range() creates the requested mapping by
walking the page tables, iterating over multiple PTEs and/or descending
into existing table mappings as needed. When doing so, it assumes any
pre-existing valid PTE to be a table mapping. This assumption is wrong
if the platform code attempts to successively map two overlapping ranges
where the latter intersects a block mapping created for the former.
As a result, map_range() treats the existing block mapping as a table
mapping and descends into it i.e. starts interpreting the
previously-mapped range as an array of PTEs, writing to them and
potentially even descending further (extra fun with MMIO ranges!).
Instead, pass any valid non-table mapping to split_block(), which
ensures that it actually was a block mapping (calls panic() otherwise)
before splitting it.
Fixes: 41e2787f5ec4 ("arm64: Reduce add_map() complexity")
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Verdin AM62
Reviewed-by: Marc Zyngier <maz@kernel.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20228
- Convert imx8mp-beacon and verdin-imx8mm/verdin-imx8mp to OF_UPSTREAM.
- Enable PCIe NVMe support on imx8mp_beacon.
- Fix Ethernet and board detection on mx6cuboxi.
- Fix signature_block_hdr struct fields.
- Fix imx9_probe_mu prototype and make it to get called in
EVT_DM_POST_INIT_R.
- Test whether ethernet node is enabled before reading MAC EEPROM on
DHSOM SoMs.
- Ethernet, i2c, and USB support are now enabled by default
- The clock driver gets some bug fixes and cleanup
- Invalid FDTs are now properly detected in board_fdt_blob_setup().
- The pinctrl driver gains preparatory support for per-pin function
muxes.
- Support is added for two generations of Qualcomm HighSpeed USB PHY
- A power domain driver is added for the Globall Distributed Switch
Controllers on the GCC hardware block.
- SDM845 gains USB host mode support.
- OF_LIVE is enabled by default for Qualcomm platforms
- Some U-Boot devicetree compatibility fixups are added during init to
improve compatbility with upstream DT.
Move verdin-imx8mm and verdin-imx8mp to OF_UPSTREAM:
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This event callback imx9_probe_mu needs to be called in board_r
as well, because many ELE APIs depending on this MU probed
Signed-off-by: Ye Li <ye.li@nxp.com>
The i.MX6 Cubox-i and HummingBoards can have different PHYs at varying
addresses. U-Boot needs to auto-detect which phy is actually present,
and at which address it is responding.
Auto-detection from multiple phy nodes specified in device-tree does not
currently work correct. As a work-around merge all three possible phys
into one node with the special address 0xffffffff which indicates to the
generic phy driver to probe all addresses.
Signed-off-by: Josua Mayer <josua@solid-run.com>
[fabio: Added the changes to imx6qdl-sr-som-u-boot.dtsi.]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
The imx8mn-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mm-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mp-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Since meson G12A, G12B & SM1 based boards switched to using upstream DT,
so drop redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files
kept in arch/arm/dts directory for these boards.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-5-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable OF_UPSTREAM to use upstream DT and add amlogic/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-4-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Since meson GXL, GXM & AXG based boards switched to using upstream DT,
so drop redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files
kept in arch/arm/dts directory for these boards.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-3-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable OF_UPSTREAM to use upstream DT and add amlogic/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # khadas-vim3_android
Link: https://lore.kernel.org/r/20240329-u-boot-of-upstream-v2-2-2512ad3eb63d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The USB VBUS supply for the type-A port is enabled via a GPIO regulator.
This is incorrectly modelled in Linux where only the PCIe dependency is
expressed. The correct way to handle this will be through a
usb-connector node, but for now we'll just mark the regulator as
always-on so that it will be enabled automatically during boot.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Make sure we power on any boot-on or always-on regulators. These are
used for peripherals like USB on some platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We don't support the RPM(h)PD power domains in U-Boot, and we don't need
to - the necessary resources are on, and we aren't going to enter any
low power modes.
We could try using a no-op device, but this requires adding a compatible
for every platform, and just pollutes the driver model. So instead let's
just remove every "power-domains" property that references the RPM(h)pd
power controller. This takes <1ms as we're using OF_LIVE.
Of note, this only applies to drivers which are loading post-relocation.
Drivers loaded pre-reloc that reference the rpm(h)pd still need
DM_FLAG_DEFAULT_PD_CTRL_OFF in their flags.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We don't support USB super-speed in U-Boot yet, we lack the SS PHY
drivers, however from my testing even with a PHY driver there seem to be
other issues when talking to super-speed peripherals.
In pursuit of maintaining upstream DT compatibility, and simplifying
porting for new devices, let's implement the DT fixups necessary to
configure USB in high-speed only mode at runtime. The pattern is
identical for all Qualcomm boards that use the Synaptics DWC3
controller:
* Add an additional property on the Qualcomm wrapper node
* Remove the super-speed phy phandle and phy-name entries.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
There are cases when previous bootloader stage leaves some seemingly
valid value in r0, which in fact does not point to valid FDT
blob. This behavior was encountered when trying to boot U-Boot as
"hyp" loader on SA8155P-ADP.
To be sure that we really got the pointer to a device tree we need to
validate it with fdt_check_header() function.
Note: This approach is not 100% fool-proof, as get_prev_bl_fdt_addr()
theoretically can return a pointer to a region that is not physically
mapped and we will get data abort exception when fdt_check_header()
will try to access it. But at this early boot stage we don't know
where RAM is anyways so there is little we can do.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now sub-drivers for particular SoCs can register them as power domain
drivers. This is needed for upcoming SM8150 support, because it needs
to power up the Ethernet module.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: make ARCH_SNAPDRAGON select POWER_DOMAIN]
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add driver model support for sysreset via mvebu system controller. This is
currently only available for U-Boot proper.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The mvebu-reset driver is only needed by the mvebu PCIe driver, but
currently it is automatically selected if DM_RESET is enabled. Add the
condition of PCI_MVEBU also being enabled for mvebu-reset to be
selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The system-controller driver for 32-bit Armada is currently registered
as UCLASS_RESET, since it only provides enabling/disabling PCIe ports.
Rework it as UCLASS_SYSCON and bind mvebu-reset as a child device.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 35e29e89a386 ("arm: mvebu: Implement simple mvebu-reset driver
for enabling/disabling PCIe ports") made it so that the mvebu reset
driver for enabling/disabling PCIe ports is build if CONFIG_DM_RESET is
enabled. This is because PCI_MVEBU depends on DM_RESET.
But the driver should not be built for SPL. Indeed the PCI_MVEBU driver
is not supported in SPL now, and so the mvebu-reset driver is not needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE for Kirkwood boards. And so we can directly build
DTBs from dts/upstream/src/arm/marvell, and including *-u-boot.dtsi
files from arch/arm/dts/ directory.
Background:
The following 2 commands and filters were used in the analysis to determine
which upstream DTS and DTSI files can be used as they are, or need to have
modified/created *-u-boot.dtsi for u-boot specific implementation, and
which board should be opt-out from OF_UPSTREAM.
"git grep -li arch_kirkwood configs | xargs grep DEVICE_TREE | cut -d '"' -f2 | xargs -n1 sh -c 'diff -qs arch/arm/dts/$1.dts dts/upstream/src/arm/marvell/$1.dts' sh | grep differ"
"diff -qrbu arch/arm/dts/ dts/upstream/src/arm/marvell/ | grep kirkwood | grep ".dtsi ""
More detailed information can be found at:
https://lore.kernel.org/u-boot/20240328021825.17935-1-mibodhi@gmail.com/T/#u
I've regression tested this patch with the Zyxel NSA325 (Kirkwood 88F6282)
and Zyxel NSA310S (Kirkwood 88F6281). The Zyxel NSA325 board has a
USB 3.0 controller attached to the PCIe bus. And the Zyxel NSA310S
has an extensive overhaul in bindings and styles in upstream DTS version.
Tested-by: Michael Walle <michael@walle.cc> # on lschv2
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Except for Linux no other component (i.e., u-boot, fsbl
or BootRom) of the software stack supports software ecc
engine. So, make hw-ecc as the default ecc mode.
Update the same for mini u-boot nand configuration as well.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240325095013.29497-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
