Add support for PCIe clocks required to enable PCIe support on
iMX8MP SoC.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice*
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since commit cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
the apalis-imx8qm board no longer boots.
The reason is that the imx8qm clock driver does not handle the
LPUART IPG clocks inside get_rate(), set_rate() and enable() functions.
Fix the boot regression by adding the LPUART IPG entries.
Fixes: cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
the colibri-imx8qxp board no longer boots.
The reason is that the imx8qxp clock driver does not handle the
LPUART IPG clocks inside get_rate(), set_rate() and enable() functions.
Fix the boot regression by adding the LPUART IPG entries.
Fixes: cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
Acked-by: Sean Anderson <seanga2@gmail.com>
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
This patch is to enable Agilex5 platform for Intel
product. Changes, modification and new files are
created for board, dts, configs and makefile to
create the base for Agilex5.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
Include the clock and lpsc tree files needed for the wkup spl to
initialize the proper PLLs and power domains to boot the SoC.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Add clk and device data which can be used by respective drivers
to configure clocks and PSC.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
When U-Boot as running as the first stage bootloader on MSM8916 devices,
early debug UART requires turning on the clocks (for some reason the
pre-loader turns them off?!).
To simplify developing for this platform, allow the
apq8016_clk_init_uart() function to be called externally. Developers can
call this from the serial_msm debug uart driver to configure the clocks
before the driver model is available.
As it is only possible to enable early debug UART in custom builds of
U-Boot, this solution at least gives developers the option.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Don't use hardcoded clock IDs, use the IDs from the dt-bindings to be
compatible with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We should be returning the rate that we set the clock to, drivers like
MMC rely on this. So fix it.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust the apq8016 and apq8096 drivers to use the upstream compatible
properties, and adjust the associated dts files in U-Boot.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
When enabling/disabling a clock or reset signal, confirm that the change
has completed before returning from the function. A somewhat arbitrary
100ms timeout is defined to ensure that the system doesn't lock up in
the case of an error.
Since we need to dynamically determine if we're waiting for a 0 bit or a
1 bit, it's easier to use wait_for_bit_32() than readl_poll_timeout().
This change is needed for reliable initialization of the I2C driver
which is added in a following patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To prepare support for multiple register layouts pointers to register
tables where added to struct cpg_mssr_info. These pointers are suppose
to be filled in at probe time and no intended change in behavior was
intended.
However the new pointers where only filled in by some paths of the
driver implemented in clk-rcar-gen3.c. The path implemented in
clk-rcar-gen2.c was not updated leaving the pointers uninitialized
leading to a crash when trying to probe the clocks.
Fix this by filling in the pointers in the Gen2 code path with the
values used before they where moved to struct cpg_mssr_info.
Fixes: d413214fb748 ("clk: renesas: Add register pointers into struct cpg_mssr_info")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R8A7791 Porter
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Existing gpio-gate-clock driver acts like a simple GPIO switch without any
effect on gated clock. Add actual clock actions into enable/disable ops and
implement get_rate op by passing gated clock if it is enabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20240110160956.4476-2-clamor95@gmail.com
[ sorted includes ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When we call clk_get_rate(), we expect to get clock rate value as
ulong.
In that case we should not use log_ret() macro since it use internally
an int.
Otherwise we may return an invalid/truncated clock rate value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Fixes: 5c5992cb90c ("clk: Add debugging for return values")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/87o7erv9p4.fsf@baylibre.com
Amlogic SoCs embeds an hardware clock measure block, port it
from Linux and implement it as a UCLK_CLK with only the dump
op and fail-only xlate.
Based on the Linux driver introduced in [1].
[1] commit 2b45ebef39a2 ("soc: amlogic: Add Meson Clock Measure driver").
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231218-uboot-meson-clk-msr-v3-1-acf4d90ccfee@linaro.org
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Heavily influenced by its Linux kernel counterpart. It's implemented on
top of recently added Samsung CCF clock framework API. For now only UART
leaf clocks are implemented, along with all preceding clocks in CMU_TOP
and CMU_PERI. The UART baud clock is required in the serial driver, to
get its rate for the consequent baud rate calculation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heavily based on Linux kernel Samsung clock framework, with some changes
to accommodate the differences in U-Boot CCF implementation. It's also
quite minimal as compared to the Linux version.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PLL utilities code is only used by clk-exynos7420 driver at the moment.
Move it into clk-exynos7420 to make clk-pll.c file available for CCF PLL
clocks implementation, which is coming in the next patches.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
MEMCLKMGR_EXTCNTRST_C0CNTRST register defined as BIT[0] in documentation
but it is wrongly defined as BIT[7] in u-boot code. This register is used
to hold associated pingpong counter in reset
while PLL and 5:1 mux configuration is changed.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Many gate clocks can be enabled with a single register write, add support
for defining these simple gate clocks and add the ones found on SDM845.
While we're here, inline clk_init_uart() into msm_set_rate().
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Add ZG clock macro into rcar-gen3-cpg.h to cover the new clock type .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
