This excludes options that are inherently ARM-specific or are specific
to legacy non-DM drivers.
Some help text is cleaned up along the way.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This keeps all of the defaults for sunxi platforms in one place. Most of
these only depend on architecture-independent features of the SoC (clock
tree or SRAM layout) anyway.
No functional change; just some minor help text cleanup.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This was already supported by every machine type. It is unlikely that
any new SoC support will be added without SPL support.
Signed-off-by: Samuel Holland <samuel@sholland.org>
To maintain consistent behavior across architectures, most of the
options selected by ARCH_SUNXI should be selected for the D1 SoC as
well. To accomplish this, select them from BOARD_SUNXI instead.
No functional change here. Lines are only moved and alphabetized.
Signed-off-by: Samuel Holland <samuel@sholland.org>
With the introduction of the Allwinner D1, the sunxi board family now
spans multiple architectures (ARM and RISC-V). Since ARCH_SUNXI depends
on ARM, it cannot be used to gate architecture-independent options.
Specifically, this means the board Kconfig file cannot be sourced from
inside the "if ARCH_SUNXI" block.
Introduce a new BOARD_SUNXI symbol that can be selected by both
ARCH_SUNXI now and the new RISC-V SoC symbols when they are added, and
use it to gate the architecture-independent board options.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Some of the selected symbols have a user-visible dependency. Make the
selections conditional on that dependency to avoid creating invalid
configurations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Two of these selections are redundant and have no effect:
- DM_KEYBOARD is selected by USB_KEYBOARD
- DM_MMC is selected by MMC
This selection has no effect by default and is unnecessarily strong:
- USB_STORAGE is implied by DISTRO_DEFAULTS
Signed-off-by: Samuel Holland <samuel@sholland.org>
We tried to enable USB_EHCI_GENERIC and USB_OHCI_GENERIC by default.
This did not work because those symbols depend on USB_EHCI_HCD and
USB_OHCI_HCD, which were not enabled. Fix this by implying all four.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC has a DM driver and binds device tree subnodes, the
GPIO device can be bound that way, instead of from inside board code.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it does not differentiate among
the supported compatibles.
Signed-off-by: Samuel Holland <samuel@sholland.org>
These PMICs each have two GPIO pins, and are supported by the axp_gpio
driver. In order to convert the axp_gpio driver to probe using the
device tree, the corresponding device tree nodes must be present. Add
them, following the same binding as the AXP209 and AXP813.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, we can switch to DM_GPIO for these pins with no loss in
functionality. Since the driver now gets its pin configuration from
the device tree, we can remove the Kconfig symbols.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This adds a new PSCI implementation which communicates with SCP firmware
running on the AR100 using the SCPI protocol. This allows it to support
the full set of PSCI v1.1 features, including CPU idle states, system
suspend, and multiple reset methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Add the new option, function IDs, and prototypes for PSCI v1.1
implementations. In the process, fix some issues with the existing
definitions:
- Fix the incorrectly-named ARM_PSCI_0_2_FN64_SYSTEM_RESET2.
- Replace the deprecated "affinity_level" naming with "power_level".
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that issues with the BROM have been sorted out, we can implement
PSCI system suspend on H3 by delegating to SCP firmware. Let's start by
including the firmware in the FIT image and starting the coprocessor if
valid firmware is loaded.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Due to a bug in the H3 SoC, where the CPU 0 hotplug flag cannot be
written, resuming CPU 0 requires using the "Super Standby" code path in
the BROM instead of the hotplug path. This path requires jumping to an
eGON image in SRAM.
Add support to the build system to generate this eGON image and include
it in the FIT, and add code to direct the BROM to its location in SRAM.
Since the Super Standby code path in the BROM initializes the CPU and
AHB1 clocks to 24 MHz, those registers need to be restored after control
passes back to U-Boot. Furthermore, because the BROM lowers the AHB1
clock divider to /1 before switching to the lower-frequency parent,
PLL_PERIPH0 must be bypassed to prevent AHB1 from temporarily running at
600 MHz. Otherwise, this locks up the SoC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
With one exception (sun9i), all sunxi SoCs released to date use variants
of the same USB PHY. Instead of requiring each new SoC to duplicate the
PHY driver selection, enable it by default.
Series-to: Andre Przywara <andre.przywara@arm.com>
Series-to: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Do not try to send an SGI from CPU 0 to itself. Since FIQs are masked
when entering monitor mode, this will hang. Plus, CPU 0 cannot fully
power itself off anyway. Instead, have it turn FIQs back on and continue
servicing SGIs from other cores.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that Crust (SCP firmware) has support for H3, we need a FIT image to
load it. H3 also needs to load a SoC-specific eGon blob to support CPU 0
hotplug. Let's first enable FIT support before adding extra firmware.
Update the binman description to work on either 32-bit or 64-bit SoCs:
- Make BL31 optional, since it is not used on 32-bit SoCs (though BL32
may be used in the future).
- Explicitly set the minimum offset of the FIT to 32 KiB, since SPL on
some boards is still only 24 KiB large even with FIT support enabled.
CONFIG_SPL_PAD_TO cannot be used because it is not defined for H616.
FIT unlocks more features (signatures, multiple DTBs, etc.), so enable
it by default. A10 (sun4i) only has 24 KiB of SRAM A1, so it needs
SPL_FIT_IMAGE_TINY. For simplicity, enable that option everywhere.
Cover-letter:
sunxi: SPL FIT support for 32-bit sunxi SoCs
This series makes the necessary changes so 32-bit sunxi SoCs can load
additional device trees or firmware from SPL along with U-Boot proper.
There was no existing binman entry property that put the FIT at the
right offset. The minimum offset is 32k, but this matches neither the
SPL size (which is no more than 24k on some SoCs) nor the FIT alignment
(which is 512 bytes in practice due to SPL size constraints). So instead
of adding a new property, I fixed what is arguably a bug in the offset
property -- though this strategy will not work if someone is
intentionally creating overlapping entries.
END
Series-to: sunxi
Series-to: sjg
Signed-off-by: Samuel Holland <samuel@sholland.org>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
For legacy reasons we were defining the card detect GPIO for all sunxi
boards in each board's defconfig.
There is actually no need for a card-detect check in the SPL code (which
consequently has been removed already), and also in U-Boot proper we
have DM code to query the CD GPIO name from the device tree.
That means we don't have any user of that information left, so can
remove the definitions from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove
it, along with the rest of the support for AXP virtual GPIOs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the USB PHY driver uses the device tree to get VBUS supply
regulators, these Kconfig symbols are unused. Remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
