Now that the USB PHY driver uses the device tree to get VBUS supply
regulators, these Kconfig symbols are unused. Remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <samuel@sholland.org>
On many boards, the USB ports are powered by a GPIO-controlled fixed
regulator. In preparation for switching the USB PHY driver to use the
regulator uclass instead of driving the GPIO directly, ensure these
boards have fixed regulator support enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
On many boards, the USB ports are powered by the PMIC's "drivevbus"
regulator. In preparation for switching the USB PHY driver to use the
regulator uclass instead of a virtual GPIO pin, ensure these boards
have AXP PMIC regulator support enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that some regulator driver exists for this PMIC, add support for
probing regulator drivers from the device tree subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The first AXP regulator converted to use the regulator uclass is the
drivevbus switch, since it is used by the USB PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.
The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.
Additionally, the following board intentionally omits the property
because VBUS is always enabled:
- Nintendo_NES_Classic_Edition_defconfig /
sun8i-r16-nintendo-nes-classic
The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
To quote Simon:
This series provides an implementation of VBE from TPL through to U-Boot
proper, using VBE to load the relevant firmware stages. It buils a single
image.bin file containing all the phases:
TPL - initial phase, loads VPL using binman symbols
VPL - main firmware phase, loads SPL using VBE parameters
SPL - loads U-Boot proper using VBE parameters
U-Boot - final firmware phase, where OS booting is processed
This series does not include the OS-booting phase. That will be the
subject of a future series.
The implementation is entirely handled by sandbox. It should be possible
to enable this on a real board without much effort, but that is also the
subject of a future series.
Use a manual test for the VBE test, so we can make the pytest and the
C unit test work together properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the various features needed in VPL, by adding Kconfig options.
Update the defconfig for sandbox_vpl so that the build for each phase
includes what is needed. Drop LZMA for now and make sure partition support
is omitted in SPL, since it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need the U-Boot prefix on the version and in fact it is harmful
since pytest gets confused seeing the U-Boot banner bring displayed when
the version is printed.
Drop the prefix from the string.
We could produce an entirely new string from the component parts, but this
adds to the rodata size and would break the use of version_string as the
only thing which holds this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
VBE supports booting firmware during the SPL phases, i.e. so that VPL can
start SPL and SPL can start U-Boot.
It also supports booting an OS, when in U-Boot.
As a first step towards these features, add functions to indicate the
current VBE phase. The firmware selection is done in VPL and the OS
selection is done in U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we only support a single loader of each time. Extra ones are
ignored. This means that only one BOOT_DEVICE_BOARD can be used in the SPL
image.
This is inconvenient since we sometimes want to provide several
board-specific drivers, albeit at different priorties. Add support for
this.
This should have no functional change for existing boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
The vbe_fixup file handles device tree fixups, but these are called OS
requests in VBE. Rename the file to reflect its wider purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for filtering out FIT images by phase. Rather than adding yet
another argument to this already overloaded function, use a composite
value, where the phase is only added in if needed.
The FIT config is still selected (and verified) as normal, but the images
are selected based on the phase.
Tests for this come in a little later, as part of the updated VPL test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to mark an image as related to a phase, so we can
easily load all the images for SPL or for U-Boot proper.
Add this to the FIT specification, along with some access functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This happens every time sandbox moves to the next phase so is not very
interesting. Display the message only when debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When MMC_WRITE is disabled this driver produced a build error. Fix this.
Also update a comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the correct SPL_TPL_ variable so that these features can be enabled in
TPL and VPL as needed.
Disable it by default in TPL to avoid any code-size increase. No boards
are actually using it since the Makefile rules don't allow including
drivers/block/ with TPL_DM enabled. It can be manually enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add test coverage for blk_write() as well.
The blk_erase() is not tested for now as the USB stor interface does not
support erase.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have functions called blk_dread(), etc., which take a
struct blk_desc * to refer to the block device. Add some functions which
use udevice instead, since this is more in keeping with how driver model
is supposed to work.
Update one of the tests to use this.
Note that it would be nice to update the functions in disk-uclass.c to use
these new functions. However they are not quite the same. For example,
disk_blk_read() adds the partition offset to 'start' when calling the
cache read/fill functions, but does not with part_blk_read(), which does
the addition itself. So as designed the code is duplicated.
Signed-off-by: Simon Glass <sjg@chromium.org>
The use of 'block_dev' in this context is confusing, since it is not a
pointer to a device, just to some information about it. Rename this to
'desc', as is more commonly used, since it is a block descriptor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glplk@gmx.de>
Use the uclass type as the first part of the function name, to be
consistent with the methods in other block drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests currently return 0 when they want to be skipped. Update them to
return -EAGAIN instead, so they are counted as skipped.
A few tests are in two parts, with the latter part being skipped in
certain situations. Split these into two and use the correct condition for
the second part.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is possible for a test to skip itself by returning -EAGAIN
but this is not recorded. An existing example is in test_pre_run() with
the "Console recording disabled" check.
Keep a track of skipped tests and report the total at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In some cases the ELF version of SPL builds may be packaged, rather
than a binary .bin file. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is used by several etypes and we plan to add more that use
it. Make symbol writing a feature of the base class to reduce the code
duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
