config BOARD_SUNXI bool select BINMAN select CLK select CMD_GPIO if GPIO select CMD_MMC if MMC select CMD_USB if DISTRO_DEFAULTS && USB_HOST select DM select DM_ETH if NET select DM_GPIO if GPIO select DM_I2C if I2C select DM_SCSI if BLK && SCSI select DM_SERIAL if SERIAL select DM_SPI if SPI select DM_SPI_FLASH if SPI select OF_BOARD_SETUP select PINCTRL select SPL_SEPARATE_BSS if SPL select SUPPORT_SPL select SYS_RELOC_GD_ENV_ADDR select USB if DISTRO_DEFAULTS select USB_KEYBOARD if DISTRO_DEFAULTS && USB_HOST select USE_PREBOOT imply BOARD_LATE_INIT imply CMD_DM imply CMD_GPT imply CMD_UBI if MTD_RAW_NAND imply DISTRO_DEFAULTS imply FAT_WRITE imply FIT imply OF_LIBFDT_OVERLAY imply PRE_CONSOLE_BUFFER imply SPL imply SPL_GPIO imply SPL_LIBCOMMON_SUPPORT imply SPL_LIBGENERIC_SUPPORT imply SPL_MMC if MMC imply SPL_POWER imply SPL_SERIAL imply SUNXI_GPIO imply SYS_I2C_MVTWSI imply SYS_NS16550 imply SYSRESET imply SYSRESET_WATCHDOG imply SYSRESET_WATCHDOG_AUTO imply USB_EHCI_GENERIC imply USB_EHCI_HCD imply USB_GADGET imply USB_OHCI_GENERIC imply USB_OHCI_HCD imply WDT if BOARD_SUNXI config IDENT_STRING default " Allwinner Technology" config SPL_STACK_R_ADDR default 0x81e00000 if MACH_SUNIV default 0x4fe00000 if MACH_SUN4I default 0x4fe00000 if MACH_SUN5I default 0x4fe00000 if MACH_SUN6I default 0x4fe00000 if MACH_SUN7I default 0x4fe00000 if MACH_SUN8I default 0x2fe00000 if MACH_SUN9I default 0x4fe00000 if MACH_SUN50I default 0x4fe00000 if SUN50I_GEN_H6 config SUNXI_MINIMUM_DRAM_MB int default 32 if MACH_SUNIV default 64 if MACH_SUN8I_V3S default 256 help Minimum DRAM size expected on the board. Traditionally we assumed 256 MB, so that U-Boot would load at 160MB. With co-packaged DRAM we have smaller sizes, though, so U-Boot's own load address and the default payload addresses must be shifted down. This is expected to be fixed by the SoC selection. config SUNXI_SRAM_ADDRESS hex default 0x10000 if MACH_SUN9I || MACH_SUN50I || MACH_SUN50I_H5 default 0x20000 if SUN50I_GEN_H6 default 0x0 help Older Allwinner SoCs have their boot mask ROM mapped just below 4GB, with the first SRAM region located at address 0. Newer SoCs map the boot ROM at address 0 instead and move the SRAM to a different address. config SYS_BOARD default "sunxi" config SYS_CLK_FREQ default 408000000 if MACH_SUNIV default 1008000000 if MACH_SUN4I default 1008000000 if MACH_SUN5I default 1008000000 if MACH_SUN6I default 912000000 if MACH_SUN7I default 1008000000 if MACH_SUN8I default 1008000000 if MACH_SUN9I default 816000000 if MACH_SUN50I || MACH_SUN50I_H5 default 888000000 if MACH_SUN50I_H6 default 1008000000 if MACH_SUN50I_H616 config SYS_CONFIG_NAME default "suniv" if MACH_SUNIV default "sun4i" if MACH_SUN4I default "sun5i" if MACH_SUN5I default "sun6i" if MACH_SUN6I default "sun7i" if MACH_SUN7I default "sun8i" if MACH_SUN8I default "sun9i" if MACH_SUN9I default "sun50i" if MACH_SUN50I default "sun50i" if MACH_SUN50I_H6 default "sun50i" if MACH_SUN50I_H616 config SYS_SOC default "sunxi" menu "sunxi board options" choice prompt "SPL Image Type" depends on SPL default SPL_IMAGE_TYPE_SUNXI_EGON config SPL_IMAGE_TYPE_SUNXI_EGON bool "eGON (normal)" help Select this option to embed the SPL binary in an eGON.BT0 image, which is compatible with the normal boot ROM (NBROM). This is usually the correct option to choose. config SPL_IMAGE_TYPE_SUNXI_TOC0 bool "TOC0 (secure)" help Select this option to embed the SPL binary in a TOC0 image, which is compatible with the secure boot ROM (SBROM). endchoice config SPL_IMAGE_TYPE string default "sunxi_egon" if SPL_IMAGE_TYPE_SUNXI_EGON default "sunxi_toc0" if SPL_IMAGE_TYPE_SUNXI_TOC0 endmenu endif