mirror of
https://github.com/smaeul/u-boot.git
synced 2025-10-31 12:08:19 +00:00
079a136c35
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h used to be included but CONFIG_BOOTP_MASK was not defined. Remove lingering references to CFG_CMD_* symbols. Signed-off-by: Jon Loeliger <jdl@freescale.com>
241 lines
7.3 KiB
C
241 lines
7.3 KiB
C
/*
|
|
* U-boot - Configuration file for BF533 EZKIT board
|
|
*/
|
|
|
|
#ifndef __CONFIG_EZKIT533_H__
|
|
#define __CONFIG_EZKIT533_H__
|
|
|
|
#define CONFIG_BAUDRATE 57600
|
|
#define CONFIG_STAMP 1
|
|
|
|
#define CONFIG_BOOTDELAY 5
|
|
#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
|
|
|
|
#define CFG_LONGHELP 1
|
|
#define CONFIG_CMDLINE_EDITING 1
|
|
#define CONFIG_LOADADDR 0x01000000 /* default load address */
|
|
#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
|
|
/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
|
|
|
|
#define CONFIG_DRIVER_SMC91111 1
|
|
#define CONFIG_SMC91111_BASE 0x20310300
|
|
|
|
#if 0
|
|
#define CONFIG_MII
|
|
#define CFG_DISCOVER_PHY
|
|
#endif
|
|
|
|
#define CONFIG_RTC_BFIN 1
|
|
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
|
|
|
|
/*
|
|
* Boot Mode Set
|
|
* Blackfin can support several boot modes
|
|
*/
|
|
#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
|
|
#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
|
|
#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
|
|
/* Define the boot mode */
|
|
#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
|
|
/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
|
|
|
|
#define CONFIG_PANIC_HANG 1
|
|
|
|
#define ADSP_BF531 0x31
|
|
#define ADSP_BF532 0x32
|
|
#define ADSP_BF533 0x33
|
|
#define BFIN_CPU ADSP_BF533
|
|
|
|
/* This sets the default state of the cache on U-Boot's boot */
|
|
#define CONFIG_ICACHE_ON
|
|
#define CONFIG_DCACHE_ON
|
|
|
|
/* Define where the uboot will be loaded by on-chip boot rom */
|
|
#define APP_ENTRY 0x00001000
|
|
|
|
/* CONFIG_CLKIN_HZ is any value in Hz */
|
|
#define CONFIG_CLKIN_HZ 27000000
|
|
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
|
|
/* 1=CLKIN/2 */
|
|
#define CONFIG_CLKIN_HALF 0
|
|
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
|
|
/* 1=bypass PLL */
|
|
#define CONFIG_PLL_BYPASS 0
|
|
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
|
|
/* Values can range from 1-64 */
|
|
#define CONFIG_VCO_MULT 22
|
|
/* CONFIG_CCLK_DIV controls what the core clock divider is */
|
|
/* Values can be 1, 2, 4, or 8 ONLY */
|
|
#define CONFIG_CCLK_DIV 1
|
|
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
|
|
/* Values can range from 1-15 */
|
|
#define CONFIG_SCLK_DIV 5
|
|
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
|
|
/* Values can range from 2-65535 */
|
|
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
|
|
#define CONFIG_SPI_BAUD 2
|
|
#define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
|
|
#if ( CONFIG_CLKIN_HALF == 0 )
|
|
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
|
|
#else
|
|
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
|
|
#endif
|
|
|
|
#if (CONFIG_PLL_BYPASS == 0)
|
|
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
|
|
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
|
|
#else
|
|
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
|
|
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
|
|
#endif
|
|
|
|
#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
|
|
#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
|
|
#define CONFIG_MEM_MT48LC16M16A2TG_75 1
|
|
|
|
#define CONFIG_LOADS_ECHO 1
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_CMD_DATE
|
|
|
|
|
|
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
|
|
|
|
#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
|
|
#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
|
|
#define CFG_LOAD_ADDR 0x01000000 /* default load address */
|
|
#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
|
|
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
#define CFG_SDRAM_BASE 0x00000000
|
|
#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
|
|
#define CFG_FLASH_BASE 0x20000000
|
|
|
|
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
|
|
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
|
|
#define CFG_GBL_DATA_SIZE 0x4000
|
|
#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
|
|
#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
|
|
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
#define CFG_FLASH0_BASE 0x20000000
|
|
#define CFG_FLASH1_BASE 0x20200000
|
|
#define CFG_FLASH2_BASE 0x20280000
|
|
#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
|
|
#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
|
|
|
|
#define CFG_ENV_IS_IN_FLASH 1
|
|
#define CFG_ENV_ADDR 0x20020000
|
|
#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
|
|
|
|
/* JFFS Partition offset set */
|
|
#define CFG_JFFS2_FIRST_BANK 0
|
|
#define CFG_JFFS2_NUM_BANKS 1
|
|
/* 512k reserved for u-boot */
|
|
#define CFG_JFFS2_FIRST_SECTOR 11
|
|
|
|
|
|
/*
|
|
* Stack sizes
|
|
*/
|
|
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
|
|
|
|
#define POLL_MODE 1
|
|
#define FLASH_TOT_SECT 40
|
|
#define FLASH_SIZE 0x220000
|
|
#define CFG_FLASH_SIZE 0x220000
|
|
|
|
/*
|
|
* Initialize PSD4256 registers for using I2C
|
|
*/
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* I2C settings
|
|
* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
|
|
*/
|
|
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
|
|
/*
|
|
* Software (bit-bang) I2C driver configuration
|
|
*/
|
|
#define PF_SCL PF0
|
|
#define PF_SDA PF1
|
|
|
|
#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
|
|
#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
|
|
#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
|
|
#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
|
|
#define I2C_SDA(bit) if(bit) { \
|
|
*pFIO_FLAG_S = PF_SDA; \
|
|
asm("ssync;"); \
|
|
} \
|
|
else { \
|
|
*pFIO_FLAG_C = PF_SDA; \
|
|
asm("ssync;"); \
|
|
}
|
|
#define I2C_SCL(bit) if(bit) { \
|
|
*pFIO_FLAG_S = PF_SCL; \
|
|
asm("ssync;"); \
|
|
} \
|
|
else { \
|
|
*pFIO_FLAG_C = PF_SCL; \
|
|
asm("ssync;"); \
|
|
}
|
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
|
|
#define CFG_I2C_SPEED 50000
|
|
#define CFG_I2C_SLAVE 0xFE
|
|
|
|
#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
|
|
|
|
/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
|
|
/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
|
|
#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
|
|
~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
|
|
#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
|
|
B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
|
|
*/
|
|
#define AMGCTLVAL 0xFF
|
|
#define AMBCTL0VAL 0x7BB07BB0
|
|
#define AMBCTL1VAL 0xFFC27BB0
|
|
|
|
#define CONFIG_VDSP 1
|
|
|
|
#ifdef CONFIG_VDSP
|
|
#define ET_EXEC_VDSP 0x8
|
|
#define SHT_STRTAB_VDSP 0x1
|
|
#define ELFSHDRSIZE_VDSP 0x2C
|
|
#define VDSP_ENTRY_ADDR 0xFFA00000
|
|
#endif
|
|
|
|
#endif
|