mirror of
https://github.com/smaeul/u-boot.git
synced 2025-11-03 21:48:15 +00:00
983e37007d
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
105 lines
2.5 KiB
C
105 lines
2.5 KiB
C
/*
|
|
* clk-synthesizer.c
|
|
*
|
|
* Clock synthesizer apis
|
|
*
|
|
* Copyright (C) 2016, Texas Instruments, Incorporated - http://www.ti.com/
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/clk_synthesizer.h>
|
|
#include <i2c.h>
|
|
|
|
/**
|
|
* clk_synthesizer_reg_read - Read register from synthesizer.
|
|
* @addr: addr within the i2c device
|
|
* buf: Buffer to which value is to be read.
|
|
*
|
|
* For reading the register from this clock synthesizer, a command needs to
|
|
* be send along with enabling byte read more, and then read can happen.
|
|
* Returns 0 on success
|
|
*/
|
|
static int clk_synthesizer_reg_read(int addr, uint8_t *buf)
|
|
{
|
|
int rc;
|
|
|
|
/* Enable Bye read */
|
|
addr = addr | CLK_SYNTHESIZER_BYTE_MODE;
|
|
|
|
/* Send the command byte */
|
|
rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
|
|
if (rc)
|
|
printf("Failed to send command to clock synthesizer\n");
|
|
|
|
/* Read the Data */
|
|
return i2c_read(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
|
|
}
|
|
|
|
/**
|
|
* clk_synthesizer_reg_write - Write a value to register in synthesizer.
|
|
* @addr: addr within the i2c device
|
|
* val: Value to be written in the addr.
|
|
*
|
|
* Enable the byte read mode in the address and start the i2c transfer.
|
|
* Returns 0 on success
|
|
*/
|
|
static int clk_synthesizer_reg_write(int addr, uint8_t val)
|
|
{
|
|
uint8_t cmd[2];
|
|
int rc = 0;
|
|
|
|
/* Enable byte write */
|
|
cmd[0] = addr | CLK_SYNTHESIZER_BYTE_MODE;
|
|
cmd[1] = val;
|
|
|
|
rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, cmd, 2);
|
|
if (rc)
|
|
printf("Clock synthesizer reg write failed at addr = 0x%x\n",
|
|
addr);
|
|
return rc;
|
|
}
|
|
|
|
/**
|
|
* setup_clock_syntherizer - Program the clock synthesizer to get the desired
|
|
* frequency.
|
|
* @data: Data containing the desired output
|
|
*
|
|
* This is a PLL-based high performance synthesizer which gives 3 outputs
|
|
* as per the PLL_DIV and load capacitor programmed.
|
|
*/
|
|
int setup_clock_synthesizer(struct clk_synth *data)
|
|
{
|
|
int rc;
|
|
uint8_t val;
|
|
|
|
rc = i2c_probe(CLK_SYNTHESIZER_I2C_ADDR);
|
|
if (rc) {
|
|
printf("i2c probe failed at address 0x%x\n",
|
|
CLK_SYNTHESIZER_I2C_ADDR);
|
|
return rc;
|
|
}
|
|
|
|
rc = clk_synthesizer_reg_read(CLK_SYNTHESIZER_ID_REG, &val);
|
|
if (val != data->id)
|
|
return rc;
|
|
|
|
/* Crystal Load capacitor selection */
|
|
rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_XCSEL, data->capacitor);
|
|
if (rc)
|
|
return rc;
|
|
rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_MUX_REG, data->mux);
|
|
if (rc)
|
|
return rc;
|
|
rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV2_REG, data->pdiv2);
|
|
if (rc)
|
|
return rc;
|
|
rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV3_REG, data->pdiv3);
|
|
if (rc)
|
|
return rc;
|
|
|
|
return 0;
|
|
}
|