smaeul-u-boot/arch/arm/mach-omap2/am33xx/chilisom.c

/*
 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
 * Copyright (C) 2017, Grinn - http://grinn-global.com/
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/clk_synthesizer.h>
#include <asm/arch/cpu.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/emif.h>
#include <asm/io.h>
#include <errno.h>
#include <i2c.h>
#include <power/tps65217.h>
#include <spl.h>

#ifndef CONFIG_SKIP_LOWLEVEL_INIT

static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;

static struct module_pin_mux i2c0_pin_mux[] = {
	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
			PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
			PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
	{-1},
};

static struct module_pin_mux nand_pin_mux[] = {
	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
	{-1},
};

static void enable_i2c0_pin_mux(void)
{
	configure_module_pin_mux(i2c0_pin_mux);
}

void chilisom_enable_pin_mux(void)
{
	/* chilisom pin mux */
	configure_module_pin_mux(nand_pin_mux);
}

static const struct ddr_data ddr3_chilisom_data = {
	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};

static const struct cmd_control ddr3_chilisom_cmd_ctrl_data = {
	.cmd0csratio = MT41K256M16HA125E_RATIO,
	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd1csratio = MT41K256M16HA125E_RATIO,
	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd2csratio = MT41K256M16HA125E_RATIO,
	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};

static struct emif_regs ddr3_chilisom_emif_reg_data = {
	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
	.ocp_config = 0x00141414,
	.zq_config = MT41K256M16HA125E_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
};

void chilisom_spl_board_init(void)
{
	int mpu_vdd;
	int usb_cur_lim;

	enable_i2c0_pin_mux();

	/* Get the frequency */
	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);


	if (i2c_probe(TPS65217_CHIP_PM))
		return;

	/*
	 * Increase USB current limit to 1300mA or 1800mA and set
	 * the MPU voltage controller as needed.
	 */
	if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
	} else {
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
	}

	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
			       TPS65217_POWER_PATH,
			       usb_cur_lim,
			       TPS65217_USB_INPUT_CUR_LIMIT_MASK))
		puts("tps65217_reg_write failure\n");

	/* Set DCDC3 (CORE) voltage to 1.125V */
	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
		puts("tps65217_voltage_update failure\n");
		return;
	}
	/* Set CORE Frequencies to OPP100 */
	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);

	/* Set DCDC2 (MPU) voltage */
	if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
		puts("tps65217_voltage_update failure\n");
		return;
	}

	/* Set LDO3 to 1.8V and LDO4 to 3.3V */
	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
			       TPS65217_DEFLS1,
			       TPS65217_LDO_VOLTAGE_OUT_1_8,
			       TPS65217_LDO_MASK))
		puts("tps65217_reg_write failure\n");

	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
			       TPS65217_DEFLS2,
			       TPS65217_LDO_VOLTAGE_OUT_3_3,
			       TPS65217_LDO_MASK))
		puts("tps65217_reg_write failure\n");

	/* Set MPU Frequency to what we detected now that voltages are set */
	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
}

#define OSC	(V_OSCK/1000000)
const struct dpll_params dpll_ddr_chilisom = {
		400, OSC-1, 1, -1, -1, -1, -1};

const struct dpll_params *get_dpll_ddr_params(void)
{
	return &dpll_ddr_chilisom;
}

const struct ctrl_ioregs ioregs_chilisom = {
	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
};

void sdram_init(void)
{
	config_ddr(400, &ioregs_chilisom,
		   &ddr3_chilisom_data,
		   &ddr3_chilisom_cmd_ctrl_data,
		   &ddr3_chilisom_emif_reg_data, 0);
}

#endif /* CONFIG_SKIP_LOWLEVEL_INIT */