mirror of
https://github.com/smaeul/u-boot.git
synced 2025-10-31 12:08:19 +00:00
d9252fcde1
Replace the board specific docs with a generic board.rst file which documents the build/boot process for the sdm845 and qcs404 boards now that the only differences are the DTB in use. At the same time, create a debugging page to document some useful snippets and tips for working with Qualcomm platforms. Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
62 lines
1.6 KiB
ReStructuredText
62 lines
1.6 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
.. sectionauthor:: Caleb Connolly <caleb.connolly@linaro.org>
|
|
|
|
Qualcomm debugging
|
|
==================
|
|
|
|
About this
|
|
----------
|
|
|
|
This page describes how to enable early UART and other debugging techniques
|
|
for Qualcomm boards.
|
|
|
|
Enable debug UART
|
|
-----------------
|
|
|
|
Newer boards (SDM845 and newer, those with GENI SE UART)
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Open ``configs/qcom_defconfig`` and add the following snippet to the bottom:
|
|
|
|
CONFIG_BAUDRATE=115200
|
|
|
|
# Uncomment to enable UART pre-relocation
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
# This is the address of the debug-uart peripheral
|
|
# The value here is for SDM845, other platforms will vary
|
|
CONFIG_DEBUG_UART_BASE=0xa84000
|
|
# Boards older than ~2018 pre-date the GENI driver and unfortunately
|
|
# aren't supported here
|
|
CONFIG_DEBUG_UART_MSM_GENI=y
|
|
# For sdm845 this is the UART clock rate
|
|
CONFIG_DEBUG_UART_CLOCK=7372800
|
|
# Most newer boards have an oversampling value of 16 instead
|
|
# of 32, they need the clock rate to be doubled
|
|
#CONFIG_DEBUG_UART_CLOCK=14745600
|
|
|
|
Then build as normal (don't forget to ``make qcom_defconfig``` again).
|
|
|
|
Older boards (db410c and db820c)
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Open ``configs/dragonboard<BOARD>_defconfig``
|
|
|
|
CONFIG_BAUDRATE=115200
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
# db410c - 0x78b0000
|
|
# db820c - 0x75b0000
|
|
CONFIG_DEBUG_UART_BASE=0x75b0000
|
|
CONFIG_DEBUG_UART_MSM=y
|
|
CONFIG_DEBUG_UART_CLOCK=7372800
|
|
#CONFIG_DEBUG_UART_SKIP_INIT=y
|
|
|
|
CONFIG_LOG=y
|
|
CONFIG_HEXDUMP=y
|
|
CONFIG_CMD_LOG=y
|
|
CONFIG_LOG_MAX_LEVEL=9
|
|
CONFIG_LOG_DEFAULT_LEVEL=9
|
|
CONFIG_LOGLEVEL=9
|
|
|