To maintain consistent behavior across architectures, most of the
options selected by ARCH_SUNXI should be selected for the D1 SoC as
well. To accomplish this, select them from BOARD_SUNXI instead.
No functional change here. Lines are only moved and alphabetized.
Signed-off-by: Samuel Holland <samuel@sholland.org>
With the introduction of the Allwinner D1, the sunxi board family now
spans multiple architectures (ARM and RISC-V). Since ARCH_SUNXI depends
on ARM, it cannot be used to gate architecture-independent options.
Specifically, this means the board Kconfig file cannot be sourced from
inside the "if ARCH_SUNXI" block.
Introduce a new BOARD_SUNXI symbol that can be selected by both
ARCH_SUNXI now and the new RISC-V SoC symbols when they are added, and
use it to gate the architecture-independent board options.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Some of the selected symbols have a user-visible dependency. Make the
selections conditional on that dependency to avoid creating invalid
configurations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Two of these selections are redundant and have no effect:
- DM_KEYBOARD is selected by USB_KEYBOARD
- DM_MMC is selected by MMC
This selection has no effect by default and is unnecessarily strong:
- USB_STORAGE is implied by DISTRO_DEFAULTS
Signed-off-by: Samuel Holland <samuel@sholland.org>
We tried to enable USB_EHCI_GENERIC and USB_OHCI_GENERIC by default.
This did not work because those symbols depend on USB_EHCI_HCD and
USB_OHCI_HCD, which were not enabled. Fix this by implying all four.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that Crust (SCP firmware) has support for H3, we need a FIT image to
load it. H3 also needs to load a SoC-specific eGon blob to support CPU 0
hotplug. Let's first enable FIT support before adding extra firmware.
Update the binman description to work on either 32-bit or 64-bit SoCs:
- Make BL31 optional, since it is not used on 32-bit SoCs (though BL32
may be used in the future).
- Explicitly set the minimum offset of the FIT to 32 KiB, since SPL on
some boards is still only 24 KiB large even with FIT support enabled.
CONFIG_SPL_PAD_TO cannot be used because it is not defined for H616.
FIT unlocks more features (signatures, multiple DTBs, etc.), so enable
it by default. A10 (sun4i) only has 24 KiB of SRAM A1, so it needs
SPL_FIT_IMAGE_TINY. For simplicity, enable that option everywhere.
Cover-letter:
sunxi: SPL FIT support for 32-bit sunxi SoCs
This series makes the necessary changes so 32-bit sunxi SoCs can load
additional device trees or firmware from SPL along with U-Boot proper.
There was no existing binman entry property that put the FIT at the
right offset. The minimum offset is 32k, but this matches neither the
SPL size (which is no more than 24k on some SoCs) nor the FIT alignment
(which is 512 bytes in practice due to SPL size constraints). So instead
of adding a new property, I fixed what is arguably a bug in the offset
property -- though this strategy will not work if someone is
intentionally creating overlapping entries.
END
Series-to: sunxi
Series-to: sjg
Signed-off-by: Samuel Holland <samuel@sholland.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the
SPL to build cache-pl310.c.
Before this commit, the SPL could enable the PL310 L2 cache [1], but the
cache maintenance functions from cache-pl310.c were only useable for
non-SPL builds.
After enabling the cache one must be able to flush it, too. Thus this
commit allows cache-pl310.c to be included in the SPL build.
[1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable()
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add GPIO registers structure for iMX93, so that we can enable lpgpio
driver
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ISW_ENTRY_ADDR symbol was used for OMAP devices in place of
SPL_TEXT_BASE. Keystone2 HS devices were not using it right either.
Remove ISW_ENTRY_ADDR and use SPL_TEXT_BASE directly.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
keystone doesn't have custom gpio.h that's why don't select
GPIO_EXTRA_HEADER which points to it.
Logic in arch/arm/include/asm/gpio.h is very clear
#ifdef CONFIG_GPIO_EXTRA_HEADER
#include <asm/arch/gpio.h>
#endif
#include <asm-generic/gpio.h>
Where it is visible that there is no gpio.h in platform headers:
$ ls arch/arm/mach-keystone/include/mach/
clock_defs.h clock-k2e.h clock-k2hk.h ddr3.h hardware-k2e.h
hardware-k2hk.h i2c_defs.h mon.h mux-k2g.h xhci-keystone.h
clock.h clock-k2g.h clock-k2l.h hardware.h hardware-k2g.h
hardware-k2l.h mmc_host_def.h msmc.h psc_defs.h
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The GXP is the HPE BMC SoC that is used in the majority
of current generation HPE servers. Traditionally the asic will
last multiple generations of server before being replaced.
Info about SoC:
HPE GXP is the name of the HPE Soc. This SoC is used to implement many BMC
features at HPE. It supports ARMv7 architecture based on the Cortex A9
core. It is capable of using an AXI bus to whicha memory controller is
attached. It has multiple SPI interfaces to connect boot flash and BIOS
flash. It uses a 10/100/1000 MAC for network connectivity. It has multiple
i2c engines to drive connectivity with a host infrastructure. There
currently are no public specifications but this process is being worked.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SPL is only supported by STM32MP15x not by all the
SOC with STM32MP arch.
Only TFABOOT is supported in next products.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
When this option is set then ARM _main() function would call
arch_very_early_init() function at the beginning. It would be before
calling any other functions like debug_uart_init() and also before
initializing C runtime environment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Janne Grunau <j@jannau.net>
Tested-by: Janne Grunau <j@jannau.net>
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
