Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/
Suggested-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Frequency changes to 400MHz are presently reported as:
lpddr4_set_rate_0: change freq to 400000000 mhz 0, 1
This is obviously wrong by 6 orders of magnitude.
Ensure frequency changes are reported accurately.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Functions pointed to by this op pointer can return non-zero values
indicating an error. Ensure any error value is propagated back up the
call-chain.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Only add the dram channel when we finally setup it successfully at the
last step.
Signed-off-by: Han Pengfei <pengphei@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the emulator assumes that the TPM is inited in the same phase
where it is used. But in fact SPL may init the TPM, so we don't want to
complain when U-Boot proper later uses it. Remove this check.
It might be best to save this information into the device state for the
TPM, so that we can make sure the TPM was inited at some point. For now,
this seems good enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The host will report such error message if the fastboot device work in
full-speed mode: "Duplicate descriptor for config 1 interface 0
altsetting 0, skipping"
Fastboot device ack both full and high speed interface descriptors when
work in full-speed mode, that's will cause this issue.
Fix it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: John Keeping <john@metanate.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The brute-force controller disable method can end up racing controller
initialization and causing a crash when we shut down Apple ANS2 NVMe
controllers. Do a proper controlled shutdown, which does block until
things are quiesced properly. This is nicer in general for all
controllers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Tested-by: Mark Kettenis <kettenis@openbsd.org> (firefly-rk3399)
PCIe config space has address range 0-4095. So do not allow reading from
addresses outside of this range. Lot of U-Boot drivers do not expect that
passed value is not in this range. PCI DM read function is extended to
fill read value to all ones or zeros when it fails as U-Boot callers
ignores return value.
Calling U-Boot command 'pci display.b 0.0.0 0 0x2000' now stops printing
config space at the end (before 0x1000 address).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Signed-off-by: Andrew Davis <afd@ti.com>
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Signed-off-by: Andrew Davis <afd@ti.com>
We don't need to print the same message in every location, just
print it in the function that fails and remove all the extra
message printouts.
Signed-off-by: Andrew Davis <afd@ti.com>
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since the base functionality remains the same for a reset driver on Qcom
SoCs, so leverage that to convert ipq4019 specific reset driver to a
generic Qcom reset driver. With that one just need to provide SoC specific
reset table.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Re-sync again on some linux part, add some fixes for fsl_elbc from
Pali and switch
imx8mn bsh to use nand base ident
For nand subsystem tested on:
- imx8mn Macronix MX30LF4G18AC
- P2020 based board Turris 1.1 for fsl_elbc
The gpio-button driver depends on DM_GPIO, add it to Kconfig to avoid
build errors.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Add timer support for Kirkwood and MVEBU devices.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
During compilation gcc throws warning:
drivers/mtd/nand/raw/fsl_elbc_nand.c: In function ‘fsl_elbc_nand_probe’:
drivers/mtd/nand/raw/fsl_elbc_nand.c:841:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return fsl_elbc_chip_init(0, (void *)dev_read_addr(dev), dev);
^
Fix it by using dev_read_addr_ptr() function which returns pointer instead
of dev_read_addr() which returns integer type.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Subpage write support for freescale eLBC NAND controller driver is
implemented in U-Boot and was fixes in the commit d3963721d93f ("nand: Sync
with Linux v4.1").
So remove NAND_NO_SUBPAGE_WRITE flag from the fsl_elbc_nand.c driver. This
partially revert commit cb04c7723429 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE
to eLBC and IFC drivers"), only eLBC driver part.
With this change U-Boot with default settings can read from NAND UBIFS
image created on Linux with Linux default settings. Prior this change
U-Boot was unable to read from NAND UBIFS images created with Linux default
settings due to differnet UBI geometry.
Linux kernel fsl_elbc_nand.c driver also does not set NAND_NO_SUBPAGE_WRITE
flag and has implemented subpage write support.
Fixes: cb04c7723429 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers")
Fixes: d3963721d93f ("nand: Sync with Linux v4.1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-By: Michael Trimarchi<michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8fc82d456e40a0.
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7bb427990ee364.
Rename the function to match this new behavior.
NOTE: fix nand_detect/nand_get_flash_type parameters in
mxs_nand_spl. This code seems never executed by any board
as alternative for nand detect
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 4722c0e958e636.
The returned "type" is never used in nand_scan_ident() and spl code
Make nand_get_flash_type() simply return an integer value in order
to avoid unnecessary ERR_PTR/PTR_ERR dance.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8cfb9ab68f9070.
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
When using DM_ETH, which should be the default now, we need to always
have DM_MDIO and FSL_LS_MDIO enabled, so select them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Wasim Khan <wasim.khan@nxp.com>
Cc: Udit Agarwal <udit.agarwal@nxp.com>
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Manish Tomar <Manish.Tomar@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver has not been converted to DM_ETH. The migration
deadline passed 2 years ago.
Cc: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
In generally it is not permitted to implement an ofnode function only for
flat tree or live tree. Both must be supported. Also the code for
live tree access should be in of_access.c rather than ofnode.c which is
really just for holding the API-conversion code.
Update ofnode_write_prop() accordingly and fix the test so it can work
with flat tree too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these to VESA, itself an abbreviation, to avoid a conflict with
Verified Boot for Embedded.
Rename this to avoid referencing VBE.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
