The USB Power domains should not have been removed as it causes
the board to hang if the USB is started.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Bitwise operations on signed integers are not defined,
replace them with per-call checks.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
add support for SHA-256 secure hash algorithm using the ARM v8
SHA-256 instructions for verifying image hash.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Abstract common interfaces for AHAB authentication operations.
Then share some common codes for AHAB and SPL container authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If the container has image which conflicts with
spl_get_load_buffer address, there are processing failures.
Use malloc instead of spl_get_load_buffer.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Implement bootaux for the M4 boot on i.MX8QM and QXP. Users need to download
M4 image to any DDR address first. Then use the
"bootaux <M4 download DDR address> [M4 core id]" to boot CM4_0
or CM4_1, the default core id is 0 for CM4_0.
Since current M4 only supports running in TCM. The bootaux will copy
the M4 image from DDR to its TCML.
2. Implment bootaux for HIFI on QXP
command: bootaux 0x81000000 1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The bootaux uses ulong to read private data and write to M4 TCM,
this cause problem on ARM64 platform where the ulong is 8bytes.
Fix it by using u32 to replace ulong.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix below coverity issues caused by get_idx function where "-1" is
compared with uint8_t "element"
343336 Unsigned compared with neg
343337 Operands don't affect result
Additional, this function returns "-1" will cause overflow to
event string array.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity (CID 21143558).
When tee_shm_register returns failure, the shm_input pointer is
invalid, should not free it. Same issue also exists on registering
shm_output.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the
t1024rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the
t1042d4rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the t4240rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the serial node descriptions similar to Linux v6.4 for the t2080rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint ipi driver to
support ACLINT mswi device, by checking the per-driver data field of
the ACLINT mtimer driver to determine whether a syscon based approach
needs to be taken to get the base address of the ACLINT mswi device.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
StarFive VisionFive 2 has two versions, 1.2A and 1.3B, each version of
DDR capacity includes 2G/4G/8G, a DT can not support multiple
capacities, so the capacity size information is recorded to EEPROM, when
DDR initialization required capacity size information is read from
EEPROM.
If there is no information in EEPROM, it is initialized with the default
size defined in DT.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support "atmel,24c04" eeprom for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between 1.2A and 1.3B is dynamically configured according
to the PCB version, and there is no difference on the board device tree,
so the same DT file can be used.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add ethernet device tree node to support StarFive ethernet driver for
the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
