This patch adds pwm channel 2 (pwm3) support for mt7981
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Explicitly add quad mode capabilities or the SPI controller may
start transfer in single mode.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10s/A13 SoCs (sun5i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10s/A13 related .dts and .dtsi files, and
switch most of sun5i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10 SoCs (sun4i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10 related .dts and .dtsi files, and switch
most of sun4i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner F1C100/F1C200 SoCs (sunvi) between the U-Boot
and the Linux kernel repository.
Remove the old copies of the F1Cx00 related .dts and .dtsi files, and
switch the whole suniv SoC over to use OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series migrates MediaTek MT7629 to OF_UPSTREAM
Changes in v2:
* Remove mt7629-rfb.dtb from arch/arm/dts/Makefile
* Add wdt-reboot node to make reset command work
Link: https://lore.kernel.org/r/cover.1736851116.git.weijie.gao@mediatek.com
david regan <dregan@broadcom.com> says:
Updates for Broadcom bcmbca devices,
make use of OF_UPSTREAM which uses Linux dts,
update bcmbca dts to current nand node naming convention,
enable basic nand functionality for bcmbca devices.
Link: https://lore.kernel.org/r/20250114045425.148801-1-dregan@broadcom.com
Add defconfig & devicetree for IBM SBP1 board BMC based on AST2600 SoC.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Move differences in DT files between upstream Linux DT and U-Boot DT to
mt7629-rfb-u-boot.dtsi.
Remove old copies of mt7629-related clock bindings, .dts, and .dtsi files.
Update defconfig to switch the whole mt7629 SoC to use OF_UPSTREAM.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Update bcmbca dts to current nand node naming convention.
Changes in v2:
- Removed addition of nand-on-flash-bbt parameter
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
Make use of OF_UPSTREAM which uses Linux dts.
Changes in v2:
- Removed enabling of nand functionality
Signed-off-by: david degan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
Guard binman nodes with CONFIG_OPTEE to fix the following error
when building without optee support:
BINMAN .binman_stamp
Image 'image' has faked external blobs and is non-functional: tee.bin
Image 'image' is missing optional external blobs but is still functional: tee-os
/binman/section/fit/images/tee/tee-os (tee.bin):
See the documentation for your board. You may need to build Open Portable
Trusted Execution Environment (OP-TEE) and build with TEE=/path/to/tee.bin
Some images are invalid
make: *** [Makefile:1135: .binman_stamp] Error 103
While at it, only pass tee to the loadables lines when CONFIG_OPTEE is
defined.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Yannic Moog <y.moog@phytec.de>
Most R-Car Gen3 and Gen4 systems require extalr_clk very early
in the boot process. Currently the extalr_clk { bootph-all } DT
property to indicate this clock should be available early is set
in each SoC U-Boot DT extras file. Deduplicate this assignment to
new common r8a779x-rcar64-u-boot.dtsi file.
Note that R-Car Gen3 R8A77990 E3 and R8A77995 D3 and RZ R8A774C0
do not require extalr_clk early, therefore these SoCs still include
plain r8a779x-u-boot.dtsi in their U-Boot DT extras .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add tee node in SoC u-boot device trees. Use a kconfig entry to specify
load and entry addresses for the op-tee image in the respective
defconfig.
Default IMX8M_OPTEE_LOAD_ADDR is supplied. To keep it simple, the same
addresses are used for each SoC as are defined in upstream tf-a
(BL32_BASE) [1].
[1] https://github.com/ARM-software/arm-trusted-firmware/tree/master/plat/imx/imx8m
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Add ss_cfg memory region which maps the DDRSS configuration region
for the memory controller node.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Neha Malcom Francis <n-francis@ti.com>
Raymond Mao <raymond.mao@linaro.org> says:
Motivations for changes:
Current SMBIOS library and command-line tool is not fully matching with
the requirements:
1. Missing support for other mandatory types (#7, #9, #16, #17, #19).
2. Only a few platforms support SMBIOS node from the device tree.
3. Values of some fields are hardcoded in the library other than fetching
from the device hardware.
4. Embedded data with dynamic length is not supported (E.g. Contained
Object Handles in Type #2 and Contained Elements in Type #3)
Changes:
1. Refactor the SMBIOS library and command-line tool to better align with
the SMBIOS spec.
2. Create an arch-specific driver for all aarch64-based platforms to fetch
SMBIOS private data from the device hardware (processor and cache).
3. Create a sysinfo driver to poppulate platform SMBIOS private data.
4. Add generic SMBIOS DTS file for arm64 platforms for those common strings
and values which cannot be retrieved from the system registers.
Vendors can create their own SMBIOS node using this as an example.
For those boards without SMBIOS nodes, this DTS file can be included to
have a generic SMBIOS information of the system.
5. Add support for Type #7 (Cache Information) and link its handles to
Type #4.
6. To minimize size-growth for those platforms which have not sufficient
ROM spaces or the platforms which don't need detailed SMBIOS
information, new added fields are only being built when kconfig
GENERATE_SMBIOS_TABLE_VERBOSE is selected.
Once this patch is acceptted, subsequent patch sets will add other missing
types (#9, #16, #17, #19).
Tests:
To test this with QEMU arm64, please follow the guide on dt_qemu.rst to
get a merged DT to run with.
```
qemu-system-aarch64 -machine virt -machine dumpdtb=qemu.dtb
cat <(dtc -I dtb qemu.dtb) <(dtc -I dtb ./dts/dt.dtb | grep -v /dts-v1/) \
| dtc - -o merged.dtb
qemu-system-aarch64 -machine virt -nographic -bios u-boot.bin \
-dtb merged.dtb
```
Link: https://lore.kernel.org/r/20241206225438.13866-1-raymond.mao@linaro.org
Add common smbios information that can be used by all armv8
platforms and set it as default for qemu-arm64.
>From now smbios library can load values from here for those fields
doesn't exist in the sysinfo driver.
To run this with QEMU arm64, we need to dump the generated DTB
from QEMU first, merge it with the one we build and then re-run
QEMU with the merged DTB.
```
qemu-system-aarch64 -machine virt -machine dumpdtb=qemu.dtb
cat <(dtc -I dtb qemu.dtb) <(dtc -I dtb ./dts/dt.dtb | \
grep -v /dts-v1/) | dtc - -o merged.dtb
qemu-system-aarch64 -machine virt -nographic -bios u-boot.bin \
-dtb merged.dtb
```
For details please take reference on dt_qemu.rst
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Replace underscores with hyphens in the clock node names as per
dt-schema rule.
Also, add clock-output-names property to all clock nodes, so that the
resulting clock name do not change when clock node name is changed.
Signed-off-by: Naman Trivedi <naman.trivedimanojbhai@amd.com>
Acked-by: Senthil Nathan Thangaraj <senthilnathan.thangaraj@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1080e31393c3e1b49735b77e7ddc14d570b83222.1733991159.git.michal.simek@amd.com
Implement checkboard() to print current SoC model used by a board,
e.g. one of:
SoC: RK3582
SoC: RK3588
SoC: RK3588J
SoC: RK3588S
SoC: RK3588S2
when U-Boot proper is running.
U-Boot 2025.01-rc1 (Nov 10 2024 - 00:31:29 +0000)
Model: Generic RK3588S/RK3588
SoC: RK3588S2
DRAM: 8 GiB
Information about the SoC model and variant is read from OTP.
Also update rk3588s-u-boot.dtsi to include OTP in U-Boot pre-reloc phase,
where checkboard() is called.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Implement checkboard() to print current SoC model used by a board,
e.g. one of:
SoC: RK3566
SoC: RK3566T
SoC: RK3568
SoC: RK3568B2
SoC: RK3568J
when U-Boot proper is running.
U-Boot 2025.01-rc1 (Nov 10 2024 - 00:39:37 +0000)
Model: Generic RK3566/RK3568
SoC: RK3568J
DRAM: 8 GiB (effective 7.7 GiB)
Information about the SoC model and variant is read from OTP.
Also update rk356x-u-boot.dtsi to include OTP in U-Boot pre-reloc phase,
where checkboard() is called.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 7cec3e701940 ("rockchip: rk3588-nanopc-t6: Add support for
NanoPC-T6 LTS") added support for the LTS variant of NanoPC T6. However,
a board specific -u-boot.dtsi file was never added.
Due to the missing -u-boot.dtsi file the LTS fdt included in the FIT is
never tagged with bootph props.
When ENV_IS_IN_SPI_FLASH is enabled, not enabled in defconfig, the env
can successfully load from SPI flash on the non-LTS variant, something
that does not work on the LTS variant due to missing bootph-some-ram
props in the LTS fdt.
Fix this by adding a LTS -u-boot.dtsi file that just include the non-LTS
-u-boot.dtsi file.
Reported-by: Ricardo Pardini <ricardo@pardini.net>
Fixes: 7cec3e701940 ("rockchip: rk3588-nanopc-t6: Add support for NanoPC-T6 LTS")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include vital
regulators in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The eMMC PHY and SPI flash is not used in all xPL phases.
Change to no longer include emmc_phy and spi_flash in all xPL phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The u-boot.rom image contain u-boot.img FIT instead of the FIT generated
by binman for the u-boot-rockchip.bin image.
Change to include the binman generated FIT for the u-boot.rom image.
This change result in TF-A being included and the use sha256 instead of
crc32 checksum in the u-boot.rom FIT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The chromebook specific u-boot.rom image does not include TPL when
building with TPL=y or ROCKCHIP_EXTERNAL_TPL=y.
Fix this by adding rockchip-tpl and u-boot-tpl nodes to the mkimage node
for the u-boot.rom binman image.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the offset configured with SYS_SPI_U_BOOT_OFFS Kconfig option
instead of a hardcoded 0x40000 for the FIT payload offset.
This has no intended impact as SYS_SPI_U_BOOT_OFFS=0x40000.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3066a/rk3188 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3066a/rk3188 boards.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa ROCK 5C[1] is a Rockchip RK3588S2 based single board computer.
[1] https://radxa.com/products/rock5/5c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPi R3S(as "R3S") is an open source platform with dual-Gbps
Ethernet ports designed and developed by FriendlyElec for IoT
applications.
Specification:
- Rockchip RK3566
- 2GB LPDDR4X RAM
- optional 32GB eMMC module
- SD card slot
- 2x 1000 Base-T
- 3x LEDs (POWER, LAN, WAN)
- 2x Buttons (Reset, MaskROM)
- 1x USB 3.0 Port
- Type-C 5V 2A Power
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
Firefly-RK3288 use RTL8211 Ethernet PHY, datasheet list an initial 10ms
delay and then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for Firefly-RK3288 in dts/upstream can be used as-is by
U-Boot, migrate board to use OF_UPSTREAM.
Add chosen stdout-path prop to board u-boot.dtsi as it is missing in DT
from dts/upstream. Also change to use the upstream power_led symbol.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include mmc related nodes in U-Boot proper pre-reloc phase to ensure
environment can be loaded from mmc devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The sdmmc power come from vcc33_sd pmic regulator and not from the
vcc_sd fixed regulator, as currently defined in the in-tree DT.
Drop vcc_sd and the related gpio7 and sdmmc_pwr nodes from being
included in SPL along with any related Kconfig option. Also enable
SPL_DM_SEQ_ALIAS to ensure aliases is handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include the sdmmc
regulator in SPL. Also enable SPL_DM_SEQ_ALIAS to ensure aliases is
handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop the unneeded bootph-all prop from dmc node, it is already defined
in soc u-boot.dtsi.
Remove booth-all prop from gpio7 node, this node is not needed in TPL.
Adjust bootph props to include pinctrl related nodes for UART2.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph- props to emmc, sdmmc, uart and related pinctrl nodes to
ensure devices and pinctrl can be used in xPL and U-Boot pre-reloc.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort the nodes in rk3288-tinker u-boot.dtsi files in alphabetical order.
This has no intended change to board DTs and only rearrange nodes in
preparation for future changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vop nodes does not need to be included in xPL control FDT, they only
need to be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort the nodes in rk3288-firefly-u-boot.dtsi in alphabetical order.
This has no intended change to board DT, this only rearrange nodes in
preparation for future changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288.dtsi from arch/arm/dts is almost identical to the rk3288.dtsi
from dts/upstream, it differs only with a minor change in hdmi port
nodes, something that does not affect U-Boot.
Remove arch/arm/dts/rk3288.dtsi to use rk3288.dtsi from dts/upstream.
Also drop gpio aliases from -u-boot.dtsi that has been part of
rk3288.dtsi for some time.
No functional change to board DTs is intended with this removal.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The firefly-rk3288_defconfig build target does not enable the SPL_LED
Kconfig option.
Drop the unused SPL_LED related code and replace it with a default-state
prop to ensure the LED driver enable the LED at U-Boot proper phase.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The reset mechanism used by Linux to reset the SoC is known to only
partially reset the logic. A mechanism is implemented in
rk3399_force_power_on_reset to use a GPIO connected to the PMIC's
over-temperature (OTP) reset pin, which fully resets all logic.
Hook the associated GPIO where the function expects it to enable this
reset mechanism and avoid any possible side-effect of partially-reset
units.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The reset mechanism used by Linux to reset the SoC is known to only
partially reset the logic. A mechanism is implemented in
rk3399_force_power_on_reset to use a GPIO connected to the PMIC's
over-temperature (OTP) reset pin, which fully resets all logic.
Hook the associated GPIO where the function expects it to enable this
reset mechanism and avoid any possible side-effect of partially-reset
units.
Without this patch, reading from the micro sd slot fails after a reset.
With this mechanism, U-Boot is able to boot from it reliably.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
MiQi use RTL8211 Ethernet PHY, datasheet list an initial 10ms delay and
then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
