All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600d4 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Raymond Mao <raymond.mao@linaro.org> says:
This patch set is picked from the previously posted serie:
"[RFC] Integrate MbedTLS v3.6 LTS with U-Boot"
They are not directly related to MbedTLS integration, but the
prerequisite for a few clean-up, refactoring and minor fixes.
For V2, the linker script patch is dropped and added one patch
to move the snprintf to stdio.h
Move snprintf to stdio.h since it is needed by exteranl libraries.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Roger Quadros <rogerq@kernel.org> says:
Sync AM62 device tree files with Linux v6.9 and
add in the missing bits in -u-boot.dtsi to get CPSW
Ethernet working.
CI testing: https://github.com/u-boot/u-boot/pull/534
Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add defconfig for AM68 SK R5 and A72 configuration.
This includes and modifies the AM68 EVM defconfigs:
j721s2_evm_r5_defconfig -> am68_sk_r5_defconfig
j721s2_evm_a72_defconfig -> am68_sk_a72_defconfig
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Create an SoC R5 dtsi file that could be used at board level R5 files. This
would help in keeping the SoC level changes in sync across board files.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Currently AM68 SK boots with J721s2 R5 DTS and then later changes to
AM68 SK DT during runtime.
To split the support of J721s2 and AM68, sync AM68 R5 DT with J721s2 R5
DT as that contains some essential node changes for booting up AM68
using AM68 R5 DT.
secure_proxy_sa3 and secure_proxy_mcu node changes are required for
establishing contact with ROM and TIFS running on SMS M4 core,
respectively, and the addition of new power domain helps in holding A72
cluster in reset for configuration of firewalls.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Martyn Welch <martyn.welch@collabora.com> says:
This series adds DFU support for TI AM62 SK and beagleplay boards.
I have picked this series up from Sjoerd due to time constraints.
Since the last revision:
* Removed dwc3 mode setting in favour of reinstating forced peripheral
mode for usb0
* Use of config fragments for both r5 and a53 DFU configuration to
reduce duplication
* Typographical improvements to documentation
We plan to also submit the dts changes to linux so that those can be
dropped again in the near future (hopefully)
DFU mode on a beagleplay can be used via the Type-C connector by holding
the USR switch while powering on.
Configuration is already provided as fragments for both the A53 and R5
u-boot parts. Include the am62x_a53_usbdfu.config config. The
am62x_r5_usbdfu.config fragment needs to be added should DFU boot be
required as this will disable booting from persistent storage due to
binary size constraints.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Enable usb0 in all boot phases for use with DFU
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This [pull request] for master fixes framebuffer video on almost all
Qualcomm platforms where the framebuffer is initialised by the first
stage bootloader.
* We already have a header 'backtrace', there is no need to repeat the
word backtrace on every line.
* Add a blank line before the backtrace section of the crash report for
improved readability.
* If U-Boot is compiled without backtrace, there is no need to write a
message at all.
* Avoid #ifdef. We prefer functions to always be compiled and let
the linker remove them if not needed.
* Foresee 3 digits for the backtrace index.
For testing the 'exception' command can be used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The EEPROM provides information about the size of the eMMC.
Provide a new function get_mmc_size_from_eeprom() to read it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
The newly introduced carve_out_reserved_memory causes issues when
U-Boot is chained from the lk2nd bootloader. lk2nd provides a
simple-framebuffer device and marks the framebuffer region as no-map in
the supplied /reserved-memory. Consequently, the simple_video driver
triggers a page fault when it tries to write to this region.
As per Caleb's advice, this simple patch only does the carveouts for the
qcs404 SoC for which it was originally designed. The intent is to do the
carveouts for more Qualcomm SoCs in future.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Polling cntpct_el0 in a tight loop for delays is inefficient.
This is particularly apparent on Arm FVPs, which do not simulate
real time, meaning that a 1s sleep can take a couple of orders
of magnitude longer to execute in wall time.
If running at EL2 or above (where CNTHCTL_EL2 is available), enable
the cntpct_el0 event stream temporarily and use wfe to implement
the delay more efficiently. The event period is chosen as a
trade-off between efficiency and the fact that Arm FVPs do not
typically simulate real time.
This is only implemented for Armv8 boards, where an architectural
timer exists, and only enabled by default for the ARCH_VEXPRESS64
board family.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The sev() and wfe() asm macros are currently defined only for
mach-exynos. As these are common Arm instructions, move them to the
common asm/system.h header file, for both Armv7 and Armv8, so they
can be used by other machines.
wfe may theoretically trigger a context switch if an interrupt occurs
so add a memory barrier to this call.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara<andre.przywara@arm.com>
Roger Quadros <rogerq@kernel.org> says:
Sync AM62 device tree files with Linux v6.9 and
add in the missing bits in -u-boot.dtsi to get CPSW
Ethernet working.
CI testing: https://github.com/u-boot/u-boot/pull/534
Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
On all Raspberry Pi platforms, we're loaded by a prior stage firmware
that has assembled and passed on a device tree binary for us to use.
Switch to using this tree by default.
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: François Ozog <francois.ozog@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Remove DTs which are now replaced by OF_UPSTREAM counterparts.
No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com> #beacon boards
Let's provide get_boot_device() for AM64, similar to what we did
in commit 2f9095e2bf59 ("arm: mach-k3: am625: Provide a way to obtain boot
device for non SPLs") for AM62.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
J7200 has SR1.0 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-SE SR1.0 and HS-FS SR1.0 so
add support for them.
Reported-by: Suman Anna <s-anna@ti.com>
Reported-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
J721E has SR1.1 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-FS SR1.1 so add support for
them.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
The DM37 and OMAP35 SOM-LV share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
The DM37 and OMAP35 Torpedo share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
With the feature of OF_UPSTREAM now available, the device trees
for the SOM and baseboard can now deleted and the device tree
locations need to point to the ti/omap directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT reference from Makefile.
The da850-evm can remove the U-Boot device trees if migrated
to OF_UPSTREAM. This means pointing the device trees to the
ti/davinci directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
v2: Remove DTS from Makefile.
