The signal integrity test generates pattern on DDR lines
for certification. The signals must be as fast as possible
and unidirectional.
The test is required from our HW team. The available
u-boot memory test doesn't full fill the our requirements.
The test is planed to be used in all new siemens boards.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add siemens specific memory test. Enable it through Kconfig option
SPL_CMT. The test is required from our HW team. It runs over
temperature during many days:
* must run indefinitively through the *whole* DDR area,
so we cannot use linux memtest for example.
* must write/read/check all values
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
The eeprom contains the information on which module
we are running, so read it from the eeprom and print
it on the console.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Get the memory region information from system controller to reduce the
number of platform specific headers. We were aligned on NXP mek board
implementation. This need at least 1 header per memory configuration.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add the HW version read directly from EEPROM.
EEPROM chip data structure is now in a .h file common to draco
and capricorn.
Therefore move out the definitions in draco board to siemens
common place.
From: Alessandro Zini <alessandro.zini@siemens.com>
Signed-off-by: Alessandro Zini <alessandro.zini@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
with newest SCFW build_info() works now, so call it
from checkboard() now.
As we only use uart2 as console, do not init uart0.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Boards which use DCD data in SCFW can drop SPL.
We tried in our mainline rework to use this approach
too as other imx8qxp boards do in mainline. But we
failed ... it was a hard way to understand the
reason!
We cannot use DCD image in container as the SCFW
from siemens, does the RAM init on boot itself!
Siemens SCFW reads the RAM config from i2c eeprom and
dependent on this settings, initializes the RAM.
Adding DCD data to the bootcontainer will result in
hang of the SCFW, also DCD data in container image is
static which do not fit our needs.
So we must drop DCD data image, and this has the side
effect that we need SPL, as the task which loads the images
from the container only loads the images to addresses,
and if executed bit is set, starts them.
As now RAM is not initialized from it, and there is no
option to "wait until SCFW has setup RAM", we can only
load SPL into internal RAM at this point, as than SPL
and SCFW boot parallel.
The SPL itself then uses the SCU API to communicate
with the SCFW and it seems that SCFW only responds to
this API requests when RAM setup is already done by the
SCFW, which has a side-effect of a "sync" for the RAM
setup is done by SCFW!
We checked if SPL is always save in accessing RAM for
loading images to it! For tests, we added in our RAM
init part in the SCFW long delays (10 seconds and more)
as we thought there is such a sync missing, and we can
break the board through delaying RAM setup... but we
did not managed to fail booting U-Boot from SPL!
Signed-off-by: Heiko Schocher <hs@denx.de>
We have many HW with capricorn i.MX8X boards. The difference in u-boot is
at all by the display of the LEDs.
* put upstream a reference project & board for DT and defconfig
* use the capricorn prefix outside the board/siemens/capricorn folder
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
probing on capricorn board (imx8qxp based) brings:
Can't find FEC0 clk rate: -19
Cause is that when probing fec_mxc driver, fec_mii_setspeed()
is called which calls fec_get_clk_rate().
fec_mii_setspeed() calls fec_get_clk_rate with NULL pointer
for udev and so as in IMX8QXP case CLK_CCF is enabled
udev gets searched with:
uclass_get_device_by_seq(UCLASS_ETH, idx, &dev);
but we do not have yet a UCLASS_ETH ! as we just probing it!
Prevent this by passing udev to fec_get_clk_rate()
Signed-off-by: Heiko Schocher <hs@denx.de>
The previous maintainer is no longer involved in total compute.
Signed-off-by: Ben Horgan <ben.horgan@arm.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
There is no common symbol which mini configurations are using and recent
get_mem_top() changes adding 1.3kB without having a way to remove it.
That's why introduce new symbol which can be used for removing features
which are not requested by these configurations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aa27b72e17057fa8cbdd92a2bbb863a31c8c1226.1731681053.git.michal.simek@amd.com
We are about to add a large number of new entries. Update the prefix to
be a little shorter.
For SMBIOS items, use SYSID_SM_ (for System Management) which is enough
to distinguish it. For now at least, it seems that most items will be
for SMBIOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Raymond Mao <raymond.mao@linaro.org>
Use the get_mem_top function to compute the value of ram_top. This was
earlier done through LMB API's, which are no longer available till
after relocation. Use get_mem_top() instead to compute the ram_top
value.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20241025172724.195093-3-sughosh.ganu@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
Wadim Egorov <w.egorov@phytec.de> says:
Our SoMs are available in multiple configurations, managed via device
tree overlays. To determine the specific variant in use, we read the
EEPROM and apply the appropriate overlays during boot to the device tree
used by the OS.
Apply overlays for phyCORE-AM62x and phyCORE-AM64x SoMs.
Future K3 SoMs will be able to reuse this logic and overlays.
Link: https://lore.kernel.org/r/20241030164815.1763506-1-w.egorov@phytec.de
Our SoMs are available in multiple configurations, managed via device
tree overlays. To determine the specific variant in use, we read the
EEPROM and apply the appropriate overlays during boot to the device tree
used by the OS.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Neha Malcom Francis <n-francis@ti.com>
qemu_arm64_defconfig with CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=n leads to a
build error:
arch/arm/lib/crt0_64.S:85:
Error: constant expression expected at operand 2 --
`ldr x0,=((CFG_SYS_INIT_RAM_ADDR+CFG_SYS_INIT_RAM_SIZE-480))'
We do not define CFG_SYS_INIT_RAM_ADDR and CFG_SYS_INIT_RAM_SIZE for QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FriendlyElec NanoPi R2S Plus is a single-board computer based on
Rockchip RK3328 SoC. It features e.g. 1 GB DDR4 RAM, 32 GB eMMC,
SD-card, 2x GbE LAN, optional M.2 SDIO Wi-Fi and 2x USB 2.0 host.
Features tested on a NanoPi R2S Plus 2309:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For upstream Linux kernel we use below DTBs for HiHope boards:
- r8a774a1-hihope-rzg2m-ex.dtb
- r8a774e1-hihope-rzg2h-ex.dtb
- r8a774b1-hihope-rzg2n-ex.dtb
Update the CONFIG_OF_LIST to match the above. Now that we have switched
upstream DTS, drop deleting the nodes and also rename the
r8a774*-u-boot.dtsi files to r8a774*-ex-u-boot.dtsi to match the OF_LIST
files so that the `bootph-all` property gets applied to required nodes
in upstream DTS.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
We are now using the dts/upstream subtree for the RZ/G2L SoC family, so
update the board MAINTAINERS file to match rz-smarc dtsi files in this
subtree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Improve "mmcautodetect=yes" boot mode autodetection to able to use it
if CONFIG_ENV_IS_NOWHERE=y is used for i.MX9 SoCs and i.MX93 EVK board.
If both CONFIG_ENV_IS_IN_MMC=y and CONFIG_ENV_IS_NOWHERE=y are in the
defconfig, CONFIG_ENV_IS_IN_MMC=y will be overiden default
CONFIG_ENV_IS_NOWHERE settings.
Goal is in this patch to able to use the boot mode autodetection
if defconfig use only CONFIG_ENV_IS_NOWHERE=y option
(without CONFIG_ENV_IS_IN_MMC) for any i.MX9 SoC.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
DTB should be also placed to DDR. It should be the part of commit
9d688e6da5c9 ("riscv: mbv: Align DT with QEMU").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Leo Yan <leo.yan@arm.com> says:
This patch series is to refine the booting on Arm Total Compuate
platform.
It changes to use the info passed in DTB for initialization DRAM info,
and dynamically initializes the booting envoironment variables.
Another big change is to use an envoironment file for boot commands,
based on it, the series extends to support multiple block devices
(MMC and virtio). And the env file is extended for booting Debian.
The last commit is to update memory mapping info based on the DRAM info
passed via DT binding.
Link: https://lore.kernel.org/r/20241025171821.624702-1-leo.yan@arm.com
This commit introduces build_mem_map() function for updating the mem_map
structure with copying info from gd->bd->bi_dram, so that it can keep
the consistence for DRAM info passed via DT.
The page table size is calculated prior to mem_map is ready, introduce
the get_page_table_size() function for a predefined table size.
Signed-off-by: Leo Yan <leo.yan@arm.com>
Dynamically detect block device in the boot command, this allows to
support both MMC and virtio block devices.
Signed-off-by: Leo Yan <leo.yan@arm.com>
The boot command for Total Compute has many aspects and changes from time
to time. So move it to an .env file where it can be a proper script.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Create an SoC R5 dtsi file that could be used at board level R5 files. This
would help in keeping the SoC level changes in sync across board files.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Bastien Curutchet <bastien.curutchet@bootlin.com> says:
Hi all,
This patch series aims to add DM support for the AEMIF controller that
can be found in the DaVinci SoCs.
This controller has already a driver used by the Keystone SoCs so I
add my work to it.
As we can now easily import Linux device-trees, I try to stick the
most I can to the Linux bindings of the AEMIF controller. To do so I add
an 'intermediate' driver called 'ti-aemif-cs'. It's in charge of
configuring timings for a given chip select of the AEMIF controller.
Link: https://lore.kernel.org/r/20241021151330.1860929-1-bastien.curutchet@bootlin.com
AEMIF controller is present on other SoCs than the Keystone ones.
Remove Keystone specificities from the driver to be able to use it from
other architectures.
Adapt the ks2_evm/board.c to fit the new driver.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is tailored down. Instead, to communicate with the
PLC 1200 signal modules, a USB 3.0 type B connector is added but the
signal is not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebased over OF_UPSTREAM]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The clock driver for PolarFire SoC now requires syscon and regmap
features, so imply them to preserve implication of the clock driver.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
