The RK35xx SoCs contain a crypto engine block that can generate random
numbers.
Enable rng node in soc u-boot.dtsi and enable Kconfig options to take
advantage of the random generator.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPL_ROCKCHIP_BACK_TO_BROM should normally only be enabled when BROM
should load U-Boot binary. SPL on Anbernic RGxx3 devices load TF-A and
U-Boot proper from FIT images and does never jump back to BROM from SPL.
Remove the superfluous Kconfig option from defconfig to align with other
RK356x boards.
This patch have no intended change in boot behavior.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588 boards do not have any pwm-regulator compatible nodes in DT, drop
the superfluous REGULATOR_PWM Kconfig options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3308-rock-pi-s with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Also fix use of USB 2.0 otg port by removing improper use of phy-supply
and regulator-always-on props.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3308-roc-cc with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3308-evb with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Use DEBUG_UART_BASE=0xFF0E0000 and disable DEBUG_UART_BOARD_INIT to
make debug uart use uart4, same as stdout-path prop.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3308 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 16 2024 - 12:36:12 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Imply SPL_PINCTRL and SPL_DM_SEQ_ALIAS to apply correct pinconf before
trying to load FIT from a device.
Move u-boot,spl-boot-order to soc u-boot.dtsi and define both sdmmc and
emmc nodes as fallback.
Also fix boot from eMMC (SD NAND) on ROCK Pi S by using correct pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3308 SoC support ARMv8 Cryptography Extensions and use of the
ARMv8 crypto extensions help speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation on all RK3308 boards.
Also disable CONFIG_SPL_RAW_IMAGE_SUPPORT in board defconfigs to ensure
SPL does not try to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Support is added for 5 new Qualcomm SoCs:
* QCM2290 and SM6115 are low and mid range SoCs used on the RB1 and RB2
respectively. SM6115 is also used in some mid-range smartphones/tablets.
Initial support includes buttons and USB (host and gadget).
* SM8250 is a flagship SoC from 2020 used on the RB5, as well as many flagship
smartphones. The board can boot to a U-Boot prompt, but is missing regulators
necessary for USB support.
* SM8550, and SM8650 are flagship mobile SoCs from 2023 and 2024
respectively. Found on many high end smartphones.
In addition:
* Support is added for the Schneider HMIBSC board.
* mach-snapdragon switches to OF_UPSTREAM
* IPQ40xx gets several regressions fixed and some overall cleanup.
* The MSM serial driver gains the ability to generate the bit-clock
automatically, no longer relying on a custom DT property.
* The Qualcomm SMMU driver gets a generic compatible (so per-SoC compatibles
don't need to be added).
* Support for the GENI I2C controller is added.
* The qcom SPMI driver has SPMI v5 support fixed, and v7 support added.
* The qcom sdhci driver gets some fixes for SDCC v5 support.
* SDM845 gains sdcard support
* Support is added for the Synopsys eUSB2 PHY driver (used on SM8550 and SM8650)
* SYS_INIT_SP_BSS_OFFSET is set to 1.5M to give us more space for FDTs.
* RB2 gets a work-around to fix the USB dr_mode property before booting Linux.
Use the new device devicetree files in dts/upstream/ and delete the old
ones. Still keep the -u-boot.dtsi with all u-boot specifics around.
There is one catch and that is fsl-ls1028a-kontron-sl28-var3.dts which
is not available upstream (yet!). For now, the base dts is used for this
variant as this only differ in the compatible and the (human readable)
model name.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
EFI initialisation fails without this, and with proper SMBIOS v3 support
in (and automatic generation of useful tables) there's no reason for us
not to do this on qcom platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Defining this as 0 results in bootm causing a null pointer exception...
Define it at a safe default which is valid RAM on most qcom boards.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Give us lots of room for the appended FDT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Switch to using upstream DT from dts/upstream.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable the clock and pinctrl drivers for qcm2290, sm6115, and sm8250.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Janne Grunau <j@jannau.net> says:
This series contains a few misc config changes for Apple silicon
systems:
- switch from the deprecated distro boot scripts to standard boot
- allows EFI console resizing based on the video console size
- enables 16x32 bitmap fonts as Apple devices come with high DPI
displays
- enables 64-bit LBA addressing
The bootflow list is only seen briefly and is probably more confusing
than helpful.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Apple devices have high DPI displays so the larger fonts are preferable
for improved readability. This does not yet change the used font based
on the display's pixel density so the standard 8x16 font is still used
by default.
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
This makes USB HDDs >2TiB work. The only reason this hasn't bitten us
for the internal NVMe yet is the 4K sector size, because the largest SSD
Apple sells is 8TB and we can handle up to 16TiB with that sector size.
Close call.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
Of all T30 transformers, only the TF600T uses SPI flash and
needs SLINK driver to work with it. Move this configuration
to the tf600t fragment from common defconfig.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
CONFIG_SYS_L2CACHE_OFF is not affecting these devices in any way.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Paz00 can have multiple panels with different timings, but they
all share common feature - panel exposes EDID.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZiUXVA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLR5AJ9g6i7STLs6+13Oa1RF0OVucjRaHwCfUsdodreO
NWJ4C4sWE4l/KeEjbLY=
=IiTw
-----END PGP SIGNATURE-----
Merge tag 'video-20240421' of https://source.denx.de/u-boot/custodians/u-boot-video
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
Enable support for TPM2 devices. As the ATTPM20P TPM2 used on the
Gateworks Venice boards hangs off the SPI bus we enable SPI support
as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The OHCI HCD is mandatory for USB 1.1 FS/LS device support, enable it.
This used to be enabled implicitly before, now that implicit dependency
disappeared and this got disabled. Enable it manually.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/50dfa3d6-a1ca-4492-a3fc-8d8c56b40b43@kwiboo.se/
Signed-off-by: Tom Rini <trini@konsulko.com>
MCR3000 board has some components tied to the SPI bus, like the Texas
Instruments LM74 temperature sensor.
Add support for SPI bus. The SPI chipselects are a bit special in the
way that they are driven by 3 bits in a register of the board's CPLD
where the value writen in those bits exclusively activates one of the
7 possible chipselects and value 0 sets all chipselets to inactive.
So add a special GPIO driver that simulates GPIOs for those chipselect.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
