Enable support for the DWC3 USB controller and required dependencies for
Qualcomm boards, specifically the DB845c:
* IOMMU / SMMU
* USB high-speed PHYs
* Mass storage and ACM gadgets
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm FDTs are on the larger size, and with the addition of DT
modifications during board_init() it makes sense to enable OF_LIVE
globally. The cost of building the tree should be offset by the
increased efficiency at which we can walk it.
Some rough measurements with CONFIG_BOOTSTAGE suggests that this might
add 0.1-0.2ms to the boot-to-console time. However the reset-to-reset
timer difference is in the range of 0.5ms so this could just be noise.
Suffice to say, no significant slow down.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
QCS404 supports Synopsys Designware Ethernet QOS IP and we already have
the corresponding glue layer present upstream as:
drivers/net/dwc_eth_qos_qcom.c. So enable corresponding support.
Along with that it is possible for Qualcomm platforms to retrieve MAC
address from I2C eeprom present on board. So enable corresponding
support as well.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now that Turris Omnia has a rng driver provided in the MCU driver,
enable the rng command in defconfig.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for true random number generator provided by the MCU on
Turris Omnia. The MCU firmware supports TRNG if the FEAT_TRNG bit is set
in features. In that case we bind the rng driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable support for the poweroff command via sysreset for Turris Omnia.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for system power off via UCLASS_SYSRESET. Newer versions of
Turris Omnia MCU firmware can power off the board (MCU will disable
almost all voltage regulators and go into low power mode).
Move the MCU driver into drivers/misc and register it under UCLASS_MISC.
The sysreset and gpio device are bound as child devices of the MCU device.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot builds for Turris Omnia are approaching the limit of 0xf0000
bytes, which is the size of the U-Boot partition on Omnia.
Enable LTO to get more size optimized binaries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE for Kirkwood boards. And so we can directly build
DTBs from dts/upstream/src/arm/marvell, and including *-u-boot.dtsi
files from arch/arm/dts/ directory.
Background:
The following 2 commands and filters were used in the analysis to determine
which upstream DTS and DTSI files can be used as they are, or need to have
modified/created *-u-boot.dtsi for u-boot specific implementation, and
which board should be opt-out from OF_UPSTREAM.
"git grep -li arch_kirkwood configs | xargs grep DEVICE_TREE | cut -d '"' -f2 | xargs -n1 sh -c 'diff -qs arch/arm/dts/$1.dts dts/upstream/src/arm/marvell/$1.dts' sh | grep differ"
"diff -qrbu arch/arm/dts/ dts/upstream/src/arm/marvell/ | grep kirkwood | grep ".dtsi ""
More detailed information can be found at:
https://lore.kernel.org/u-boot/20240328021825.17935-1-mibodhi@gmail.com/T/#u
I've regression tested this patch with the Zyxel NSA325 (Kirkwood 88F6282)
and Zyxel NSA310S (Kirkwood 88F6281). The Zyxel NSA325 board has a
USB 3.0 controller attached to the PCIe bus. And the Zyxel NSA310S
has an extensive overhaul in bindings and styles in upstream DTS version.
Tested-by: Michael Walle <michael@walle.cc> # on lschv2
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The XEA board has following hard constraints regarding size of binaries:
- u-boot.sb < 48 KiB
- u-boot.img < 448 KiB
Added values are supposed to avoid exceeding size of binaries during
future u-boot development.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA board now has several HW revisions for SoM boards.
This patch provides support for reading this revision ID values in early
u-boot proper as production devices boot via falcon boot with correct DTB
flashed at production (so there is no need to alter SPL).
Additionally, the maximal SPL size (~55KiB) constraint is not allowing
having even simplified FIT support in it.
As a result it was necessary to handle reading GPIOs values solely in
u-boot proper as one configuration (i.e. 'single binary' -
imx28_xea_sb_defconfig) is not using SPL framework.
Moreover, the 'board_som_rev' environment variable will be used to point
correct configuration from the Linux FIT file.
Additionally, as now XEA has its second HW revision - this information is
printed when u-boot proper starts.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Set FSL_CAAM_JR_NTZ_ACCESS configuration since colibri-imx7
uses Freescale CAAM Job Ring linux driver
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
CONFIG_USB_GADGET_VENDOR_NUM is a 16-bit number, so remove
the leading zero.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reset GPIO handling is done in ETH PHY Class driver.
Enable DM_ETH_PHY.
We don't use Fixed PHY so disable PHY_FIXED.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmX8JnYcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFfPB/4g0YTnWiI0ENLumM+Q
RwcfIZJZ9YS49QPGil04i8+3TKH9b/vJZc6oyeKBQ1ZYis/kgcUHFFeMjZek8Ou5
yKd/zj861sRmRSBPD5WCSPx4YX1V6xln64vlYTvjeWs1auRuj16sPOcacxlpR6J/
p95DMt0EF5kUzCPD1WbZC6fIMhyXJT7OD1NiIJXCQT6w1hnkS2pC3Y5fiPsyR9yz
7R7yQ+hJyWBp/KsYNcgDpINSQqDSis5dd4RD/2felQ6kKGvZfuDW5pK2LyL0xAt0
Q+jNoaMw8nJQ/RxH7WbbVd0lKX0S94t/PRlCLVQkZRoWsioQ9puT38ToKTRq3yvS
2Omr
=GQJV
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2024.07 cycle:
- This feature set includes a new board named sama7g54 Curiosity.
Enable PCIe/NVMe support. Also, enable the reset, regmap and syscon
drivers which are a prerequisite for PCIe support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[SG: rebased to next branch tip]
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Enable PCIe/NVMe support. Also, enable the reset driver which
is a prerequisite for PCIe support.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Increase the SPL_STACK_R_MALLOC_SIMPLE_LEN to 0x200000 to accommodate the
size of tispl.bin fit image. With the recent upgrade of ti-linux-firmware
from version v9.1.0 to v9.2.5, the size of tispl.bin fit image has
increased to 1.4MB, causing allocation errors in the R5 SPL:
```
alloc space exhausted
Could not get FIT buffer of 1325056 bytes
check CONFIG_SPL_SYS_MALLOC_SIZE
```
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for versal-net platform as well.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240312113421.7394-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a test for the button_cmd feature. This validates that commands can
be mapped to two buttons, that the correct command runs based on which
button is pressed, that only 1 command is run, and that no command runs
if button_cmd_0_name is wrong or unset.
Additionally, fix a potential uninitialised variable use caught by these
tests, the btn variable in get_button_cmd() is assumed to be null if
button_get_by_label() fails, but it's actually used uninitialised in
that case.
CONFIG_BUTTON is now enabled automatically and was removed when running
save_defconfig.
Fixes: e761035b6423 ("boot: add support for button commands")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the necessary configs required for OSPI functionality.
Also update the ospi flash partition offsets as per the devicetree.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
This patch is to enable Agilex5 platform for Intel
product. Changes, modification and new files are
created for board, dts, configs and makefile to
create the base for Agilex5.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Move to imx8m{m,n,p}-venice to OF_UPSTREAM:
- replace the non-upstream generic imx8m{m,n,p}-venice dt with one of the
dt's from the OF_LIST
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove rudundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Move the default bootcmd from the defconfig to the board environment.
No change in functionality.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
The SARADC is used on Jaguar for multiple things:
- channel 0 is used (at runtime) as a BIOS button,
- channel 2 is exposed on the Mezzanine connector for customer specific
logic,
- channel 5 and 6 are used for identification,
Since the SARADC requires a vref-supply provided by the RK806 PMIC, its
support and the support for its regulators are also enabled.
The button, adc, pmic and regulator commands are also enabled for CLI
use in U-Boot for debugging and scripting purposes.
The RK806 PMIC on Jaguar being routed on the SPI bus, let's enable
Rockchip SPI controller driver.
Finally, the SARADC channel 1 on Jaguar is hardwired so will never
change in the lifetime of a unit, for that reason, disable the Rockchip
Download Mode check by setting ROCKCHIP_BOOT_MODE_REG symbol to 0.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Based on feedback from the mailing list while adding support for a new
device (the Powkiddy X55), correct the config options for the RGxx3
as well to remove unnecessary drivers and increase the SPL stack size.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move ROCK Pi 4 specific board code from the shared evb_rk3399 target
into its own board target and update related defconfigs to use the new
TARGET_ROCKPI4_RK3399 option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
USB gadget is not working fully as expected on RK3328, it uses a
board_usb_init() function to initialize the DWC2 OTG port.
The board_usb_init() function does not intgrate with the generic phy
framework and as a result the USB phy is not properly configured before
or after USB gadget use.
Having both USB_DWC2 and DWC2_OTG enabled for the same board is also
causing some issues.
Trying to use rockusb or ums command after usb stop result in a freeze
due to usb stop is putting the phy in a suspended state.
=> usb start
=> usb stop
=> ums 0 mmc 0
--> freeze due to usb phy is suspended <--
Fix this by only using one of USB_DWC2 (host) or DWC2_OTG (peripheral)
depending on the most likely usage of the otg port and by migrating to
use DM_USB_GADGET instead of a board_usb_init() function.
The nanopi-r2 and orangepi-r1-plus variants share OTG and power using a
Type-C connector, mark these boards dr_mode as peripheral, the most
likely usage is for recovery and image download.
The rock64 and roc-cc currently use dr_mode as host, remove the DWC2_OTG
driver from these boards to ensure that the USB_DWC2 driver is used.
The rock-pi-e board does not enable the usb20_otg node so both USB_DWC2
and DWC2_OTG is removed from this board.
Enable RockUSB and UMS on all boards with a otg port in peripheral mode.
Also with the migration to DM_USB_GADGET completed the U-Boot specific
change to reorder usb nodes in the soc device tree can be reverted.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following memory layout is typically used on RK3588:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 10M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping:
[ -X, 16M) - SPL pre-reloc stack (SPL_STACK)
[15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc
malloc heap, there is going to be an overlap when reloc malloc heap
reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to
mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Update for new boards defconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
