FTGMAC100 enables drivers/net/ftgmac100.c which uses
PHY_INTERFACE_MODE_NCSI, which is defined only when PHY_NCSI is enabled.
Therefore FTGMAC100 depends on PHY_NCSI. However adding such a
dependency causes a "recursive dependency detected!" message, so
add a dependency on NET instead (PHY_NCSI depends on NET).
All in all, either the stack is NET and FTGMAC100 can be enabled,
or it is NET_LWIP (or NO_NET) and it cannot.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PHY_NCSI enables drivers/net/phy/ncsi.c which calls net_loop() and
net_set_timeout_handler(). That's the legacy NET stack (as opposed to
NET_LWIP). Therefore add the dependency to Kconfig.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
dtsec_init_phy() is defined only with MII so add the proper conditional
in the caller code.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Generic understanding/consideration is that phy-mode as sgmi means that the
internal PCS(Physical Coding Sublayer) should be enabled by default.
Xilinx GEM implementation allows configuration GEM (gmii mode) + PL PCS PMA
(sgmii mode, Physical Medum Attachment) but in this case phy-mode should be
setup as gmii.
The reason for this assumption is that phy-mode should be described based
on GEM configuration not based on mode coming out of PHY.
Also Linux kernel automatically setting up PCSSEL bit when phy mode is
sgmii without a need to specified additional DT propety.
All our DTSes with sgmii phy mode have this flag enabled that's why there
is no need/reason to just duplicate information.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2ecdbcc4ce692e2f8b3e7054a2abab35f6c03a69.1726213052.git.michal.simek@amd.com
The AST2700 is the 7th generation SoC from Aspeed.
And use the driver to support clause 22 access.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support of Aspeed AST2700 SoC. AST2700 is based on ARM64 so modify
the DMA address related code to fit both ARM and ARM64. Besides, the
RMII/RGMII mode control register is moved from SCU500 to MAC50 so
initialize the register in ftgmac100_start correspondingly.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The TX/RX descriptor size is 16 byte.
When the cache line size is larger than 16 bytes, descriptors
flushed to RAM will flush more than one descriptor.
It is possible that it may mistakenly flush to other descriptor
that has been updated by MAC in RAM.
To avoid this issue, align the descriptors to cache line size.
Only one desc will be flushed or invalidated at a time.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The NC-SI interface does not need the MDIO bus and the
NC-SI PHY device cannot get from dm_eth_phy_connect.
Therefore, use phy_connect directly here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When executing TFTP, the ARP will be replied to after receiving
the ARP. U-boot's ARP routine modifies the data in the receive
packet in response to the ARP packet and then copies it
into the transmit packet.
At this point, the received packet cache is inconsistent.
It is possible that the cache will perform a writeback action to
affect the MAC receiving packets.
Avoid the same problem that occurs in other networking protocols.
In the free_pkt function, ensure cache and memory consistency.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
PCI devices do not necessarily use a device tree. Implement a bind()
function to assign unique device names in that case.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
PCI devices do not necessarily use a device tree. In that case, the
driver currently fails to find eqos->config and eqos->regs.
This commit factors out the respective functionality. Device tree usage
remains default, but board specific implementations will be possible as
well.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Before this commit, usage of this header relied on a specific include
order. Fix it by including all dependencies.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Bevor this commit, only clause 22 access was possible. After this commit,
clause 45 direct access will available as well.
Note that there is a slight change of behavior: Before this commit, the
C45E bit was set to whatever value was left in the register from the
previous access. After this commit, we adopt the common practice of
discerning C45 from C22 using the devad argument.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
* Qualcomm platforms >~2016 gain support for the RPMh (Resource Power Manager)
peripheral which is used to control most regulators. The RB5 is now able to
power up its USB VBUS regulator via the rpmh regulator driver. Git history
from the original Linux driver is preserved for ease of maintenance.
* IPQ40xx SoCs gain ethernet networking support via the new ESS EDMA driver.
This adds the driver for the ESS EDMA ethernet adapter
found inside of Qualcomm IPQ40xx SoC series.
This driver also integrates the built in modified QCA8337N
switch support as they are tightly integrated.
Co-Developed-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add the compatible string for the emac found on the V3s SoC. The SoC
only supports the internal PHY. There are no (R)MII signals on any pins.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Christian Marangi <ansuelsmth@gmail.com> says:
This is an initial series that have all the initial trivial
fixes required for usage of OF_UPSTREAM for the mediatek SoC
This also contains the pcie-gen3 driver and the required tphy
support driver to make it work.
Subsequent series will follow with conversion of the mtk-clk
to permit usage of OF_UPSTREAM and upstream clk ID.
MT7981, MT7986 and MT7988 migration to upstream clock ID
is complete and working on MT7623.
Series CI tested with PR: https://github.com/u-boot/u-boot/pull/590
This patch adds support for Intel Foxville I226
devices LM,V,I,K in e1000 driver.
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
The implementation of icache_invalid appears to be doing what other
architectures call invalidate_icache_all so rename to match.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for a property 'phy-reset-gpios' to reset PHY
chipset.
Signed-off-by: Heesub Shin <heesub@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When bcmgenet complete to write Rx buffer with the DMA,
some U-Boot commands write data to the buffer directly.
Those write data will become dirty in CPU cache.
After this driver calls free_pkt to the buffer,
the buffer is assigned as the future Rx buffer.
At some point, if bcmgenet writes to a buffer with DMA
and CPU cache flushes dirty data to the buffer,
the buffer is corrupted.
This patch calls flush_dcache_range in free_pkt
to immediately flush the data written by U-Boot command
and prevent data corruption.
This issue can be reproduced using wget on Raspberry Pi4.
If wget receives data larger than
RX_BUF_LENGTH * RX_DESCS = 2048 * 256 bytes,
it will timeout due to data corruption.
In addition, if LOG_DEBUG is enabled in net/tcp.c,
the following error log is output.
TCP RX TCP xSum Error
Signed-off-by: Yasuharu Shibata <yasuharu.shibata@gmail.com>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Let users configure default auto-negotiation timeout via Kconfig
instead of specifying it in board configuration headers. This is
the first step toward converting this to Kconfig fully, so far the
legacy PHY_ANEG_TIMEOUT in configuration headers takes precedence.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
The eth-uclass state machine doesn't prevent imbalanced start()/stop()
calls - to the contrary, it even provides eth_init_state_only() and
eth_halt_state_only() functions that change the state without any calls
into the driver. This means that the driver must be robust against
duplicate start() and stop() calls as well as send/recv calls while the
interface is down.
We decide not to print error messages but just to return an error in the
latter case, as trying to send packets on a disabled interface commonly
happens when the netconsole is still active after the Ethernet has been
halted during bootm.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This driver support the Synopsys Designware Ethernet 10G
IP block refer from the driver dwc_eth_qos.
The driver MAC register mapping is different between
Synopsys QoS IP and Synopsys 10G IP, and thus new file
is created meant for Sysnopsys 10G IP.
The dwc_eth_xgmac_socfpga.c is specific to a device family,
the driver support the specific configuration used in
Intel SoC FPGA Agilex5.
This driver is extensible for other device family to use.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Initialize register in cv1800b ethernet phy to make it compatible with
generic phy driver
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move cru_rk3308.h and grf_rk3308.h to arch-rockchip to match path used
for all other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync device tree from linux v6.8 and rename the rockchip,rk3308-mac
compatible in gmac_rockchip driver to match upstream linux.
Also move rk3308-roc-cc gmac node to u-boot.dtsi to not break features
not enabled in upstream device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmYiQ/EcHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/ph+3D/4qsN+tYQYzBfCnhCjA
eEHMHGS6wBUg4riF5bjvk68CEVDIxm7NARFJi0RodvYsOZF7kLLyELm9yyNcWb+1
gkqLNcLLWFRhLyAIfCTnl88+luR6F48TPdVIXw17Vb3n4Fc99ICaS2PHYbHeRbR+
d/oga0DBz2N21+scYrUjPQoeczdk/fui84AXF7u8/7zFdYY0p50wHItKQHt4KXMv
TnM9KbeHGlxRdIiVR2Jvv5Q51mhwv8XczgOZdmGLDYBV3xKexacHsLgfVcwSM2C8
1YHFA6VWVAOcJyQ+VFKmQw0JoTUWueJCY21T6H6fsAnpMTc9tksu3nLJO0P8CCN0
IbI50trzLWPy/BZtqJwV67durp6ZA6hT5wQOTo7NHAFocql9hJKtDuhvTVHqmx6R
6SWpTWD24Mkgd9FrXk/yMEUOmihOB8U6q+GkyPf/yfWyZK93mUwiRStFkBwEz8QY
AX5gNoQ7+zJhkfZ4VdsCsFaVJV7Y9vlN3hnNhqLVEhXJ9GvFOszAZOTuuO8rLAv7
i7HE8Hk7zv6j15qSUPKOQv8BO0eVFlLPzTXS9F/uzSlpjfpNIs7At3TyQ4pAukRo
uHc7KjHpVAkC+7YeMuVR3VFQ/p2+5EyxMclKIvGlOxqD/+m1Keu+C4/gTkWYlIgx
mWqsvZCAi2RmDcUWBBB2mHpswQ==
=up9Y
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20240419' of https://source.denx.de/u-boot/custodians/u-boot-stm
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Use const bool for the values parsed out of DT. Drop the duplicate
assignment of false into those bool variables, assign them directly
with the content parsed out of DT. Abbreviate the variable name too.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use dev_*() only to print all the logs from this glue code,
instead of mixing dev_*(), log_*(), pr_*() all in one code.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the log_debug() calls on top of the bit manipulation code.
No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use FIELD_PREP to configure content of ETH_SEL bitfield in SYSCFG_PMCSETR
register. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Replace ifdef CONFIG_CLK with if (CONFIG_IS_ENABLED(CLK)) to improve code
build coverage. Some of the functions printed debug("%s: OK\n", __func__);
on exit with and without CLK enabled, some did not, make it consistent and
print nothing if CLK is disabled.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move board_interface_eth_init() into eqos_probe_syscfg_stm32() in STM32
driver glue code. The eqos_probe_syscfg_stm32() parses STM32 specific DT
properties of this MAC and configures SYSCFG registers accordingly, there
is nothing board specific happening in this function, move it into generic
driver code instead. Drop the now unused duplicates from board files.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The current glue code is specific to STM32MP15xx, the upcoming STM32MP13xx
will introduce another entry specific to the STM32MP13xx. Rename the current
entry to eqos_stm32mp15_config in preparation for STM32MP13xx addition. No
functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move STM32 glue code into separate file to contain the STM32 specific
code outside of the DWMAC core code. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER<christophe.roullier@foss.st.com>
Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
