No functional change. Group devm_reset_control_get() and
devm_reset_control_get_optional() to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Group all devm_clk_get_optional() to a
separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Cadence Sierra PHY driver registers PHY using devm_phy_create()
for all sub-nodes of Sierra device tree node. However Sierra device
tree node can have sub-nodes for the various clocks in addtion to the
PHY. Use devm_phy_create() only for nodes with name "phy" (or "link"
for old device tree) which represent the actual PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Commit 39b823381d9d ("phy: cadence: Add driver for Sierra PHY")
de-asserts PHY_RESET even before the configurations are loaded in
phy_init(). However PHY_RESET should be de-asserted only after
all the configurations has been initialized, instead of de-asserting
in probe. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The driver enables IPU support. Basically enables the clocks,
timers, watchdog timers and bare minimal MMU and supports
loading the firmware from mmc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix compile warnings]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add remoteproc resource handling helpers. These functions
are primarily to parse the resource table and to handle
different types of resources. Carveout, devmem, trace &
vring resources are handled.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix redefinition of "struct resource_table" and compile warnings ]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add a reset driver to bring IPs out of reset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: reset_ops structure member "free" has been renamed to "rfree",
use the latter instead]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
There is a 4 bit VARIANT number inside the JTAGID register that TI
increments any time a new variant for a chip is produced. Each
family of TI's SoCs uses a different versioning scheme based off
that VARIANT number.
CC: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
In Multi DDR subystems with interleaving support, the following needs to
configured,
- interleaving granular size and region
- EMIFs to be enabled
- EMIFs with ecc to be enabled
- EMIF separated or interleaved
- number of cycles of unsuccessful EMIF arbitration to wait before
arbitrating for a different EMIF port, by default set to 3
Add support for configuring all the above by using a MSMC device
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The current driver only supports single instance of DRR subsystem. Add
support for probing multiple instances of DDR subsystem.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add a pointer to ddr instance int the lpddr4_privatedata_s structure for
supporting mutliple instances of DDR in the drivers.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The clock composite is required when using the clock framework. So
select it automatically.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When regulator consumer attempts to set enabled DVS regulator voltage,
the driver aborts with "Only DVS bucks can be changed when enabled".
In case the regulator is already set to specified voltage, do nothing
instead of failing outright.
When regulator consumer attempts to set enables regulator which cannot
be controlled because it is already always enabled, the driver aborts
with -EINVAL. Again, do nothing in such case and return 0, because the
request is really fulfilled, the regulator is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Initial support for Fairchild's 8 bit I2C gpio expander FXL6408.
The CONFIG_FXL6408_GPIO define enables support for such devices.
Based on: https://patchwork.kernel.org/patch/9148419/
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
After acking the requested frequency, should wait the ack bit clear
by DDR controller and check the DFS interrupt for next request polling.
Otherwise, the next polling of request bit will get previous value
that DDR controller have not cleared it, so a wrong request frequency
is used.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8ULP, The dram config timing need to be saved into sram for
ddr retention when APD enter PD mode, so add this support on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Spi memory operation interface is added to zynq qspi
driver to provide an high-level interface to execute
qspi controller specific memory operations by avoiding
spi_mem_exec_op() from spi-mem framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a check afer baudrate calculation to see if the resultant value
falls within the range, else set it to default baudrate value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read only one byte at a time from txbuf as txbuf may not be
aligned and accessing more than a byte at a time may cause
alignment issues. This fixes the issue of data abort exception
while writing to flash device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-3-ashok.reddy.soma@xilinx.com
This patch typecasts and accesses rx buf properly as
an unaligned rxbuf, typecasting with u16 and accessing
it causes data abort exception and this patch fixes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-2-ashok.reddy.soma@xilinx.com
In case fastboot over Ethernet, am65_cpsw_stop() is not called unless
DM_FLAG_OS_PREPARE is set. Without call to am65_cpsw_stop(), DMA
resources are not released thus leading to failures in kernel.
Fix this by adding DM_FLAG_OS_PREPARE flag to am65_cpsw_nuss_port
driver.
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If we just use fdtdec_get_addr_size_fixed to get "reg" it will use
64bit address cell to get the base address.
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible ="SiFive,FU500-soc", "fu500-soc", "sifive-soc", "simple-bus";
ranges;
L28: axidma@30010000 {
#dma-cells = <1>;
compatible = "xlnx,axi-dma-1.00.a";
axistream-connected = <&L27>;
axistream-control-connected = <&L27>;
clocks = <&L1>;
interrupt-parent = <&L6>;
interrupts = <32 33>;
reg = <0x30010000 0x4000>;
fdtdec_get_addr_size_fixed: reg: addr=3001000000004000
We should get the base address through its parent's address-cells and
size-cells settings. So we should use fdtdec_get_addr_size_auto_parent()
to get correct base address.
After applying this patch, we can get the correct base address of dma by
replacing fdtdec_get_addr_size_fixed() with
fdtdec_get_addr_size_auto_parent().
fdtdec_get_addr_size_auto_parent:
na=1, ns=1, fdtdec_get_addr_size_fixed: reg: addr=30010000
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20220120084128.1892101-1-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Populate mtd->dev with flash_info->dev which allows to get
full mtd information using the "mtd list" command.
Before, "mtd list" command returns :
List of MTD devices:
* nor0
- type: NOR flash
- block size: 0x40000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "nor0"
After this patch we get for example:
List of MTD devices:
* nor0
- device: flash@0
- parent: spi@40430000
- driver: cfi_flash
- path: /soc/spi@40430000/flash@0
- type: NOR flash
- block size: 0x40000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "nor0"
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that all in-tree boards have been converted to the compatible
strings from Linux, delete the support for the ad-hoc "pcf2127-rtc" one.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow this driver to be used by boards which inherit their device trees
from Linux. Compatibility is temporarily retained with the old
compatible string which is U-Boot specific, and will be removed after a
few changes.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This seems to be very similar to the already existing PCA9547, save for
the fact that it supports 0.8V and doesn't support 5V. In fact, it is so
similar to the PCA9547 that the NXP LS1028A-RDB board has been driving
this chip using a "nxp,pca9547" compatible string.
Create a new compatible for the PCA9847 (which is the same as in Linux)
and define the same operating parameters for it as for PCA9547.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The current fixup of LX2160A PCIe nodes is based on non-production
rev1 silicon, and in Linux the nodes have been updated for rev2
silicon, so update the searching compatible string to match the
kernel changes. And for compatibility with the rev1 nodes, move
forward the board specific fixup.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, pin configuration does not need a platform-specific function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This, along with gpio_flags_xlate(), allows the GPIO driver to handle
pull-up/down flags provided by consumer drivers or in the device tree.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This adds a compatible string for the Allwinner Sun4i-A10 I2C
controller. Without this, boards based on the R8 and A13 (at a
minimum) fail to boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Akash Gajjar <gajjar04akash@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The driver for SPI0 on Allwinner H6 SoCs did not use the correct define
SUN50I_GPC_SPI0 for the pin function, but one for a different Allwinner
SoC series.
Fix the conditionals to use the correct define for H6 SoCs. This matches
the conditional logic in the SPL spi driver.
Tested by probing the spi-flash on a pine64_h64-model-b board with
adapted device-tree (disable mmc2, enable spi0).
Signed-off-by: Daniel Wagenknecht <dwagenk@mailbox.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For printing phys_addr_t we should use %pa to avoid warning like:
drivers/bootcount/bootcount_syscon.c:110:17: note: in expansion of macro ‘dev_err’
110 | dev_err(dev, "%s: Unsupported register size: %d\n", __func__,
| ^~~~~~~
seen for sandbox_defconfig with CONFIG_PHYS_64BIT=y.
Cf. commit 1eebd14b7902 ("vsprintf: Add modifier for phys_addr_t")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the DFU MTD backend for the UBI partitions with the mtd command write
behavior when the option .dontskipff is not used: don't write the empty
pages (full of 0xFF); it is not required for UBI, see [1] for details.
This patch avoids the "free space fixup" procedure in the kernel [2]
and allows to program a UBIFS volume generated by mkfs.ubifs without the
option -F, --space-fixup.
The MTD DFU backend implements this behavior introduced on DFU NAND
backend by the commit 13cb7cc9e8e4 ("dfu: Add option to skip empty pages
when flashing UBI images to NAND") and also supported by the command nand
by CONFIG_CMD_NAND_TRIMFFS and by commit c9494866df83 ("cmd_nand: add nand
write.trimffs command").
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
[2] http://www.linux-mtd.infradead.org/faq/ubifs.html#L_free_space_fixup
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Initially it is set to dev_seq but update to the last bus number is
missing. Fix it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Having U-Boot look up the passed partition name even though an alias
exists is unexpected, leading to warning messages (when the alias name
doesn't exist as a real partition name) or the use of the wrong
partition.
Change part_get_info_by_name_or_alias() to consider real partitions
names only if no alias of the same name exists, allowing to use aliases
to override the configuration for existing partition names.
Also change one use of strcpy() to strlcpy().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
In DFU v1.1 specification [1] the DFU_UPLOAD (Short Frame)
is handled only in dfuUPLOADIDLE state:
- Figure A.1 Interface state transition diagram
- the state description in chapter A.2
A.2.3 State 2 dfuIDLE
on Receipt of the DFU_UPLOAD request,and bitCanUpload = 1
the Next State is dfuUPLOADIDLE
A.2.10 State 9 dfuUPLOAD-IDLE
When the length of the data transferred by the device in response
to a DFU_UPLOAD request is less than wLength. (Short frame)
the Next State is dfuIDLE
In current code, when an UPLOAD is completely performed after the first
request (for example with wLength=200 and data read = 9), the DFU state
stay at dfuUPLOADIDLE until receiving a DFU_UPLOAD or a DFU_ABORT request
even it is unnecessary as the previous DFU_UPLOAD request already reached
the EOF.
This patch proposes to finish the DFU uploading (don't go to dfuUPLOADIDLE)
and completes the control-read operation (go to DFU_STATE_dfuIDLE) when
the first UPLOAD response has a short frame as an end of file (EOF)
indicator even if it is not explicitly allowed in the DFU specification
but this seems logical.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case CONFIG_FASTBOOT_FLASH_MMC_DEV == 0, compile-time condition
is not met and fastboot_set_reboot_flag() fails.
Fixes: a362ce214f03 ("fastboot: Implement generic fastboot_set_reboot_flag")
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
