Obtain USB phy configuration from phy node if such exists
and is enabled. If no, set default values.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
In some cases access to GPIOs is needed so early that DM
is not ready even nearly. These functions are exactly for
this case.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra 3 has UART-E exposable via SD card slot which may be
handy for debugging. This change only adds funcmux part, to
use UART-E on the device you additionally would need:
- set stdout-path to serial@70006400 (uarte)
- configure sdmmc1_dat3_py4 and sdmmc1_dat2_py5 pinmux for
uarte
- disable or remove sdhci@7800000 node
- enable CONFIG_TEGRA_ENABLE_UARTE in defconfig
- set CFG_SYS_NS16550_COM to NV_PA_APB_UARTE_BASE in device
header
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
i.MX8MP SDHC use CLK_IMX8MP_DUMMY clk entry. Without the clk, the bulk
api will return failure.
The correct entry should be replaced with IMX8MP_IPG_ROOT clk in device
tree. This will be done in Kernel device tree and sync to U-Boot in
future:
https://lore.kernel.org/all/20241012025221.1728438-1-peng.fan@oss.nxp.com/
Fixes: 76332fae769 ("mmc: fsl_esdhc_imx: Enable AHB/IPG clk with clk bulk API")
Reported-by: Gilles Talis <gilles.talis@nxp.com>
Tested-by: Gilles TALIS <gilles.talis@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When OSCCA is enabled, FSB fuse shadow (offset 0x8000)
access is disabled for SOC. So update the driver to read fuse
from ELE API. The ELE has supported to read all shadow fuses like
FSB, reuse the table of FSB for the word index used by ELE API.
Add ELE shadow fuse read and write to current ELE fuse driver.
But when LC is OEM closed, the ELE read/write shadow fuse APIs are
forbidden. Reading from any fuse will return error. This causes
problem to u-boot which must read out some fuse no matter whatever LC.
So we have to change back to read from FSB and ELE common fuse read API.
For using ELE shadow read API for development purpose like checking
the ELE shadow fuse write result, user can set env variable
"enable_ele_shd" to y to switch it.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is a bug when checking fuse word with redundancy fuse in FSB
table. The redundancy fuses are combined into 4 words, so we can't
directly use word index to do the check, otherwise the high 4 words
will fail to match.
And When calling ELE API, res parameter will pass to ELE API to get ELE
response value for failure. So most of usage does not initialize
this variable and print it after calling ELE API.
However, when ELE API returns failure, we can't ensure this res is
always set because there may be other failure like MU failure.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add ELE APIs to support read and write shadow fuses
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8ULP, the word index 1 is used to read OTP_UNIQ_ID with 4 words
data responsed. However this special index does not apply others.
So restrict the check to i.MX8ULP to avoid problem when reading from
fuse word 1 for others, such as i.MX93.
Also update header order
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When OS is doing ELE API call, before OS get the response, OS is force
reseted, then it is possible that MU RR has data during initialization
in SPL stage. So clear the RR registers, otherwise SPL ELE API call will
work abnormal.
Cc: Alice Guo <alice.guo@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MU parameter register can provide the TR and RR number.
For i.MX95 which has 8 RR is different with i.MX93 and i.MX8ULP,
so update the driver to read the PAR for exact TR and RR number.
Also update compatible string for i.MX95 ELE MU.
Cc: Alice Guo <alice.guo@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
The Broadcom BCA platforms are broadband access SoCs.
This is a port of the upstream Linux driver to U-Boot.
It was based on drivers/mtd/nand/raw/brcmnand/bcmbca_nand.c
from Linux v6.11.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When ECC parameters are not specified in DT, first try ONFI ECC parameters
before fallback to maximum strength.
It's the Linux driver behavior since the driver rewriting in f88fc12.
From then 2 nand system refactors have been done in 6a1b66d6 and 53576c7b,
chip->ecc_strength_ds and chip->ecc_step_ds became
nanddev_get_ecc_requirements(). U-Boot didn't follow the refactor and
always use these 2 fields.
v2: Fix formatting, add upstream commit hash.
Signed-off-by: Zixun LI <zli@ogga.fr>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Balamanikandan Gunasundar
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
SPL_BUILD is not a Kconfig symbol. Perhaps the intent here is to use
SPL instead. However, this causes build errors, e.g. with T1024RDB_NAND
So drop the dependency on !SPL_BUILD since it does nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function cdns3_ep_config() calculates the maximum packet size based
on the Endpoint Type and the Gadget Speed and stores it in the variable
"max_packet_size". This value is then programmed in the USB Controller
for the corresponding Endpoint. This may result in a mismatch between
the maximum packet size programmed in the USB controller and the maximum
packet size seen by the UDC Core via "maxpacket" member of "struct usb_ep".
Additionally, since TD_SIZE is calculated in cdns3_ep_run_transfer() on the
basis of the maximum packet size stored in the "maxpacket" member of
"struct usb_ep", it may lead to an incorrect value of TD_SIZE when compared
with what the USB controller actually expects (max_packet_size).
Fix this.
Fixes: 7e91f6ccdc84 ("usb: Add Cadence USB3 host and gadget driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20241007121927.1680039-1-s-vadapalli@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
When DM_REGULATOR is disabled, all calls will return -ENOSYS. Account
for that so that targets like the IOT2050 will work again.
Fixes: de451d5d5b6f ("usb: dwc3-generic: support external vbus regulator")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Christian Marangi <ansuelsmth@gmail.com> says:
This series is a reworked version of the previous seried:
misc: introduce STATUS LED activity function
This series port and expand the legacy concept of LED boot from
the legacy Status LED API to new LED API.
One thing that many device need is a way to communicate to the
user that the device is actually doing something.
This is especially useful for recovery steps where an
user (for example) insert an USB drive, keep a button pressed
and the device autorecover.
There is currently no way to signal the user externally that
the bootloader is processing/recoverying aside from setting
a LED on.
A solid LED on is not enough and won't actually signal any
kind of progress.
Solution is the good old blinking LED but uboot doesn't
suggest (and support) interrupts and almost all the LED
are usually GPIO LED that doesn't support HW blink.
Additional Kconfg are also introduced to set the LED boot and
activity. Those are referenced by label.
A documentation for old and these new LED API is created.
Implement LED activity API similar to BOOT LED API.
Usual activity might be a file transfer with TFTP, a flash write...
User of this API will call led_activity_on/off/blink() to signal these
kind of activity.
New Kconfig is implemented similar to BOOT LED, LED_ACTIVITY to
enable support for it.
It's introduced a new /options/u-boot property "activity-led" and
"activity-led-period" to define the activity LED label and the
default period when the activity LED is set to blink mode.
If "activity-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement LED boot API to signal correct boot of the system.
led_boot_on/off/blink() are introduced to turn ON, OFF and BLINK the
designated boot LED.
New Kconfig is introduced, CONFIG_LED_BOOT to enable the feature.
This makes use of the /options/u-boot property "boot-led" to the
define the boot LED.
It's also introduced a new /options/u-boot property "boot-led-period"
to define the default period when the LED is set to blink mode.
If "boot-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
To cache the data we repurpose the now unused led_uc_priv for storage of
global LED uclass info.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ofnode_options helpers to read options in /options/u-boot to
adapt to the new way to declare options as described in [1].
[1] dtschema/schemas/options/u-boot.yaml
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We currently init the LED OFF when SW blink is triggered when
on_state_change() is called. This can be problematic for very short
period as the ON/OFF blink might never trigger.
Toggle the LED (ON if OFF, OFF if ON) on initial SW blink to handle this
corner case and better display a LED blink from the user.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add newline character in log info end.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add PCA9452 PMIC/Regulator support.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The pmic could be trimed with updated BUCK1 range, so update the range
for trimed pmic. The default value of Toff_Deb is used to distinguish
the non-trimed and trimed pmic.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S28HS02GT is dual-die package parts and do not support chip erase.
Fixes: 16dd1095101 ("mtd: spi-nor-ids: Add Infineon(Cypress) s28hs02gt ID")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
S25HL02GT and S25HS02GT are dual-die package parts and do not support
chip erase.
Fixes: c95a914aed7 ("mtd: spi-nor-ids: Add Cypress s25hl-t/s25hs-t")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
The S25FS064S, S25FS128S, and S25FS256S are the same family of SPI NOR
Flash devices with S25FS512S. Some difference depending on the device
densities are taken care in post SFDP fixup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
The 6th ID byte is needed to distiguish S25FL-S and S25FS-S families.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The correct 4KB erase opcode should be selected based on the address width
currently used.
Fixes: 562d166a13 ("mtd: spi-nor-core: Add fixups for s25fs512s")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The mx25u25635f entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: f0084f1dfdbc ("drivers/mtd/spi/spi-nor-ids.c: add mx25u25635f support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The w25q16dw entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: baef13ec9d59 ("mtd: spi-nor-ids: Add support for flashes tested by xilinx")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Some Winbond SPI NORs have special SR3 register which is
used among other things to control whether non-standard
"Individual Block/Sector Write Protection" (WPS bit)
locking scheme is activated. This non-standard locking
scheme is not supported by either U-Boot or Linux SPI
NOR stack so make sure it is disabled, otherwise the
SPI NOR may appear locked for no obvious reason.
This SR3 WPS appears e.g. on W25Q16FW which has the same ID as
W25Q16DW, but the W25Q16DW does not implement the SR3 WPS bit.
Signed-off-by: Marek Vasut <marex@denx.de>
When trying to set the DCDC4 regulator, the code was accidentally
setting the voltage register for DCDC5 (VCC-DRAM). The higher voltage
doesn't harm the DRAM chips, but upsets the Linux regulator driver: when
it tried to correct that, it tripped over a separate DT bug.
The DCDC5 DT limits are 1.425 and 1.575V, which cannot bet set with the
rail's resolution of 50mV. The kernel driver gave up, and made in turn
the system hang, as the PMIC powers essential devices.
Fix the copy&paste bug by using the correct PMIC voltage register.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Clock gates and reset lines share a common structure in the sunxi clock
driver descriptions, but use different flags to tell them apart.
The description of the Allwinner A80 MMC clock reset lines was
erroneously using the "GATE" macro, which made the reset driver ignore
that entry, complaining with:
sunxi_set_reset: (RST-reset:#0) unhandled
Change that to the correct "RESET" macro, to make the reset driver
happy.
Fixes e0c7ce7e52b7 ("sunxi: clk: A80: add MMC clock support")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
John Watts <contact@jookia.org> says:
I'm doing some SPI work so I tried to compile all the drivers on my
sunxi board to try and avoid some regressions. This failed, so here are
some fixes for this.
Link: https://lore.kernel.org/r/20240427-spikconfig-v1-0-8a54772522f4@jookia.org
Signed-off-by: Tom Rini <trini@konsulko.com>
These dependencies are required for building the drivers and create
compile errors if not enabled.
Signed-off-by: John Watts <contact@jookia.org>
[trini: Add ARCH_MVEBU to KIRKWOOD_SPI]
Signed-off-by: Tom Rini <trini@konsulko.com>
