tsel contrl clock drives are required to configure PHY
929, 939 controls drive settings.
Add support for these control clock for all dramtype
sdrams.
Thse control clock drives are configure via tsel_ckcs_select_p
and tsel_ckcs_select_n variables.
tsel_ckcs_select_n is PHY_DRV_ODT_34_3 value where as
tsel_ckcs_select_p is retrived from IO settings for lpddr4
and rest uses PHY_DRV_ODT_34_3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Now we have IO settings available for all supported sdram
frequencies, so retrieve these IO settings and make used
for LPDDR4 ds odt configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Add IO settings for dram ctl and phy.
IO settings are useful for configuring ctl, phy odt, vref,
mr5, mode select and other needed input output operations
for lpddr4 or any other dramtype sdram.
Right now, this patch added IO setting for all supported
sdram frequencies.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
The hardware for LPDDR4 with
- CLK0P/N connect to lower 16-bits
- CLK1P/N connect to higher 16-bits
and usually dfi dram clk is configured via CLK1P/N, so
disabling dfi dram clk will disable the CLK1P/N as well.
So, add patch to not to disable dfi dram clk for lpddr4,
with rank 1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
tsel write ca_p and ca_n values need to write on PHY 544, 672
and 800 to configure ds odt.
Configure the same PHY register for lpddr4 would require a mask
value of (300 << 8).
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Assign desired cs_map values for lpddr4 during set memory map.
Initial cs_map values is based on the sdram parameters, so
the same will adjusted based dramtype as LPDDR4.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
PHY_898, PHY_919 would require to configure PHY LP4 boot
pll control and ca for lpddr4.
So, configure the same in pctl_cfg for LPDDR4.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
It is possible in lpddr4 dram, where both the channels would
start at same time with ZQ Cal Start. If it uses ZQ Call start
then it will use RZQ.
For example LPDDR4 366 Dual-Die, Quad-Channel Package, RZQ maybe
connect to both channel. If ZQ Cal Start at the same time,
it will use the same RZQ.
It is not a problem of using RZQ in both the channels, but can not
use at the same time.
So, to avoid this, we have an option of dram tINIT3 value for
increasing the frequency for channel 1.
This patch increase the available tINIT3 with existing running
dram frequency.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
lpddr4 has PLL bypass mode during phy initialization phase,
which does all pll configurations.
So no need to wait explicitly during pctl config.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
mode_sel assignment is based on dram type.
In phy_io_config, already have vref setting based
on the dram type, so move this mode_sel assignment
on vref setting area.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number for lpddr4.
This would keep the wdql data training loop based on the
desired rank mask value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number for lpddr4.
This would keep the ca data training loop based on the
desired rank mask value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Supporting LPDDR4 code support in RK3399 would increases
the size of SPL/TPL.
So add kconfig entry for RK3399 LPDDR4 code so-that
the boards have LPDDR4 can enable them via defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Some dramtypes like lpddr4 initialization would required to
configure phy IO even after pctl_cfg and after set_ds_odt.
For those cases the set_ds_odt would be an initial call to
setup the phy.
To satisfy all the cases, trigger phy IO from set_ds_odt.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrMode structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrTimingC0 structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add dram config macro for handling ddr version number.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Use dram config variable name as sys_reg2 instead of sys_reg
since the final variable value is to written into a pmugrf
register named as sys_reg2.
This reflect the both variable and associated register
names are same and also help to add next sys_reg's to
add it in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add simplified and meaningful macro for all setting.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
This would help to debug the sdram base parameters while
debugging existing chip or while supporting new sdram type.
It require explicit enablement of CONFIG_RAM_ROCKCHIP_DEBUG
for showing the debug prints.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Right now the rk3399 sdram driver assume that the board
has configured with 2 channels, so any possibility to
enable single channel on the same driver will encounter
channel #1 data training failure.
Log:
U-Boot TPL board init
sdram_init: data training failed
rk3399_dmc_init DRAM init failed -5
So, add an algorithm that can capable to compute the active
or configured rank with associated channel like
a) do rank loop to compute the active rank, with associated
channel numbers
b) then, succeed the data training only for configured channel
c) preserve the rank for given channel
d) do channel loop for setting the active channel
e) if given rank is zero or inactive on the specific channel,
clear the timings for the associated channel
f) finally, return error if number of channels is zero
Tested in NanoPI-NEO4 since it support single channel sdram
configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(add PI_READ_GATE_TRAINING for LPDDR3 to support rk3399-evb case)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
This patch fixes not enabled uart2 (and hence serial console) on i.MX53
devices. After following commit 1d255904c306 ("ARM: dts: imx: imx53:
Synchronize iMX53 DT with Linux") from the uart2 compatible the
'fsl,imx7d-uart' has been removed (which was correct).
However, the root cause of the problem was the commit 98d62e618bb9 ("arm:
imx: add i.MX53 Beckhoff CX9020 Embedded PC") which introduced this
compatible.
Moreover, without this patch all i.MX53 UARTs are not usable as neither
'fsl,imx53-uart' nor 'fsl,imx21-uart' are in compatible IDs in
drivers/serial/serial_mxc.c file.
The fix is to add 'fsl,imx53-uart' and 'fsl,imx21-uart' as compatibles
for the aforementioned serial driver (those are also defined in the Linux
kernel).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The DM_FLAG_PRE_RELOC shall be set unconditionally as this driver is going
to be re-used in both early SPL and U-Boot proper's pre-reloc.
For i.MX based devices it is crucial to have available the serial console
before relocation (otherwise the board may hand).
The device definition may be provided either via device tree description or
with U_BOOT_DEVICE(mxc_serial) definition. In the latter case the device
will not bind in U-Boot proper when DM_FLAG_PRE_RELOC is not set.
The !CONFIG_IS_ENABLED(OF_CONTROL) #if check was set as a "workaround" for
DM problem described in following commit 4687919684e0
("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers").
Let's look on this check more thoroughly - we add this flag if the board
doesn't support OF_CONTROL. This is a bit strange as the serial_mxc.c can
be used with CONFIG_DM_SERIAL but without corresponding device tree
description (OF_CONTROL). In such case the aforementioned
U_BOOT_DEVICE(mxc_serial) definition is used.
Other boards/SoCs have this flag set unconditionally for serial driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add DM and DT probing support to iMX watchdog driver. This should
allow boards to move over to this driver, enable SYSRESET_WATCHDOG
to handle cpu_reset() if required.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code responsible for setting proper values in the MUX registers
(in the mxs_pinctrl_set_state()) has been ported from Linux kernel
- SHA1: 17bb763e7eaf tag v5.1.11 from linux-stable.
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes,
it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also
make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds support for DM/DTS in the mxs_gpio.c driver.
Information regarding per gpio controller pin number is passed via DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled.
One only needs to add proper compatible and dependency on FEC_MXC in the
Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
This patch provides code to implement the CCF clock tree in sandbox. It
uses all the introduced primitives; some generic ones are reused, some
sandbox specific were developed.
In that way (after introducing the real CCF tree in sandbox) the recently
added to clk-uclass.c: clk_get_by_id() and clk_get_parent_rate() are tested
in their natural work environment.
Usage (sandbox_defconfig and sandbox_flattree_defconfig):
./u-boot --fdt arch/sandbox/dts/test.dtb --command "ut dm clk_ccf"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic mux clock code for CCF requires reading the clock multiplexer
value from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the mux structure (accessible only when sandbox is run)
has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic divider clock code for CCF requires reading the divider value
from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the divider structure (accessible only when sandbox is
run) has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If the CLK_GET_RATE_NOCACHE flag is set - the clk_get_parent_rate()
provides recalculated clock value without considering the cache setting.
This may be necessary for some clocks tightly coupled with power domains
(i.e. imx8), and prevents from reading invalid cached values.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch brings the files from Linux kernel (linux-stable/linux-5.1.y
SHA1: 5752b50477da)to provide clocks support as it is used on the Linux
kernel with Common Clock Framework [CCF] setup.
The directory structure has been preserved. The ported code only supports
reading information from PLL, MUX, Divider, etc and enabling/disabling
the clocks USDHCx/ECSPIx depending on used bus. Moreover, it is agnostic
to the alias numbering as the information about the clock is read from the
device tree.
One needs to pay attention to the comments indicating necessary for U-Boot's
driver model changes.
If needed, the code can be extended to support the "set" part of the clock
management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds the clk_get_by_id() function, which is responsible
for getting the udevice with matching clk->id. Such approach allows
re-usage of inherit DM list relationship for the same class (UCLASS_CLK).
As a result - we don't need any other external list - it is just enough
to look for UCLASS_CLK related udevices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent_rate() function, which is responsible
for getting the rate of parent clock.
Unfortunately, u-boot's DM support for getting parent is different
(the parent relationship is in udevice) than the one in Common Clock
Framework [CCF] in Linux.
To alleviate this problem - the clk_get_parent_rate() function has been
introduced to clk-uclass.c.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent() function, which is responsible
for getting the parent's struct clock pointer.
U-Boot's DM support for getting parent is different (the parent
relationship is in udevice) than the one in Common Clock Framework [CCF]
in Linux. To obtain the pointer to struct clk of parent the
pdev->uclass_priv field is read via dev_get_clk_ptr() wrapper.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Up till now the fixed rate clock ('osc') has been added to UCLASS_CLK
without declaring struct clk. As a result it was only accessible by
iterating the udevice's uclass list.
This is a problem for clock code, which operates on pointers to struct
clk (like clk_get_rate()), not udevices.
After this change struct clk is accessible from udevice and udevice from
struct clk.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
