The X-Powers AXP313a is a small PMIC with just three buck converters and
three LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow
drivers to adjust voltages.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
commit 95168d77d391 ("sunxi: add Allwinner R528/T113 SoC support") added
the new entry out of order.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
CONFIG_ARCH_SUNXI will not be enabled for RISC-V SoCs using this driver.
Use the symbol for the driver itself instead.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A power domain id on sandbox should be in the range from zero to
ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic.
Addresses-Coverity-ID: 467401 ("Out-of-bounds write")
Addresses-Coverity-ID: 467405 ("Out-of-bounds read")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)")
Fixes: 81bd22e935dc ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
This file uses errno return values in functions, so include <errno.h>
here rather than rely on indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sandbox has <asm/barrier.h> and defines nop() there we should
include that in our driver for clarity and then remove our local nop()
from <k210/pll.h>.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Much of the functionality of fastboot relies on being able to run
commands as defined in the environment. This means it does depend on
CMDLINE being enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
While it is nice to have the font command, using 'select' makes it
impossible to build the console code without it. Stop using 'select' and
make it default if CONSOLE_TRUETYPE is enabled when asking the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to do a DFU update over TFTP we need to have some network
device available, so make this depend on NETDEVICES
Signed-off-by: Tom Rini <trini@konsulko.com>
The following patch migrates the usage of debug and printf functions
to the relevant logging function as per U-Boot DM guidelines.
Additionally some of the debugging statements have been rearanged for
a more meaningfull debug experience.
aarch64-linux-gnu-size reports 229 bytes less when debug is enabled at
file level, while is just 5bytes more when disabled.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@amd.com>
Link: https://lore.kernel.org/r/20231013123739.2757979-1-ibai.erkiaga-elorza@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When 64-bit address is passed only lower 32-bit address
is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011031515.4151-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Unhandled error coming from xilinx_pm_request() but return
value is not read back that's why getting sparse warning
as below:
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
In case of error return the "ret" value.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011025647.17200-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f315c ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
-----BEGIN PGP SIGNATURE-----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=qtcH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20231106' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fixup to also enabled DFU RAM boot for libretech-ac
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
One well-known sm child device that provides secure power control is the
Secure Power Controller. This device utilizes SMC calls to communicate
with power domains on the secure monitor side.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Since we sync device tree with Linux, we have to add this
clock definition for USB stack.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra uses built in Power Management Controller (PMC) to perform
CPU reset. Code to perform this was located in mach-tegra, so lest
create DM driver to handle this.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
