Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
Variable $fdtfile needs to be set for automatically loading a device-tree
from the ESP or boot partition.
* Set CONFIG_DEFAULT_FDT_FILE in the defconfig.
* Add $fdtfile to the default environment.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Acer Iconia A500 is a tablet computer designed, developed and
marketed by Acer Inc. It is powered by 1 GHz Nvidia Tegra 2 processor
and 1GB DDR2 RAM. The A500 is sold with 64 GB, although both 16 GB
and 32 GB models are available.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add usb_pgood_delay to ensure proper detection of USB devices.
Increase the USB power good delay on the SOM boards, as this
is required for certain USB sticks otherwise, they may not
be detected.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250107122915.1378284-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for the R-Car S4 Starter Kit with R8A779F4 SoC support.
This implementation natively uses OF_UPSTREAM to pull in most recent
DT. The defconfig is derived from S4 Spider, with reduced UART baud
rate to 921600 Bdps. The DT alias to rswitch is removed as the alias
should point to rswitch ports, not to rswitch itself, see [1].
[1] https://lore.kernel.org/linux-arm-kernel/20250118111344.361617-5-marek.vasut+renesas@mailbox.org/
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series add support for MediaTek MT7987 SoC with its reference
boards and related drivers.
This patch series add basic boot support on eMMC/SD/SPI-NOR/SPI-NAND for these
boards. The clock, pinctrl drivers and the SoC initializaton code are also
included.
Link: https://lore.kernel.org/r/cover.1737621362.git.weijie.gao@mediatek.com
This patch adds general board files based on MT7987 SoC.
MT7987 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with one spi controller.
So three configs are need for these boot types:
1. mt7987_rfb_defconfig - SPI-NOR (spi2) and SPI-NAND (spi0)
2. mt7987_emmc_rfb_defconfig - eMMC + SPI-NOR (spi2)
3. mt7987_sd_rfb_defconfig - SD + SPI-NOR (spi2)
Note: spi2 also supports booting from SPI-NAND, but not the default option.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add initial support for Marvell PXA1908. The SoC has 4 Cortex-A53 cores,
a GC7000UL GPU and a variety of peripheral controllers.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
When building without DHCP/PXE configurations (NET disabled),
compilation errors may occur due to mismatched bootargs.
Ensure bootargs related to DHCP/PXE are not enabled if the
corresponding commands are disabled.
include/config_distro_bootcmd.h:443:9: error: expected ‘}’ before
‘BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE’
443 | BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Chanho Park <parkch98@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Radxa ROCK 5C[1] is a Rockchip RK3588S2 based single board computer.
[1] https://radxa.com/products/rock5/5c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Khadas Edge2 is a Rockchip RK3588S based SBC (Single Board Computer)
by Khadas.
There are tree variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MP4 GPU
3x MIPI CSI 4x lanes
2x MIPI-DSI DPHY 4x lanes
32/64GB eMMC
1x USB 2.0, 1x USB 3.0, 2x USB-Type-C
1x HDMI 2.1 output, 1x DP 1.4 output
USB PD over USB Type-C
Kernel commit:
04d552993522 ("arm64: dts: rockchip: Add Khadas edge2 board")
Signed-off-by: Jacobe Zang <jacobe.zang@wesion.com>
Align R-Car Gen2/Gen3/Gen4 configuration header file to look
basically the same way across these three SoC generations.
There are subtle difference between the remaining bits in
those files across SoC generations, but the common bits are
now aligned. There is not much left in those headers either,
most of the configuration is now converted to Kconfig.
Specifically for R-Car Gen3, GIC registers have been moved
to architecture specific header file rcar-gen3-base.h , the
rest of the changes here are comment changes and indentation
changes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add basic support for SpacemiT's Banana Pi F3 board.
Update the k1.dtsi align with mainline.
Note that the device tree files follow the mainline Linux source[1].
Links: https://patches.linaro.org/project/linux-serial/patch/20240730-k1-01-basic-dt-v5-8-98263aae83be@gentoo.org/ [1]
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Signed-off-by: Huan Zhou <pericycle.cc@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Without this patch, there will be error indicating that
"Cannot use 64 bit addresses with SDMA", and the booting
process will stuck.
please see full boot log below
U-Boot 2022.04-g18185931 (Sep 11 2024 - 13:15:30 +0800)
SoC: LS1028AE Rev1.0 (0x870b0010)
Clock Configuration:
CPU0(A72):1500 MHz CPU1(A72):1500 MHz
Bus: 400 MHz DDR: 1600 MT/s
Reset Configuration Word (RCW):
00000000: 3c004010 00000030 00000000 00000000
00000010: 00000000 018f0000 0030c000 00000000
00000020: 020031a0 00002580 00000000 00003296
00000030: 00000000 00000010 00000000 00000000
00000040: 00000000 00000000 00000000 00000000
00000050: 00000000 00000000 00000000 00000000
00000060: 00000000 00000000 200e705a 00000000
00000070: bb580000 00000000
Model: LS1028A RDB Board
Board: LS1028AE Rev1.0-RDB, Version: C, boot from SD
FPGA: v8 (RDB)
SERDES1 Reference : Clock1 = 100.00MHz Clock2 = 100.00MHz
DRAM: 3.9 GiB
DDR 3.9 GiB (DDR4, 32-bit, CL=11, ECC on)
Using SERDES1 Protocol: 47960 (0xbb58)
PCIe1: pcie@3400000 Root Complex: no link
PCIe2: pcie@3500000 Root Complex: x1 gen2
Core: 45 devices, 22 uclasses, devicetree: separate
WDT: Started watchdog@c000000 with servicing (60s timeout)
WDT: Started watchdog@c010000 with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
EEPROM: Invalid ID (ff ff ff ff)
In: serial
Out: serial
Err: serial
SEC0: RNG instantiated
Net:
Warning: enetc-0 (eth0) using random MAC address - d2:9b:a5:37:7b:b5
eth0: enetc-0
Warning: enetc-2 (eth1) using random MAC address - ca:57:11🇩🇪de:cb
, eth1: enetc-2, eth2: swp0, eth3: swp1, eth4: swp2, eth5: swp3
Hit any key to stop autoboot: 0
Trying load HDP firmware from SD..
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 18944, count 512 ... 512 blocks read: OK
Loading hdp firmware from 0x00000000a0000000 offset 0x0000000000002000
Loading hdp firmware Complete
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk mmc@2140000.blk...
Scanning disk mmc@2150000.blk...
Found 7 disks
ERROR: invalid device tree
Found EFI removable media binary efi/boot/bootaa64.efi
981992 bytes read in 44 ms (21.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
WARNING could not find node vivante,gc: FDT_ERR_NOTFOUND.
Booting /efi\boot\bootaa64.efi
Cannot use 64 bit addresses with SDMA
Error reading cluster
** Unable to read file /efi/boot/grubaa64.efi **
Unexpected return from initial read: Device Error, buffersize 29D790
Failed to load image ￢ : Device Error
start_image() returned Device Error
EFI LOAD FAILED: continuing...
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
Scanning mmc 1:2...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@3100000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@3110000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@3100000 for devices... 1 USB Device(s) found
scanning bus usb@3110000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
Trying load from SD ...
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 32768, count 81920 ... 81920 blocks read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
The size of J7200 tiboot3.bin is 516KB but the memory reserved for it in
HyperFlash was 512KB. This led to overlap of tiboot3.bin over tispl.bin
region and break in HyperFlash boot mode.
Therefore, fix this by increasing the memory allocated for tiboot3.bin
to 1MB for J7200.
Fixes: cf1d6867f774 ("board: ti: j7200: Introduce support for j7200 build targets")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
Wadim Egorov <w.egorov@phytec.de> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/20241127121736.1525948-1-w.egorov@phytec.de
Move the environment into the board directory and convert header to a
txt file. In addition, this patch also applies following changes:
- Change default nfsroot path to /srv/nfs due to compliance with Linux
FHS 3.0.
- Rename specific variables as stated in the bootstd documentation.
Renamed variables:
fdt_addr => fdt_addr_r
fdt_file => fdtfile
Signed-off-by: Yunus Bas <y.bas@phytec.de>
The current A/B switching preparatory altbootcmd is confusing
to users, replace it with plain 'run bootcmd' which can be
replaced by proper A/B switching altbootcmd when the matching
updater is added on top of the platform. By default, keep the
boot counter incrementing, but do not do any A/B partition
switching.
Signed-off-by: Marek Vasut <marex@denx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/23573
Android:
- bootstd: Implement bootimage v2 support
- bootstd: Support non-A/B in bootmeth_android
- Migrate VIM3 and VIM3L to use bootmeth_android
- bootstd: Additional test for bootimage v2
- bootstd: Optimize load time when reading partitions
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As things have been moved to Kconfig there are a number of dead comments
left over in x530.h. Remove them.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use standard boot instead of the distro boot scripts. Regenerate the
board defconfig now that some options are selected automatically.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove CFG_SYS_BAUDRATE_TABLE as there's no reason not to use the
defaults defined via config_fallbacks.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Actually khadas vim3 use distro command to boot android image.
Move on new bootmeth android for A/B and non-A/B vim3 android.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Link: https://lore.kernel.org/r/20241126-adnroidv2-v4-4-11636106dc69@baylibre.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Actually khadas vim3l use distro command to boot android image.
Move on new bootmeth android for A/B and non-A/B vim3l android.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Link: https://lore.kernel.org/r/20241126-adnroidv2-v4-3-11636106dc69@baylibre.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Get the memory region information from system controller to reduce the
number of platform specific headers. We were aligned on NXP mek board
implementation. This need at least 1 header per memory configuration.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
We have many HW with capricorn i.MX8X boards. The difference in u-boot is
at all by the display of the LEDs.
* put upstream a reference project & board for DT and defconfig
* use the capricorn prefix outside the board/siemens/capricorn folder
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/23474
- UFS support is enabled for SC7280 and SM8150 platforms.
- Qualcomm dt-bindings headers are all dropped in favour of
dts/upstream.
- The SMMU driver now correctly handles stream ID 0 and is disabled in
EL2.
- Initial support for capsule updates (using the new dynamic UUIDs) is
added for the RB3 Gen 2 board alongside a new SCSI backend for DFU.
- CONFIG_PINCONF is enabled in qcom_defconfig.
- The vqmmc supply is now enabled for sdcard support on boards that need
it.
- A quirk is added for reading GPIOs on the PM8550 PMIC
Qualcomm boards flash U-Boot a variety of partitions, implement support
for determining which slot U-Boot is running from, finding the correct
partition for that slot and configuring the appropriate DFU string.
Initially, we only support the RB3 Gen 2 where U-Boot is flashed to the
UEFI partition, and ignore handling of slots. In the future we will
additionally support booting U-Boot from other partitions (e.g. boot)
and correct handling for A/B.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
These fields are currently set on exactly two platforms today, and used
by only one of them. Update pic32mzdask to use CFG_SYS_SRAM* in the one
location it needs it and otherwise drop this field from the bd_info
struct.
Signed-off-by: Tom Rini <trini@konsulko.com>
