Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62px
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62x
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
BeaglePlay.
Note this involved creating BeaglePlay's own beagleplay.h board header file
instead of reusing am62_evm's.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
SK-TDA4VM.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM64x
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.
It provides the following feature set:
* up to 16GB LPDDR4x
* on-module eMMC
* SD card (on a baseboard) via edge connector
* Gigabit Ethernet with on-module GbE PHY
* HDMI/eDP
* MIPI-DSI
* 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
* HDMI input over FPC connector
* CAN
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 host
* PCIe
- 1x PCIe 2.1 Gen3, 4 lanes
- 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
* on-module ATtiny816 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
* on-module Secure Element with Global Platform 2.2.1 compliant
JavaCard environment
The support is added for Tiger on Haikou devkit, similarly to RK3399
Puma and PX30 Ringneck.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ArmSoM Sige7 is a Rockchip RK3588 based SBC (Single Board Computer) by
ArmSoM.
There are two variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MC4 GPU
2x MIPI CSI 2 multiple lanes connector
64GB/128GB on board eMMC
uSD slot
1x USB 2.0 Type-A, 1x USB 3.0 Type-A, 1x USB 3.0 Type-C
1x HDMI 2.1 output
2x 2.5 Gbps Ethernet port
40-pin IO header including UART, SPI and I2C
USB PD over USB Type-C
Size: 92mm x 62mm
Kernel commit:
81c828a67c78 (arm64: dts: rockchip: Add ArmSom Sige7 board)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for different RAM sizes and speed grades on the
phyCORE-i.MX8MP.
Add support for 1GB 1.5GHz, 1GB 2GHz, 4GB 1.5GHz,
4GB 2GHz and 8GB 2GHz RAM.
The RAM size and speed grade is detected by the information
stored in the EEPROM on the SoM.
Co-developed-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Co-developed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Co-developed-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By removing the "boot" directory in the "m53menlo/boot/fitImage" path,
we simplify the TFTP server directory layout a bit. This also requires a
change to the mmcload command as it (mis-)uses the same variable as the
TFTP boot.
Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The ethernet PHY on MX8Menlo board takes a while to come out of
reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Switch to using bootstd. Note that with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Also config_distro_bootcmd.h header file that is no longer needed in
j721s2_evm.h.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The constraints on the MMC_SUPPORTS_TUNING symbol can easily be
expressed in Kconfig (with the addition of SPL_MMC_SUPPORTS_TUNING).
Furthermore, in order to remove <common.h> from the MMC subsystem, the
way this symbol is used today needs to be changed in order to continue
functioning.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When u-boot enable CONFIG_SYS_BOOT_RAMDISK_HIGH, rootfs image relocated
from FIU address space to memory address before jump to kernel.
Since Arbel reserved memory from 0x00000000 to 0x06200000 for tip image,
and rootfs image may too large that cannot found a suitable location
before 128MB(0x8000000), so increase mapping size from 128MB to 192MB.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Remove not needed variables from environment.
- boot_scripts is not needed, the default value is just fine and
already includes boot.scr
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
In commit 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
the empty definition of fdt_fixup variable was removed, however this was
still referenced from the boot command leading to boot failures:
## Error: \"fdt_fixup\" not defined`
Fix this by removing "run fdt_fixup" from the boot command and instead
enable CONFIG_OF_ENV_SETUP in the defconfig that would achieve the same
but in a more robust way (it works fine even if the variable is not
defined).
Fixes: 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Janne Grunau <j@jannau.net> says:
This series contains a few misc config changes for Apple silicon
systems:
- switch from the deprecated distro boot scripts to standard boot
- allows EFI console resizing based on the video console size
- enables 16x32 bitmap fonts as Apple devices come with high DPI
displays
- enables 64-bit LBA addressing
Use standard boot instead of the distro boot scripts. Use
BOOTSTD_FULL instead of BOOTSTD_DEFAULTS for easier interactive use.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
The display size querying in efi_console relies on this order. The
display should be the primary output device and should be used to
display more than 80x25 chars.
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
Drop the distro-boot scripts and use standard boot instead.
Inspired by:
'commit 7755dc58af7b ("rockchip: Move to standard boot")'
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZiUXVA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLR5AJ9g6i7STLs6+13Oa1RF0OVucjRaHwCfUsdodreO
NWJ4C4sWE4l/KeEjbLY=
=IiTw
-----END PGP SIGNATURE-----
Merge tag 'video-20240421' of https://source.denx.de/u-boot/custodians/u-boot-video
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
Remove not needed variables from environment and include config files.
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
- boot_file, kernel_file, ip_dyn variables are not used anywhere
- fdt_fixup variable is just set empty
- defargs, vidargs variables used to be used from some bootscript,
however there is no point on having it here and even old legacy
bootscript can work without them
- removed CONFIG_ENABLE_DDR_TRAINING_DEBUG, this is a leftover from
some copy/paste
On colibri imx6ull/imx7 NAND module, remove consoleblank=0, this is
already the Linux kernel default therefore useless.
Various Linux Kernel command line options removed are not-existing
left-over that applied to some old NXP i.MX downstream branch
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmX8JnYcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFfPB/4g0YTnWiI0ENLumM+Q
RwcfIZJZ9YS49QPGil04i8+3TKH9b/vJZc6oyeKBQ1ZYis/kgcUHFFeMjZek8Ou5
yKd/zj861sRmRSBPD5WCSPx4YX1V6xln64vlYTvjeWs1auRuj16sPOcacxlpR6J/
p95DMt0EF5kUzCPD1WbZC6fIMhyXJT7OD1NiIJXCQT6w1hnkS2pC3Y5fiPsyR9yz
7R7yQ+hJyWBp/KsYNcgDpINSQqDSis5dd4RD/2felQ6kKGvZfuDW5pK2LyL0xAt0
Q+jNoaMw8nJQ/RxH7WbbVd0lKX0S94t/PRlCLVQkZRoWsioQ9puT38ToKTRq3yvS
2Omr
=GQJV
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2024.07 cycle:
- This feature set includes a new board named sama7g54 Curiosity.
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
This patch is to enable Agilex5 platform for Intel
product. Changes, modification and new files are
created for board, dts, configs and makefile to
create the base for Agilex5.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Move the environment into the board directory and convert it from a C
header to a text file. Sort the variables alphabetically.
No functional changes.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
Move ROCK Pi 4 specific board code from the shared evb_rk3399 target
into its own board target and update related defconfigs to use the new
TARGET_ROCKPI4_RK3399 option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This architecture and related board are unmaintained currently and have
been for a long time. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
