The default j7200 devicetree and k3_avs driver set 2GHz/1GHz frequency
for A72/MSMC clks and the OPP_NOM voltage.
J7200 SOCs may support OPP_LOW Operating Performance Point:
1GHz/500MHz clks for A72/MSMC and OPP_LOW AVS voltage read from efuse.
Hence, add a config check in board_init_f() to select OPP_LOW specs:
- Check if OPP_LOW AVS voltage read from efuse is valid.
- Use the device IDs and clock IDs (TISCI docs [0]) to find the A72 and
MSMC clock frequencies in the devicetree.
- Fixup the clock frequencies in devicetree as per OPP_LOW spec.
k3_avs driver programs the OPP_LOW AVS voltage for VDD_CPU through
k3_avs_notify_freq() callback from clk_k3.
[0]: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
k3_avs driver checks opp_ids when probing and overwrites the voltage
values in vd_data for the respective board. The new k3_avs_check_opp()
can be called from board files to check the efuse data and returns 0 if
valid.
Also add the same check in k3_avs_program_voltage() to error out if
the efuse data was not valid.
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
Add OPP_LOW frequency->voltage entry to vd_data.
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
OPP_NOM corresponds to OPP_1 and OPP_LOW to OPP_0 efuse register
fields, as described in the Datasheet [0]
The register offsets and fields are described in the TRM (5.2.6.1.5
WKUP_VTM_VD_OPPVID_j Register) [1].
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
[1]: https://www.ti.com/lit/pdf/spruiu1 (J7200 TRM)
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
The j7200 SOC has a single DDR controller and hence no need for
configuring the MSMC interleaver. Hence we do not have an explicit node
for MSMC in j7200 DT, unlike j721s2/j784s4.
Also, MSMC clk id is described under A72SS0_CORE0 Device in TISCI
documentation [0].
Considering the above, define the MSMC clk in the a72 node.
[0]: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html#clocks-for-a72ss0-core0-device
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Enable AVS support on J784S4 along with regulator.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add the VTM node to the R5 boot stage so that AVS is correctly
configured for AM68 SK.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add VTM node to R5 boot stage so that AVS gets correctly configured for
J784S4 EVM and AM69 SK.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Currently in _dm_gpio_set_flags() when set_flags ops is not implemented
direction_output()/_input() is used, but pull up/down is not supported by
these ops.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Avoid crashing U-Boot when the GPIO controller for a button is disabled
or failed to probe. We also need to check the priv data for each button
since even if a button fails to probe it will still be polled by the
core code.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Introduce CONFIG_PHYTEC_K3_DDR_PATCH to make DDR timing patch code
optional for PHYTEC K3 boards. This allows better control over which
boards receive DDR timing patches, rather than compiling the code for
all boards with K3_DDRSS enabled.
Also enable the feature by default for PHYCORE_AM62X_R5.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The ST M24256E behaves as a regular M24C256, except for the E variant
which uses up another I2C address for Additional Write lockable page.
This page is 64 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C256 area separately as that is on separate
I2C address from this page.
Unlike M24C32-D and M24C64-D, this part is specifically ST and does not
have any comparable M24* counterparts from other vendors, hence the st,
vendor prefix. Furthermore, the part name is M24256E without C between
the 24 and 256, this is not a typo. Finally, there is M24C256-D part,
which does contain 32 Bytes long Additional Write lockable page, which
is a different part and not supported by this patch.
Datasheet: https://www.st.com/resource/en/datasheet/m24256e-f.pdf
From Linux kernel commit:
339cb28b9ee6 ("eeprom: at24: add ST M24256E Additional Write lockable page support")
Signed-off-by: Marek Vasut <marex@denx.de>
Given that ARCH_SUNXI already implies that USB_GADGET should be enable,
we should also imply USB being enabled.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Given that OF_LIBFDT is library functionality, the feature of EFI_LOADER
needs to select OF_LIBFDT rather than depend on it being already
enabled.
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
It is not the case that we can only pick ASPEED_AST2500 if DM_RESET
is enabled, but rather choosing ASPEED_AST2500 means we must select
DM_RESET.
Signed-off-by: Tom Rini <trini@konsulko.com>
With this pull request support for the EFI_HTTP_PROTOCOL and
EFI_IP4_CONFIG2 protocols are added. This allows EFI applications
to load files via HTTP.
UEFI:
add efi_dp_from_ipv4 function
add efi_net_set_addr, efi_net_get_addr functions
add support for HTTP device path
set EFI bootdevice device path to HTTP when loaded from wget
add support to send http requests and parse http headers
provide EFI_IP4_CONFIG2_PROTOCOL
provide EFI_HTTP_PROTOCOL
support IPv4() in device path to text protocol
provide unit tests for the HTTP and IPv4 Config2 protocols
Network:
zero terminate string with headers in wget_fill_info()
zero terminate string with headers in wget_lwip_fill_info()
pass port and server_name via wget_ctx in lwIP network stack
let wget_with_dns work with dns disabled
Others:
Add HTTP and IPV4 Config II protocols to UUID library functions.
-----BEGIN PGP SIGNATURE-----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=Wa3j
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2024-12-04' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/23707
With this pull request support for the EFI_HTTP_PROTOCOL and
EFI_IP4_CONFIG2 protocols are added. This allows EFI applications
to load files via HTTP.
UEFI:
add efi_dp_from_ipv4 function
add efi_net_set_addr, efi_net_get_addr functions
add support for HTTP device path
set EFI bootdevice device path to HTTP when loaded from wget
add support to send http requests and parse http headers
provide EFI_IP4_CONFIG2_PROTOCOL
provide EFI_HTTP_PROTOCOL
support IPv4() in device path to text protocol
provide unit tests for the HTTP and IPv4 Config2 protocols
Network:
zero terminate string with headers in wget_fill_info()
zero terminate string with headers in wget_lwip_fill_info()
pass port and server_name via wget_ctx in lwIP network stack
let wget_with_dns work with dns disabled
Others:
Add HTTP and IPV4 Config II protocols to UUID library functions.
Add a test for the EFI_IP4_CONFIG2_PROTOCOL. The test sets the ip
policy to static, adds an ip address, and then reads the current
ip address and checks for it to be the same as the one that was set.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Add an EFI HTTP driver. This commit implements the
EFI_HTTP_PROTOCOL and the EFI_HTTP_SERVICE_BINDING_PROTOCOL.
The latter is attached to the handle of th efi network
device. This is the same handle where snp, pxe, and ipconfig
are attached to.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Add an implementation of the EFI_IP4_CONFIG2_PROTOCOL. The protocol
is attached to the handle of the efi network device. This is the same
handle where snp and pxe are attached to.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Add network-stack agnostic way to send an http request and
parse http headers from efi drivers. This uses wget as a
backend and communicates with it via efi_wget_info.
The function efi_net_do_request allocates a buffer on behalf of an
efi application using efi_alloc and passes it to wget to receive
the data. If the method is GET and the buffer is too small, it
re-allocates the buffer based on the last received Content-Length
header and tries again. If the method is HEAD it just issues one
request. So issuing a HEAD request (to update Content-Length) and
then a GET request is preferred but not required.
The function efi_net_parse_headers parses a raw buffer containing
an http header into an array of EFI specific 'http_header' structs.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Set the device path of the efi boot device to an HTTP device path
(as formed by efi_dp_from_http) when the next boot stage is loaded
using wget (i.e., when wget is used with wget_info.set_bootdev=1).
When loaded from HTTP, the device path should account for it so that
the next boot stage is aware (e.g. grub only loads its http stack if
it itself was loaded from http, and it checks this from its device path).
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add efi_dp_from_http to form a device path from HTTP. The
device path is the concatenation of the device path returned
by efi_dp_from_ipv4 together with an URI node and an END node.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add the functions efi_net_set_addr and efi_net_get_addr to set
and get the ip address from efi code in a network agnostic way.
This could also go in net_common, or be compiled conditionally
for each network stack.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Implement Ipv4() node support in the device path to text protocol.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add efi_dp_from_ipv4 to form a device path from an ipv4 address.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This was marked as TODO in the code:
- Enable use of wget_with_dns even if CMD_DNS is disabled if
the given uri has the ip address for the http server.
- Move the check for CMD_DNS inside wget_with_dns.
- Rename wget_with_dns to wget_do_request
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
This patch comes as a companion to the same patch but for the legacy
net stack. Commit 1327c2a8d6 ("net/lwip: wget: integrate struct wget_info
into wget code") introduced function wget_fill_info() which retrieves
the headers from the HTTP server response. As we want to parse the
string in later patches we need to ensure that it is NUL terminated.
We must further check that wget_info->headers in not NULL.
Otherwise a crash occurs.
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Commit 2dd076a9c1b4 ("net: wget: integrate struct wget_info into legacy
wget code") introduced function wget_fill_info() which retrieves the
headers from the HTTP server response. As we want to parse the string in
later patches we need to ensure that it is NUL terminated.
We must further check that wget_info->headers in not NULL.
Otherwise a crash occurs.
Fixes: 2dd076a9c1b4 ("net: wget: integrate struct wget_info into legacy wget code")
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Commit 5907c81 ("net: lwip: Enable https:// support for wget") was not
correctly rebased on top of the changes introduced by Commit 6cc4d04
("net/lwip: wget: put server_name and port into wget_ctx") in next.
This commit re-applies a couple of lines from 6cc4d04.
Fixes: Commit 5907c81 ("net: lwip: Enable https:// support for wget")
Signed-off-by: Adriano Cordova <adrianox@gmail.com>
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZ0m53AAKCRDKSWXLKUoM
Ie4PAJ4r7EHkSngpW3QdBEb15aLxN1pC4ACcC9DDGGn04kCTChpv0CEi/kRLUBU=
=Veyg
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2025.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2025.04-rc1
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
Tom Rini <trini@konsulko.com> says:
Hey all,
This is picking up Simon's v5 of the above-named series and making a few
more changes so that the follow-up series I have leads to arm64 being
supported for almost all jobs. To quote Simon's cover letter:
All gitlab runners are currently amd64 machines. This series attempts to
create a docker image which can also support arm64 so that sandbox tests
can be run on it.
The TARGET_... environment variables for grub could perhaps be adjusted,
using the new variables, but I have not done that for now.
Adding to what Simon said, we now build grub for all architectures as
the reason to install it was to be able to use the binaries in QEMU.
That won't provide us with amd64 binaries on arm64 hosts so we can't use
that shortcut anymore.
Link: https://lore.kernel.org/r/20241127172247.1488685-1-trini@konsulko.com
PSCI reset is not implemented in Exynos850 EL3 firmware. Disable it to
fix the reset in cases where it can be used, e.g. when running EFI
selftest.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a list of possible platforms that can be used by gitlab runners.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Refactor the code to support downloading toolchains for arm64 as well as
x86_64
There doesn't seem to be an xtensa toolchain for arm64 at the same
location, so download that only on x86
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix a warning due to the syntax used for PYTHONPATH:
LegacyKeyValueFormat: "ENV key=value" should be used instead of
legacy "ENV key value" format (line 304)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
We no longer need to install libc6-i386 so we can drop that. Switch to
installing linux-image-generic as that will be available on all hosts,
to provide the /boot/vmlinu* file that's requires for various tools.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add instructions on how to build the file for multiple architectures.
Add a message indicating what is happening.
Update the documentation as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of deleting /var/lib/apt/lists after each relevant RUN line, use
a cache mount as is the current best practices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
For consistency now, and future ease of testing with non-amd64 hosts,
build grub for all architectures rather than relying on host binaries
for i386/x86_64.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The current release of grub is 2.12 and it will be good to pick this up
now so that we can update other parts of our stack.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We had a few places that were not using "make -j$(nproc)" but instead
just plain "make" and so slowing down the overall build.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add in the x86_64 toolchain, but do not enforce using it for sandbox.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
