Implement the .get_function operation, so the gpio command can report
the current function. Since the GPIOF_FUNC (versus GPIOF_UNUSED) mux
values vary among the PMICs, report all non-GPIO mux values as UNKNOWN.
Signed-off-by: Samuel Holland <samuel@sholland.org>
There are three major variants of the AXP PMIC GPIO functionality (plus
PMICs with no GPIOs at all). Except for GPIO3 on the AXP209, which uses
a different register layout, it is straightforward to support all three
variants with a single driver. Do this, and in the process remove the
GPIO-related definitions from the PMIC-specific headers, and therefore
the dependency on AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC driver implements the DM_PMIC uclass, those functions
can be used instead of the platform-specific "pmic_bus" functions.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it still depends on one of those
choices, and therefore also AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC has a DM driver and binds device tree subnodes, the
GPIO device can be bound that way, instead of from inside board code.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it does not differentiate among
the supported compatibles.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This is less confusing than half of the driver using "axp_gpio" and the
other half using "gpio_axp".
Signed-off-by: Samuel Holland <samuel@sholland.org>
These PMICs each have two GPIO pins, and are supported by the axp_gpio
driver. In order to convert the axp_gpio driver to probe using the
device tree, the corresponding device tree nodes must be present. Add
them, following the same binding as the AXP209 and AXP813.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, we can switch to DM_GPIO for these pins with no loss in
functionality. Since the driver now gets its pin configuration from
the device tree, we can remove the Kconfig symbols.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove
it, along with the rest of the support for AXP virtual GPIOs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the USB PHY driver uses the device tree to get VBUS supply
regulators, these Kconfig symbols are unused. Remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <samuel@sholland.org>
On many boards, the USB ports are powered by a GPIO-controlled fixed
regulator. In preparation for switching the USB PHY driver to use the
regulator uclass instead of driving the GPIO directly, ensure these
boards have fixed regulator support enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
On many boards, the USB ports are powered by the PMIC's "drivevbus"
regulator. In preparation for switching the USB PHY driver to use the
regulator uclass instead of a virtual GPIO pin, ensure these boards
have AXP PMIC regulator support enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that some regulator driver exists for this PMIC, add support for
probing regulator drivers from the device tree subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The first AXP regulator converted to use the regulator uclass is the
drivevbus switch, since it is used by the USB PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.
The following six boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Nintendo_NES_Classic_Edition_defconfig /
sun8i-r16-nintendo-nes-classic-edition
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
None of those six boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Since the D1 CCU binding is defined, we can add support for its
gates/resets, following the pattern of the existing drivers.
Series-to: sunxi
Signed-off-by: Samuel Holland <samuel@sholland.org>
Compatible strings for some new RTC hardware variants were added to
the binding. Add them to the driver in preparation for supporting
those new SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The clock and reset drivers use the exact same platform data. Simplify
them by sharing the object. This is safe because the parent device
(the clock device) always gets its driver model callbacks run first.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The reason here is the same as the reason for changing the clock driver:
platform data can be provided when binding the driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
All of the driver private data should really be platform data since it
is determined statically (selected by the compatible string or extracted
from the devicetree). Move everything to platform data, so it can be
provided when binding the driver. This is useful for SPL, or for
instantiating the driver as part of an MFD.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that all of the variants use the same bind/probe functions and ops,
there is no need to have a separate driver for each variant. Since most
SoCs contain two variants (the main CCU and PRCM CCU), this saves a bit
of firmware size and RAM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Because the gate arrays are not given explicit sizes, the arrays are
only as large as the highest-numbered gate described in the driver.
However, only a subset of the CCU clocks are needed by U-Boot. So there
are valid clock specifiers with indexes greater than the size of the
arrays. Referencing any of these clocks causes out-of-bounds access.
Fix this by checking the identifier against the size of the array.
Fixes: 0d47bc705651 ("clk: Add Allwinner A64 CLK driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
The reset array size is currently used for bounds checking in the reset
driver. The same bounds check should really be done in the clock driver.
Currently, the array size is provided to the reset driver separately
from the CCU descriptor, which is a bit strange. Let's do this the usual
way, with the array sizes next to the arrays themselves.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the H6 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This commit also adds the following new board devicetrees:
- sun50i-h6-pine-h64-model-b.dts
- sun50i-h6-tanix-tx6-mini.dts
This update should not impact any existing U-Boot functionality.
Series-to: sunxi
Cover-letter:
sunxi: Devicetree sync from Linux v5.18-rc1
This series brings all of our devicetrees up to date with Linux.
Older SoCs (before A83T) have not been synchronized in over 3 years.
And I don't have any of this hardware to test. But there are not major
changes to those devicetrees either.
The big motivation for including older SoCs in this update is converting
the USB PHY driver to get its VBUS detection GPIO/regulator from the
devicetree instead of from a pin name in Kconfig. Many older boards had
those properties added or fixed since the last devicetree sync. This PHY
driver change is necessary to complete the DM_GPIO migration.
A couple of breaking changes were made to several SoCs' devicetrees in
Linux relating to the "r_intc" interrupt controller. New kernels support
old devicetrees, but not the other way around. So to be most compatible
and avoid regressions, those changes are skipped here.
END
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A64 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree for the R40/T3 SoC verbatim from the Linux v5.18-rc1
tag. None of the existing boards had any devicetree updates.
This commit adds the following new board devicetrees:
- sun8i-r40-oka40i-c.dts
- sun8i-t3-cqa3t-bv3.dts
Signed-off-by: Samuel Holland <samuel@sholland.org>
