The USB3 related DT nodes in SoC u-boot.dtsi is slightly different from
the final nodes being targeted for Linux kernel v6.10.
Sync USB3 related nodes from Linux maintainer v6.10-rockchip-dts64-1 tag
to prepare for migration of RK3588 to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The usb-typec related nodes and props added in the board u-boot.dtsi
file has not yet landed in upstream Linux kernel DT, and they are not
needed for U-Boot to use the USB Type-C port in peripheral mode.
Remove superfluous usb-typec related nodes and props and replace them
with a simple dr_mode and maximum-speed prop to cleanup the board
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK356x boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RK356x boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- anbernic-rgxx3-rk3566: Multi device target
- generic-rk3568: Generic target only meant for U-Boot use
- pinetab2-rk3566: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a <CONFIG_SYS_SOC>-u-boot.dtsi file that gets included by default
for RK356x boards when a board specific u-boot.dtsi file dont exists.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3399 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3399 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate RK3399 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following target is not migrated to use OF_UPSTREAM:
- nanopi-m4-2gb-rk3399: DDR3 variant of nanopi-m4-rk3399 (LPDDR3)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3328 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3328 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3328 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3308 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3308 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3308 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the obsolete ethernet0 alias now that all board device tree files
have been fully synced with Linux kernel v6.8.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Sync rk3399-pinephone-pro device tree from Linux kernel v6.8.
Add SPI flash related node and options to support boot from SPI flash.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Add SYS_NS16550_MEM32=y to use readl/writel for serial console.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-pinebook-pro device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rockpro64 device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-4 related device tree from Linux kernel v6.8.
Add SPI flash related nodes and options to support boot from SPI flash.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support SATA HAT.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-khadas related device tree from Linux kernel v6.8.
Add SPI flash related options to support booting from SPI flash.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock960 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support PCIe SATA boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y and DM_REGULATOR_GPIO=y, boards does not use
pwm-regulator or regulator-gpio compatible.
Add USB_XHCI_HCD=y, USB_DWC3=y and USB_DWC3_GENERIC=y to support USB3.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-nanopi-4 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support M4 SATA HAT.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, boards does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-roc-pc related device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=30000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-orangepi device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-firefly device tree from Linux kernel v6.8.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-evb device tree from Linux kernel v6.8.
Drop bootph prop for i2c0 and rk808 node, PMIC support is not included
in TPL/SPL and PMIC regulators are working fine in U-Boot proper.
Change to use sdmmc_cd pinconf and drop cd-gpios for card detect pin.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-leez-p710 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-eaidk-610 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-n10 related device tree from Linux kernel v6.8.
Remove SPL_GPIO=y, board does not use gpio in SPL.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-puma related device tree from Linux kernel v6.8.
The vdd_log node is already part of rk3399-puma.dtsi, only keep the
regulator-init-microvolt prop in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-gru related device tree from Linux kernel v6.8.
The spi_flash symbol is no longer part of upstream DT, it is re-defined
to allow existing reference use in related u-boot.dtsi-files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync RK3399 SoC common .dtsi-files from Linux kernel v6.8.
The ethernet0 alias is moved to rk3399-u-boot.dtsi in this patch, the
alias will be added in board specific .dts-files and finally removed
from rk3399-u-boot.dtsi in following patches.
The rng node is replaced with crypto0 and crypto1, both can supply
random numbers.
There is no other intended change with this patch.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-cru.h with one from Linux kernel v6.2+ and fix use of the
SCLK_DDRCLK name that was only used by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A few boards have shown to be required to properly configure pinctrl
for the fixed regulator gpio pin used by sdmmc before being able to read
from SD-cards.
Include the related gpio, regulator and pinctrl nodes and enable related
Kconfig options so that pinctrl can be configured in SPL for boards that
may be affected by such issue.
Also change to imply SPL_DM_SEQ_ALIAS for all boards because it must be
enabled for working gpio usage in SPL after a future DT sync.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The initial serial console UART iomux is typically configured in
board_debug_uart_init() at TPL stage on Rockchip platform.
Later stages typically use pinctrl driver to configure iomux UART once
again based on the control FDT.
Include uart related pinctrl nodes in TPL/SPL control FDT to make it
possible for pinctrl driver to configure UART iomux at TPL/SPL stage.
Following debug log message may also be seen at U-Boot pre-reloc stage:
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This can be resolved by including bootph prop for U-Bood pre-reloc
phase (bootph-some-ram or bootph-all). However, this has intentionally
been excluded due to including it unnecessarily slows down boot around
200-400 ms.
Also add the clock-frequency prop similar to what has been done for
other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3399-puma is the only supported board that use uart0 for serial
console, other RK3399 boards typically use uart2 for serial console
and may use uart0 for bluetooth.
Move setting bootph prop to board u-boot.dtsi to only include the uart0
node in TPL/SPL control FDT for the rk3399-puma target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vop nodes should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort nodes alphabetically by name, symbol or reg addr in RK3399 related
u-boot.dtsi files. Also remove one of the duplicated &pmu nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove superfluous bootph-all props already inherited from main soc
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A lot of RK3399 boards use a u-boot,spl-boot-order of "same-as-spl",
&sdhci and &sdmmc.
Move this to rk3399-u-boot.dtsi and make this default for boards
currently missing a u-boot,spl-boot-order prop.
Before commit a7e69952eb6d ("rockchip: spl: Cache boot source id for
later use") it was required to include the SPI flash node in the
u-boot,spl-boot-order prop to successfully load FIT from SPI flash.
The SPI flash node reference has been dropped from spl-boot-order from
pinebook-pro, roc-pc and rockpro64 now that "same-as-spl" also gets
resolved to the SPI flash node and loading FIT from SPI flash works
without having the node explicitly referenced in spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The TPL and/or SPL control FDT on RK3399 boards does not contain any
node with a compatible that is supported by driver/misc/ drivers.
Remove use of xPL_MISC_DRIVERS options to stop including e.g an unused
efuse driver in TPL and/or SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Imply OF_LIBFDT_OVERLAY Kconfig options to add device tree overlay
support on all RK3399 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Imply support for GbE PHY status parsing and configuration when support
for onboard ethernet is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The RK3399 SoC contain a crypto engine block that can generate random
numbers.
Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the
random generator on all RK3399 boards. Also remove the unnecessary use
of a status = "okay" prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The RK3399 SoC support the ARMv8 Cryptography Extensions, use of ARMv8
crypto can speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation to almost all RK3399 boards.
The following boards have been excluded:
- chromebook_bob: SPL max size limitation of 120 KiB
- chromebook_kevin: SPL max size limitation of 120 KiB
Also imply OF_LIVE to help speed up init of U-Boot proper and disable
CONFIG_SPL_RAW_IMAGE_SUPPORT on leez-rk3399 to ensure SPL does not try
to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This follows the example of RISC-V where <asm/global_data.h> includes
<asm/u-boot.h> directly as "gd" includes a reference to bd_info already
and so the first must include the second anyhow. We then remove
<asm/u-boot.h> from all of the places which include references to "gd"
an so have <asm/global_data.h> already.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from the remainder of the files under arch/arm and
when needed add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all fsl-layerscape related files and when needed
add missing include files directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-aspeed files and when needed add missing
include files directly.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
