The root oscillators reference used to be in rcc node since
3d15245502c4 ("ARM: dts: stm32mp1: explicit clock reference needed by RCC clock driver")
however this is not part of upstream stm32mp151.dtsi . The
RCC driver does need this reference, reinstate it locally.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The root oscillators reference used to be in rcc node since
3d15245502c4 ("ARM: dts: stm32mp1: explicit clock reference needed by RCC clock driver")
however this is not part of upstream stm32mp151.dtsi . The
RCC driver does need this reference, reinstate it globally.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit 61ff13283c3b ("board: sl28: move to OF_UPSTREAM") USB0 is
broken because the former u-boot soc dtsi was setting dr_mode to "host"
but the linux device tree isn't. That is because linux fully supports
OTG but u-boot doesn't. Therefore, u-boot only ever enabled host mode
and never OTG mode. Add it to our board "-u-boot.dtsi" to fix it.
Fixes: 61ff13283c3b ("board: sl28: move to OF_UPSTREAM")
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
Wadim Egorov <w.egorov@phytec.de> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/20241127121736.1525948-1-w.egorov@phytec.de
The correct spelling is R-Car, including the dash, update the usage.
Comment change only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page. Add
aliases eeprom0wl and eeprom1wl for the access to the EEPROM ID
page node.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Bryan Brattlof <bb@ti.com> says:
Hello Everyone!
This small series converts TI's AM65x reference board to use
CONFIG_OF_UPSTREAM and removes the unused device tree files from
arch/arm/dts.
Because it's the last board using a AM65x without enabling OF_UPSTREAM
it allows us to also remove all the SoC FDT files as well and keep a
single version of the SoC's DT files in the dts/upstream directory going
forward.
Link: https://lore.kernel.org/r/20241121-am65x-v1-0-fe87aff1b5fc@ti.com
Rather than rely on manual updates from the arch/arm/dts directory,
enable CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the am65x reference board.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Updated PLL driver sequencing requires us to use udelay in the PLL
driver as there is no poll bit to get the status of operations.
tick-timer(mcu_timer0/main_timer0) setting up the clocks for itself is
something that won't work as the PLL driver will be using udelay and
PLLs are configured during clock probe which would end up in a recursive
probe.
tick-timer being used by K3 devices are configured by ROM and we really
don't need to configure any of the clocks.
Remove the clock dependency from R5 stage as we don't need to setup
clocks for it.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Aniket Limaye <a-limaye@ti.com> says:
This series adds OPP_LOW spec data in k3_avs driver and enables a config
option to select the OPP_LOW performance point.
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
The default j7200 devicetree and k3_avs driver set OPP_NOM spec
frequency and voltage.
In the board init file, if K3_OPP_LOW config is enabled, Check if
OPP_LOW AVS voltage read from efuse is valid and update frequency (A72
and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec.
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
Test logs:
https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075
- With series applied on master and CONFIG_K3_OPP_LOW enabled in
j7200_evm_r5_defconfig
- Logs shown with and without efuse register programmed for OPP_0
(Errors out if OPP_0 not found, programs OPP_LOW spec if found)
- Voltage update verified using 'i2c md 0x4c 0xe' in u-boot
- Frequency update verified using 'k3conf clock dump' in linux
Link: https://lore.kernel.org/r/20241119003617.1871183-1-a-limaye@ti.com
The j7200 SOC has a single DDR controller and hence no need for
configuring the MSMC interleaver. Hence we do not have an explicit node
for MSMC in j7200 DT, unlike j721s2/j784s4.
Also, MSMC clk id is described under A72SS0_CORE0 Device in TISCI
documentation [0].
Considering the above, define the MSMC clk in the a72 node.
[0]: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html#clocks-for-a72ss0-core0-device
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add the VTM node to the R5 boot stage so that AVS is correctly
configured for AM68 SK.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add VTM node to R5 boot stage so that AVS gets correctly configured for
J784S4 EVM and AM69 SK.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
It doesn't make sense for these files to have the x bit set. It was,
probably accidentally, added in:
Fixes: 2c494e62c31a (arm: dts: Stratix10: Add QSPI node)
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Enable PCIe/NVMe support on Data Modul i.MX8M Mini eDM SBC. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
The YModem support in SPL was never really used on this device,
the SDP support is much more convenient on i.MX8M Mini based
hardware. Replace the YModem support with SDP support.
The SDP can be utilized by forcing the board into SDP boot mode
by grounding test point right next to silkscreen label U30, and
then by using mfgtools 'uuu -brun spl flash.bin' once the device
enumerates on host system USB bus. The SDP capable USB port is
available on the USB micro-B port on the base board.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DRAM configuration GPIO straps must be accessible in SPL and before
relocation because the GPIOs are sampled both in U-Boot SPL as well as early
on in U-Boot proper. The already present bootph-pre-ram DT property made the
GPIO controllers available in SPL, but not early on in U-Boot proper, which
made gpio_request_list_by_name_nodev() in board dmo_get_memcfg() fail. Add
missing bootph-some-ram DT property to all GPIO controllers which are
referenced in dmo,ram-coding-gpios DT property to make those GPIO
controllers available early in U-Boot proper as well.
Fixes: 8c103c33fb14 ("dm: dts: Convert driver model tags to use new schema")
Signed-off-by: Marek Vasut <marex@denx.de>
u-boot.itb has been generated via mkimage_fit_atf.sh but it is on the way
out that's why convert it's description to binman.
Compare to script binman description is not able to configure BL31 and BL32
load/entry addresses which should be done separately.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/90b613796aee38158252c8bb1dfc3da0420f089d.1730452668.git.michal.simek@amd.com
There is necessary to do some steps to compose boot images. These steps
were in scripts in layers for a while. That's why introduce description via
binman to simplify wiring and remove all scripting around.
This should make sure that everybody is up2date with the latest versions.
The first step is to create fit image with DTBs with descriptions in
configuration node which is written as regular expression to match all SOM
versions.
Description is there for k24 and k26 in spite of low level psu_init
configuration is different. The reason is that it goes to u-boot.itb image
which is the same for k24 and k26.
u-boot.itb is another image which is generated. It is normally generated
via arch/arm/mach-zynqmp/mkimage_fit_atf.sh but this script is supposed to
be deprecated.
FIT image by purpose is using 64bit addresses to have default option to
move images to high DDR (above 4GB). TF-A and TEE are optional components
but in the most cases TF-A is present all the time and TEE(OP-TEE) is used
by some configurations too.
3rd generated image is boot.bin with updated user field which contains
version number. This image can be used with updated Image Selector
which supports A/B update mechanisms with rollback protection.
4th image is image.bin which binary file which contains boot.bin and
u-boot.itb together and can be programmed via origin Image Selector.
This image can be also used for creating one capsule which contains both
boot images (in SPL boot flow).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/35bc47a4a4799c5f5dbea56a45340a2810538330.1730452668.git.michal.simek@amd.com
Make use of OF_UPSTREAM which uses Linux dts.
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
The phyCORE-i.MX 93 is available in various variants. Relevant variant
options for the spl/u-boot are:
- with or without HS400 support for the eMMC
- with 1GB ram chip, or 2GB ram chip
The phyCORE's eeprom contains all information about the existing variant
options. Add evaluation of the eeprom data to the spl/u-boot to
enable/disable HS400 and to select the appropriate ram configuration at
startup.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
current generated flash.bin image does not longer
boot on cxg3 board.
Rename bootph-pre-ram to bootph-all so flash.bin
boots again!
Add u-boot specific change (add bootph-all property)
in A35_0 node to imx8qxp-capricorn-u-boot.dtsi
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
We have many HW with capricorn i.MX8X boards. The difference in u-boot is
at all by the display of the LEDs.
* put upstream a reference project & board for DT and defconfig
* use the capricorn prefix outside the board/siemens/capricorn folder
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
