Introduce simple led.rst documentation to document all the additional
Kconfig and the current limitation of LED_BLINK and GPIO software blink.
Also add missing definition for sw_blink in led_uc_plat struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace CONFIG_USB_USB_GADGET by CONFIG_USB_GADGET_DOWNLOAD.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass <sjg@chromium.org> says:
This series includes the patches needed to make make the EFI 'boot' test
work. That test has now been split off into a separate series along with
the EFI patches.
This series fixes these problems:
- sandbox memory-mapping conflict with PCI
- the fix for that causes the mbr test to crash as it sets up pointers
instead of addresses for its 'mmc' commands
- the mmc and read commands which cast addresses to pointers
- a tricky bug to do with USB keyboard and stdio
- a few other minor things
Sandbox keeps a table of addresses which map to pointers which are
outside its emulated DRAM. The current range from 10000000 conflicts
with the PCI range, meaning that if PCI mapping is on, that particular
address can be decoded by PCI instead of the table.
Fix this by moving the range up to the top of memory. Update the docs
while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The mmc erase command currently requires blk# and cnt parameters
which can be obtained using the part start and part size commands
if the entire partition needs to be erased.
Simplify the use of the mmc erase command by allowing the partition
name to be specified directly.
Signed-off-by: Tomas Paukrt <tomaspaukrt@email.cz>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
We shouldn't have had the link to our git tree be contained within "``"
as that meant that it did not work as a link, so remove those. And
rather than make this a link plus text, keep this as a link within the
text for overall clarity.
Suggested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
UEFI:
* Use generated UUIDs in UEFI capsules:
- efi: define struct efi_guid
- lib: uuid: add UUID v5 support
- efi: add a helper to generate dynamic UUIDs
- doc: uefi: document dynamic UUID generation
- sandbox: switch to dynamic UUIDs
- lib: uuid: supporting building as part of host tools
- include: export uuid.h
- tools: mkeficapsule: use u-boot UUID library
- tools: mkeficapsule: support generating dynamic GUIDs
- test: lib/uuid: add unit tests for dynamic UUIDs
- test: lib/uuid: add tests for UUID version/variant bits
* Minor code clean-up
- shorten efi_bootmgr_release_uridp_resource()
- rename efi_bootmgr_image_return_notify
- return the correct error in efi_bootmgr_release_uridp()
- Kconfig: clean up the efi configuration status
- Use puts() in cout so that console recording works
- Put back copyright message in helloworld.c
-----BEGIN PGP SIGNATURE-----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=mncs
-----END PGP SIGNATURE-----
Merge tag 'efi-next-20241024' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request efi-next-20241024
UEFI:
* Use generated UUIDs in UEFI capsules:
- efi: define struct efi_guid
- lib: uuid: add UUID v5 support
- efi: add a helper to generate dynamic UUIDs
- doc: uefi: document dynamic UUID generation
- sandbox: switch to dynamic UUIDs
- lib: uuid: supporting building as part of host tools
- include: export uuid.h
- tools: mkeficapsule: use u-boot UUID library
- tools: mkeficapsule: support generating dynamic GUIDs
- test: lib/uuid: add unit tests for dynamic UUIDs
- test: lib/uuid: add tests for UUID version/variant bits
* Minor code clean-up
- shorten efi_bootmgr_release_uridp_resource()
- rename efi_bootmgr_image_return_notify
- return the correct error in efi_bootmgr_release_uridp()
- Kconfig: clean up the efi configuration status
- Use puts() in cout so that console recording works
- Put back copyright message in helloworld.c
The current documentation for the bootcount API is on our website and
not the old wiki, update the link in two places.
Signed-off-by: Tom Rini <trini@konsulko.com>
In two places we had references to the old wiki pages instead of links
to the relevant part of our documentation. Update (and slightly reword)
these spots.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove both the ELDK and emdebian links as they are broken, and add a
link to the kernel.org toolchains which we use in CI.
Signed-off-by: Tom Rini <trini@konsulko.com>
The previous wording on the paragraph about what branch to use when
submitting patches did not reflect how / when the next branch is
currently used. Reword this to note that master should be used for bug
and regression fixes, always, and that next should be used once it
opens, with -rc2.
Reported-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add support for generating GUIDs that match those generated internally
by U-Boot for capsule update fw_images when using dynamic UUIDs.
Dynamic UUIDs in U-Boot work by taking a namespace UUID and hashing it
with the board compatible and fw_image name. This feature just provides
a way to determine the UUIDs for a particular board without having to
actually boot U-Boot on it.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Document how platforms can generate GUIDs at runtime rather than
maintaining a list of UUIDs per-board.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The process here is almost identical to the Dragonboard 410c, we've come
full circle!
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Sughosh Ganu <sughosh.ganu@linaro.org> says:
This is a follow-up from an earlier RFC series [1] for making the LMB
and EFI memory allocations work together. This is a non-rfc version
with only the LMB part of the patches, for making the LMB memory map
global and persistent.
This is part one of a set of patches which aim to have the LMB and EFI
memory allocations work together. This requires making the LMB memory
map global and persistent, instead of having local, caller specific
maps. This is being done keeping in mind the usage of LMB memory by
platforms where the same memory region can be used to load multiple
different images. What is not allowed is to overwrite memory that has
been allocated by the other module, currently the EFI memory
module. This is being achieved by introducing a new flag,
LMB_NOOVERWRITE, which represents memory which cannot be re-requested
once allocated.
The data structures (alloced lists) required for maintaining the LMB
map are initialised during board init. The LMB module is enabled by
default for the main U-Boot image, while it needs to be enabled for
SPL. This version also uses a stack implementation, as suggested by
Simon Glass to temporarily store the lmb structure instance which is
used during normal operation when running lmb tests. This does away
with the need to run the lmb tests separately.
The tests have been tweaked where needed because of these changes.
The second part of the patches, to be sent subsequently, would work on
having the EFI allocations work with the LMB API's.
[1] - https://lore.kernel.org/u-boot/20240704073544.670249-1-sughosh.ganu@linaro.org/T/#t
Notes:
1) These patches are on next, as the alist patches have been
applied to that branch.
2) I have tested the boot on the ST DK2 board, but it would be good to
get a T-b/R-b from the ST maintainers.
3) It will be good to test these changes on a PowerPC platform
(ideally an 85xx, as I do not have one).
The TCG event log buffer is being set at the end of ram memory. This
region of memory is to be reserved as LMB_NOMAP memory in the LMB
memory map. The current location of this buffer overlaps with the
memory region reserved for the U-Boot image, which is at the top of
the usable memory. This worked earlier as the LMB memory map was not
global but caller specific, but fails now because of the overlap.
Move the TCG event log buffer to the start of the ram memory region
instead. Move the location of the early trace buffer and the load
buffer for U-Boot(spl boot) accordingly.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently uclass index is used for bind/unbind which ignores alias
sequence numbering. Use device sequence number instead as it's
the number explicitly set in the DT.
Also update documentation to use sequence number.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently uclass index is shown in DM tree dump which ignores alias
sequence numbering. The result could be confusing since these 2 numbers
could be different. Show device sequence number instead as it's more
meaningful.
Also update documentation to use sequence number.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass <sjg@chromium.org> says:
This series started as a small fix for checking for an empty line,
but in the process several other problems were found and fixed:
- fix tests which use console recording but don't set the flag
- drop unnecessary resetting of the console in tests
- drop unnecessary blank line before MMC output
- update the docs a little
- fix buildman test failure on newer Pythons
- a few other minor things
This series also renames the confusing flag names, so that they are
easier to remember - just a UTF_ (unit-test flags) prefix.
The _REC suffix doesn't add much. Really what we want to know is whether
the test uses the console, so rename this flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Most tests don't have this. It helps to keep the test declaration
clearly associated with the function it relates to, rather than the next
one in the file. Remove the extra blank line and mention this in the
docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
The UT_TESTF_ macros read as 'unit test test flags' which is not right.
Rename to UTF ('unit test flags').
This has the benefit of being shorter, which helps keep UNIT_TEST()
declarations on a single line.
Give the enum a name and reference it from the UNIT_TEST() macros while
we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This information is useful for people looking at how U-Boot has changed
over the years and the design decisions which led to it. Move it into
doc/ in an 'historical' section.
Signed-off-by: Simon Glass <sjg@chromium.org>
eMMC is enabled on E850-96 board now. Mention that in the board
documentation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update the bindings doc for Exynos DW MMC block to follow the upstream
example and reflect the latest changes made in corresponding Linux
kernel bindings.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
current env_set_default_vars() doesn't delete
var that are not in the imported env. hashtable
removes vars that are not in the imported
env but present in the current env only if H_NOCLEAR
flag is not set.
This change is to avoid passing H_NOCLEAR flag if
specific vars are passed to env_set_default_vars()
Without this change:
Marvell>> env default boot_mode
Marvell>>
With the change:
Marvell>> env default boot_mode
WARNING: 'boot_mode' not in imported env, deleting it!
Signed-off-by: Ravi Minnikanti <rminnikanti@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some boards don't have chipselect lines for leds so cs-gpios is not
specified in the dts leading to probing error. Fix it by making
behavior similar to the one in Linux, parse num-chipselects and
if it is zero, ignore cs-gpios.
Signed-off-by: Michael Polyntsov <michael.polyntsov@iopsys.eu>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
The Rock 5 ITX is a board in ITX form factor using the RK3588 SoC
It can be powered either by 12V, ATX power-supply or PoE.
Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key slot,
2*2.5Gb PCIe-connected Ethernet NICs.
Display options are 2*HDMI, DP via USB-c, eDP + 2*DSI via PCB connectors.
USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
connector.
Schematics for the board can be found on
- https://dl.radxa.com/rock5/5itx/radxa_rock_5_itx_X1100_schematic.pdf
- https://dl.radxa.com/rock5/5itx/v1110/radxa_rock_5itx_v1110_schematic.pdf
The naming scheme with the dashes follows Dragan's comment on the mainline
devicetree commit:
"the name of this board deviates from the standard Radxa naming scheme,
which is something like "ROCK <number><letter>" thus, "rock-5a" is
fine, but it should be "rock-5-itx", simply because there's a space
between "5" and "ITX" in "ROCK 5 ITX"
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add a 'upl' command to work with Universal Payload features. For now it
only supports reading and writing a handoff structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based
on the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
Features tested on a CM3588 NAS Kit with 8GB RAM 64GB eMMC module:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
The two hw revisions use different io-voltage for Ethernet PHY and can
be identified using GPIO4_C4:
- v1.1.1: x (internal pull-down)
- v2.1: PHY_RESET (external pull-up)
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both hw revisions.
Minimal DTs that includ DT from dts/upstream is added to support booting
from both hw revision and only set Ethernet PHY io-voltage when the hw
revision is detected at runtime. A side-affect of this is that defconfig
show OF_UPSTREAM=n, however dts/upstream DTs is used for this board.
Features tested on Orange Pi 3B 4GB (v1.1.1 and v2.1):
- SD-card boot
- eMMC boot
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB host
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both board models.
Features tested on a ZERO 3W 8GB v1.11:
- SD-card boot
- eMMC boot
- USB gadget
- USB host
Features tested on a ZERO 3E 4GB v1.2:
- SD-card boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
