Similar to RK35xx the BootRom in RK3328 can read all data and look for
idbloader at 0x8000, same as it does for SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace the rockchip,cryptov1-rng compatible with compatibles used in
the linux device tree for RK3288, RK3328 and RK3399 to ease sync of SoC
device tree from linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3328 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there is a fallback to
read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card will fail:
U-Boot SPL 2024.04-rc1 (Feb 05 2024 - 22:18:22 +0000)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use a common FIT load order, same-as-spl > SD-card > eMMC on
RK3328 boards. Only EVB and Radxa ROCK Pi E is affected by this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation"), bootph-pre-ram doesn't make U-Boot proper
bind the device before relocation.
While this is usually not much of an issue, it is when there's a lookup
for devices by code running before the relocation. Such is the case of
env_init() which calls env_driver_lookup() which calls
env_get_location() which is a weak symbol and may call
arch_env_get_location() also a weak symbol. Those are two functions that
may traverse UCLASS to find some devices (e.g.
board/theobroma-systems/common/common.c:arch_env_get_location()).
This allows something in the env_init() call stack to be able to use
uclasses for SD and eMMC controller on RK3588S/RK3588. This aligns the
behavior with what seems to be all SoCs except RK356x family.
Additionally, if any other env function (e.g. env_load) were to be used
before relocation, this is also required as otherwise it wouldn't be
able to find the MMC device(s).
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The device tree has evolved over time, so re-sync. This also
partial reverts one change on the PCIe, because U-Boot doesn't
have a proper driver. However, since the clock is configured
to generate a 100MHz reference clock by default, a proper driver
isn't really necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Much like we have for ATF, OP-TEE has a standard address that we load
it too and run it from. Add a Kconfig item for this to remove some
hard-coding and allow this address to be more easily changed.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Allow boards that use ti_spl_template to not use optee part in
configuration.
Vendor can have module with 256 Mb of memory and they try to optimize
the available memory just using the essential components.
This change allow to remove tee from configuration without binman
fail.
configurations {
default = "conf-0";
conf-0 {
description = "k3-am62_ccm_m3";
firmware = "atf";
loadables = "dm", "spl";
fdt = "fdt-0";
};
};
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The phy calibration pattern partition isn't needed as the Cadence driver isn't
calibrating the phys.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Fixes: 58d61fb5a77e ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Add bootph DT tags to enable OSPI in SPL.
Set OSPI regs for R5 SPL to address OSPI's boot region.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
SolidRun Armada-388 SoM has an i2c bus supporting on-som eeprom, and
peripherals on a carrier.
armada-38x.dtsi disables this bus by default, it should be enabled by
som or carrier dts.
Linux has moved i2c0 from helios-4 board dts to som dtsi, including
status, pinctrl and clock speed.
Copy these settings from mainline.
This fixes accessing i2c bus from u-boot commandline.
Signed-off-by: Josua Mayer <josua@solid-run.com>
The Turris Omnia contains the Marvell 88E6176 ethernet switch. Add
config options and device tree to enable the support.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Introduce the base dts files needed for u-boot or to augment the linux
dtbs for use in the u-boot-spl and u-boot binaries.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Introduce the base dts files needed for u-boot or to augment the linux
dtbs for use in the u-boot-spl and u-boot binaries.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[ add binman and ddr dtsi files ]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Commit 5d7a95f49999 ("imx6ul/imx6ull: synchronise device trees with
linux") removed the display timings from the board device tree whereas
they are still needed by the mxsfb driver.
Add the timings back (the correct ones) in the
imx6ul-opos6uldev-u-boot.dtsi file and remove them from the
opos6uldev.env file.
Update the opos6uldev_defconfig file so that the LCD turns on at boot.
Fixes: 5d7a95f49999 ("imx6ul/imx6ull: synchronise device trees with linux")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The OrangePi Zero 2W is a tiny development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of LPDDR4 DRAM, a mini-HDMI connector,
two USB Type-C sockets and a 16MB SPI NOR flash.
There is an FPC connector to connect an expansion board, which sports
two more USB Type-A sockets and a 100MBit Ethernet port. Support for
the expansion board is not in the DT yet, probably a DT overlay would
cover this in the future.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Drop the U-Boot specific DTS in favour of upstream. We'll only include
the -4000 variant as that is what U-Boot already supported.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard820c.dts file in favour of the
upstream apq8096-db820c.dts and an additional -u-boot.dtsi with the
U-Boot specific additions.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Don't use hardcoded clock IDs, use the IDs from the dt-bindings to be
compatible with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import PM8994 and PMI8994 DTSI files in preparation for switching
MSM8996 boards to upstream DTS.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard410c.dts in favour of the upstream
msm8916-sbc.dts. No additional changes are needed to this DTS for U-Boot
support.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the supporting pm8916.dtsi and msm8916-pm8916.dtsi files from
upstream in preparation for switching boards over.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import sdm845.dtsi from upstream, as well as the upstream DTS files for
the db845c and Samsung starqltechn. Delete the old board files.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the PM8998 and PMI8998 PMIC DTSI files from Linux as well
as the common audio codec in preperation for replacing board DTS files
with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot,
in many cases to the specific SoC but also to the board itself (e.g.
memory map). This has been largely resolved by modernising the Qualcomm
drivers in U-Boot, however the board code still largely follows this
model.
This patch removes the board specific memory maps and duplicated board
init code, replacing it with generic init code.
The memory map is now built at runtime based on data read from DT, this
allows for the memory map to be provided without having to recompile
U-Boot. Support is also added for booting with appended DTBs, so that
the first-stage bootloader can populate the memory map for us.
The sdm845 specific init code is dropped entirely, it set an environment
variable depending on if a button was pressed, but this variable wasn't
used in U-Boot, and could be written to use the button command instead.
The KASLR detection is also dropped as with appended dtb, the kaslr seed
can be read directly from the DTB passed to U-Boot.
A new qcom_defconfig is added, with the aim of providing a generic
U-Boot configuration that will work on as many Qualcomm boards as
possible. It replaces the defconfig files for the Dragonboard 845c,
Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as
they still have some board code left.
Similarly, the config headers for db845c, starqltechn, and qcs404-evb
are replaced by a single qcom header.
The previously db410c-specific board_usb_init() function is made to be
generic and is added to mach-snapdragon. While we lack proper modelling
for USB configuration, using a well-known named pinctrl state is a
reasonably generic middleground, and works using upstream DT. This
function will do nothing unless the USB node has a pinctrl state named
"device", in which case it will be set when entering USB peripheral
mode.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the modern helpers to fetch the clock and use the correct property
("clocks" instead of "clock"). Drop the call to pinctrl_select_state()
as no boards have a "uart" pinctrl state and this prints confusing
errors.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust the apq8016 and apq8096 drivers to use the upstream compatible
properties, and adjust the associated dts files in U-Boot.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The same U-Boot binary is compatible with multiple Verdin AM62 board
variants. However, some of the SoC models can only operate at a maximum
speed of 1 GHz.
Previously, the boards with lower-speed grades were running at
overclocked speeds, leading to kernel complaints about unsupported
configurations.
To resolve this issue, the operating speed has been decreased to the
maximum allowable value across all Verdin AM62 board variants. As a
result, there is a regression in overall boot time, increasing by around
200 milliseconds for the faster SoC variant.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Francesco Dolcini <francesco.dolcini@toradex.com> says:
This series fixes two regressions affecting multiple Toradex boards
(i.MX, TI and TEGRA based) and targets the current master, e.g. v2024.04
release.
U-Boot `reset` command is broken on all Tordex i.MX6* based SoMs since
v2023.07, this series fixes it enabling the `wdt-reboot` driver.
Since v2024.04-rc1 reading the Toradex configuration block is not working
properly anymore, the serial number and the hardware version are not read
correctly, preventing the board from functioning correctly (wrong mac address,
wrong DT, ...). This is fixed by reading the config block in `EVT_SETTINGS_R`
and adding a toradex sysinfo driver. In addition to that, we now use a random
mac address in case the config block is invalid.
Reported-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Closes: https://lore.kernel.org/all/CAKZ1LvM45MB8N0CqgU+C7i9=Bjb6kqNTxWo2Tv407HKLWtCMkA@mail.gmail.com/
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Closes: https://lore.kernel.org/all/e40ed93bd8f371ec56b8fc451dcb458f3ce6dcba.camel@toradex.com/
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/all/ZY2ZDWAQuTlRjV9H@francesco-nb/
commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()")
introduced a regression that 'reset' command unable to reset
imx6 and imx6ull based Toradex's modules in the u-boot.
This change enables a watchdog-based sysreset driver for
Toradex's colibri-imx6, colibri-imx6ull (with nand and emmc)
and apalis-imx6 which solves the reset command regression on
these modules.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixes: 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()")
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit introduces support for the Toradex sysinfo driver in U-Boot,
which uses information from Toradex config block to print correct
board model.
In case the Toradex config block is not present sysinfo prints the model
of the board provided by device tree removing per board specific prints.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since meson-gxbb based boards switched to using upstream DT, so drop
redundant files from arch/arm/dts directory. Only *-u-boot.dtsi files
kept in arch/arm/dts directory for these boards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Roger Quadros <rogerq@kernel.org> says:
MUX driver should autoprobe if the device tree has "idle-states"
property. Drop using the custom "u-boot,mux-autoprobe" property
in TI device trees.
As it is present for USB and USB won't work without the MUX
initialized correctly, add "bootph-all" property to MUX nodes.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
