Writing to eMMC using HS200 mode work more reliably then other modes on
RK356x boards.
Add device tree props and enable Kconfig options for eMMC HS200 mode on
the generic RK3566/RK3568 board. Also enable the pinctrl driver in SPL
and add missing rk3568-generic.dtb to Makefile.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Testing has shown that writing to eMMC using DDR52 mode does not seem to
work on RK356x and RK3588 boards.
A simple test of writing a single block to e.g. sector 0x4000 fails:
# Rescan using DDR52 mode
=> mmc rescan 4
# Write a single block to sector 0x4000 fails with ERROR
=> mmc write 20000000 4000 1
With the MMC_SPEED_MODE_SET Kconfig option enabled.
Fix this by removing the mmc-ddr-1_8v prop from sdhci nodes in affected
board u-boot.dtsi files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove unnecessary status props from rk35xx u-boot.dtsi files, regular
device tree files or default value already enable the affected nodes.
Also reorder bootph-pre-ram and clock-frequency props alphabetically in
rk3588s-u-boot.dtsi uart2 node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a default u-boot,spl-boot-order prop to rk3588s-u-boot.dtsi and
remove the prop from board u-boot.dtsi files using the default value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3588 device tree from linux v6.7.
Also drop the rockchip,rk3568-dwc3 compatible now that dwc3-generic
driver support the rockchip,rk3588-dwc3 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Move uart2 bootph-pre-ram and clock-frequency props from board to SoC
u-boot.dtsi. Regular board device tree already enables the uart2 node,
so status prop is dropped from u-boot.dtsi file.
Also remove unnecessary stdout-path = &uart2, regular board device tree
already provide a stdout-path = "serial2:" value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync linux dts files for rv1126 boards from linux v6.8-rc1 tag. Includes
the newly added dts for Sonoff iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmW4mGIcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyBq9B/sHzeh4lWQpyU5CcO8J
WnlRn2blqL/2LzkawD6OvA7WhEYisLh2389q6pPSFqWZS8v1aNgTO4krnPDOG3a5
s7yigcBtg5KsmnM4K89+KZ/BZW4TzrSHIY4P+t1W92QtnFHEzNW/LolG6jBZnz+e
bMzi0uCGR1cgTW4IfLmuq6NajIaAXywdohMxfi/9kiNhQVT03Jux/CGoIvpJ61Bu
OKWX2KNn0o3XXK7UKdZUSzP6CyiRSplQl3eX/0shh9qPR16eSeUqh952zGxlcOZO
PKXvDMl8QxkCzRjXdg3EH2jADoaTB0maq6JutVyY+SoLiYJ9A8BUCLOIMevCVXjK
3BCH
=V29u
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2024.04 cycle:
This set includes some DT alignments and solves a compile issue for
custom nand defconfigs.
Some 32-bit SoCs can use SCP firmware to implement additional PSCI
functionality, such as system suspend. In order to load this firmware
from SPL, we need to generate and use a FIT instead of a legacy image.
Adjust the binman FIT definition so it does not rely on TF-A BL31, as
this is not used on 32-bit SoCs. Instead, after loading the firmware,
U-Boot proper is executed directly. This requires to provide an
entry point property for the U-Boot image node, which confuses some
loaders like sunxi-fel, so protect that to only be used if we have no
BL31.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: filter U-Boot entry point property]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This is a Chinese TV box based on Allwinner H618 SoC.
The DRAM parameters were derived from the values found in a firmware update.
Signed-off-by: Nick Alilovic <nickalilovic@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.8-rc1.
This time only small changes in the existing files, but five new boards
got added, which opens the door for their respective defconfig files.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for WinLink E850-96 board [1]. It's based on Exynos850 SoC
and follows 96boards specification, so it's compatible with 96boards
mezzanine boards [2]. This patch enables next features:
* Serial console
* USI
* PMU (muxing AP UART path)
* Pinctrl
* Clocks
* Timer (ARMv8 architected)
* Reset control
It's quite a minimal enablement. Features like MMC, USB and Ethernet
will be enabled later.
The rationale for config values is as follows:
* TEXT_BASE = 0xf8800000
That's where BL2 loads the U-Boot payload, so TEXT_BASE must be
exactly this value. Overall the memory map is designed in a way to
keep the bootloader in the upper 128 MiB area of RAM, which is
0xf8000000..0xffffffff. That includes bootloader's code, stack,
data, heap, MMU tables, etc. All the memory below that 128 MiB chunk
can be used for storing boot images (0x80000000..0xf8000000).
* CUSTOM_SYS_INIT_SP_ADDR = 0xf8c00000
Just 4 MiB above the TEXT_BASE address, to leave enough space for
U-Boot code and stack itself (grows downwards).
* SYS_LOAD_ADDR = 0x80000000
The beginning of RAM. That's where Linux kernel image must be
loaded.
* SYS_MALLOC_LEN = 0x81f000
8 MiB for malloc() + ENV_SIZE (128 KiB)
* SYS_MALLOC_F_LEN = 0x4000
Increase malloc() pool size available before relocation from 8 KiB
(default) to 16 KiB. Otherwise "alloc space exhausted" message
appears in U-Boot log during board_init_f() stage. There are next
reasons for doing so:
1. Having "bootph-all" flags in some dts nodes leads to binding
those during pre-relocation stage, and binding (DM) uses
dynamic memory allocation
2. clk-exynos850 driver uses CCF clocks, which in turn use dynamic
memory allocation
Device tree file was imported from Linux kernel. All nodes and boot
phase flags added in exynos850-e850-96-u-boot.dtsi are only needed to
enable serial console:
* oscclk -> cmu_top -> cmu_peri: generate UART/USI clocks
* pinctrl_alive and uart1_pins: needed to mux UART pins
* pmu_system_controller: configures AP UART path to uart1_pins
* usi_uart: configures USI block to operate as a UART protocol
* serial_0: enables serial console (UART)
[1] https://www.96boards.org/product/e850-96b/
[2] https://www.96boards.org/products/mezzanine/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Samsung Exynos850 is ARMv8-based mobile-oriented SoC. It features
Cortex-A55 CPU (8 cores) and it's built using 8nm process.
Add Exynos850 support by enabling next features:
* Import Exynos850 SoC dtsi files from Linux kernel
* Add Exynos850 MMU memory map
* Introduce ARCH_EXYNOS9 platform config option
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- Allow i.MX8M Plus DHCOM to operate in overdrive mode.
- Allow i.MX8M Plus eDM SBC to operate in overdrive mode.
- Enable the 'kaslrseed' command on DH i.MX8M Plus DHCOM.
- Select LTO by default on i.MX8M.
- Convert pico-dwarf/hobbit-imx6ul to CONFIG_DM_SERIAL.
- Fix 'reset' command on wandboard.
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The reserved space is extended to 32MB in Linux kernel because
additional space is needed for authorization execution of JIC/RBF file.
U-Boot required to align with Linux.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Port from Linux v6.7-rc4. Should not hurt U-Boot but makes diffing
easier and allows referencing node names in board dts.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Without correct SERDES MUX and Lane control settings
USB0 will be broken. Set the MUX and Lane control devices
to be auto probed so they are configured correctly.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Without correct SERDES MUX and Lane control settings
USB0 will be broken. Set the MUX and Lane control devices
to be auto probed so they are configured correctly.
Fixes: 69b19ca67bcb ("arm: dts: k3-j721e: Sync with v6.6-rc1")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
-----BEGIN PGP SIGNATURE-----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=BoSU
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20240119' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add CMDLINE dependecy for CMD_STM32KEY
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Add BSEC support to STM32MP25 SoC family with SoC information:
- RPN = Device part number (BSEC_OTP_DATA9)
- PKG = package data register (Bits 2:0 of BSEC_OTP_DATA122)
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
In SCMI configuration, usart1 is secure, so all its resources are secured
(clock and reset) and can't be set/unset by non-secure world but by OP-TEE.
Fixes: 6cccc8d396bf ("ARM: dts: stm32: add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
The device tree is taken from the kernel v6.5.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To make automatic Rockchip DT syncing possible from Linux to U-boot prepare
rk3288.dtsi by moving to 64 bit reg size.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
xilinx:
- Enable NFS, WGET, DNS and BLKMAP by default
zynqmp:
- Support new power-management node
- Remove multiple blank lines from DTSes
- Wire multiboot with DFU infrastructure
- Fix i2c-gpio pinctrl group name
- SOM DT changes (phy on kd240, kv260 cleanups
- Cleanup i2c bus on zcu1285
- DT cleanup (fix node names not to use _)
- Fix USB interrupts
- Cleanup zcu100 DT
- Add support for kaslr-seed
zynqmp_r5:
- Fix W=1 issue with missing dir
tools:
- Improve zynqmpimage mkimage support
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZae/pAAKCRDKSWXLKUoM
IadKAJ9p4nP4Fy3DKfRJjpVoFE+7OR9ZUQCfYtWhN5eNKayfxcw9wnvuv/SggFU=
=95oH
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.04-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.04-rc1-v2
xilinx:
- Enable NFS, WGET, DNS and BLKMAP by default
zynqmp:
- Support new power-management node
- Remove multiple blank lines from DTSes
- Wire multiboot with DFU infrastructure
- Fix i2c-gpio pinctrl group name
- SOM DT changes (phy on kd240, kv260 cleanups
- Cleanup i2c bus on zcu1285
- DT cleanup (fix node names not to use _)
- Fix USB interrupts
- Cleanup zcu100 DT
- Add support for kaslr-seed
zynqmp_r5:
- Fix W=1 issue with missing dir
tools:
- Improve zynqmpimage mkimage support
Add pe2201 platform code and the device tree of pe2201 platform board.
The initial support comprises the UART and PCIe.
Signed-off-by: TracyMg_Li <TracyMg_Li@outlook.com>
Changes since v1:
fix space corrupt.
Changes since v2:
switch to bootstd and text environment.
Changes since v3:
add environment variables.
Add support for J721E HS-SE 2.0 device. Make use of the existing
templates and override the phandles for sysfw.itb so that builds do not
fail.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Qualcomm architecture changes:
* Move clock and pinctrl drivers out of mach-snapdragon
* Various clock driver improvements
* Convert PMIC power/reset key driver to use the button API
* Preparetory work for migrating to upstream DT
The core and chnl register ranges were swapped on SDM845. Fix it, and
fetch the register ranges by name instead of by index.
Drop the cosmetic "version" variable and clean up the debug logging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the upstream gpio-ranges property instead of gpio-count, and drop
the bank-name property for Qualcomm boards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The PMIC button driver is a much better representation of the hardware
here, adjust the boards to use upstream DT and the PMIC button driver
instead of exposing the buttons as GPIOs and relying on the GPIO-button
driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
