Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cool Pi CM5 EVB works as a mother board connect with CM5.
CM5 Specification:
- Rockchip RK3588
- LPDDR4 2/4/8/16 GB
- TF scard slot
- eMMC 8/32/64/128 GB module
- SPI Nor 8MB
- Gigabit ethernet x 1 with PHY YT8531
- Gigabit ethernet x 1 drived by PCIE with YT6801S
CM5 EVB Specification:
- HDMI Type A out x 2
- HDMI Type D in x 1
- USB 2.0 Host x 2
- USB 3.0 OTG x 1
- USB 3.0 Host x 1
- PCIE M.2 E Key for Wireless connection
- PCIE M.2 M Key for NVME connection
- 40 pin header
The dts is from linux-6.8 rc1.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[0]https://patchwork.kernel.org/project/linux-rockchip/patch/2450634.jE0xQCEvom@phil/
CoolPi 4B is a rk3588s based SBC.
Specification:
- Rockchip RK3588S
- LPDDR4 2/4/8/16 GB
- TF scard slot
- eMMC 8/32/64/128 GB module
- SPI Nor 8MB
- Gigabit ethernet drived by PCIE with RTL8111HS
- HDMI Type D out
- Mini DP out
- USB 2.0 Host x 2
- USB 3.0 OTG x 1
- USB 3.0 Host x 1
- WIFI/BT module AIC8800
- 40 pin header
The dts is from linux-6.8 rc1.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[0]https://patchwork.kernel.org/project/linux-rockchip/patch/2450634.jE0xQCEvom@phil/
Add Kconfig options to enable support for booting from SPI NOR flash on
Orange Pi R1 Plus boards.
The generated bootable u-boot-rockchip-spi.bin can be written to 0x0 of
SPI NOR flash. The FIT image is loaded from 0x60000, same as on RK35xx
boards.
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1376768 bytes read in 66 ms (19.9 MiB/s)
=> sf update ${fileaddr} 0 ${filesize}
device 0 offset 0x0, size 0x150200
1126912 bytes written, 249856 bytes skipped in 14.22s, speed 100542 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Kconfig options to enable support for booting from SPI NOR flash on
Pine64 Rock64.
The generated bootable u-boot-rockchip-spi.bin can be written to 0x0 of
SPI NOR flash. The FIT image is loaded from 0x60000, same as on RK35xx
boards.
=> sf probe
SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1359872 bytes read in 65 ms (20 MiB/s)
=> sf update ${fileaddr} 0 ${filesize}
device 0 offset 0x0, size 0x14c000
1118208 bytes written, 241664 bytes skipped in 8.516s, speed 163516 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Similar to RK35xx the BootRom in RK3328 can read all data and look for
idbloader at 0x8000, same as it does for SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace the rockchip,cryptov1-rng compatible with compatibles used in
the linux device tree for RK3288, RK3328 and RK3399 to ease sync of SoC
device tree from linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3328 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there is a fallback to
read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card will fail:
U-Boot SPL 2024.04-rc1 (Feb 05 2024 - 22:18:22 +0000)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use a common FIT load order, same-as-spl > SD-card > eMMC on
RK3328 boards. Only EVB and Radxa ROCK Pi E is affected by this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This architecture and related board are unmaintained currently and have
been for a long time. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable OF_UPSTREAM for AM64-EVM and SK-AM64 boards. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.7-rc7).
Signed-off-by: Andrew Davis <afd@ti.com>
Since commit 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation"), bootph-pre-ram doesn't make U-Boot proper
bind the device before relocation.
While this is usually not much of an issue, it is when there's a lookup
for devices by code running before the relocation. Such is the case of
env_init() which calls env_driver_lookup() which calls
env_get_location() which is a weak symbol and may call
arch_env_get_location() also a weak symbol. Those are two functions that
may traverse UCLASS to find some devices (e.g.
board/theobroma-systems/common/common.c:arch_env_get_location()).
This allows something in the env_init() call stack to be able to use
uclasses for SD and eMMC controller on RK3588S/RK3588. This aligns the
behavior with what seems to be all SoCs except RK356x family.
Additionally, if any other env function (e.g. env_load) were to be used
before relocation, this is also required as otherwise it wouldn't be
able to find the MMC device(s).
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
ZynqMP CG series devices only have two cpus. In this
case the interrupt-affinity property has to adapted, because
cpu3 and cpu4 are missing. By adding a label to the pmu fwnode the
interrupt-affinity can be adapted in a device specific DT.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Link: https://lore.kernel.org/r/20240307152956.431104-1-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The device tree has evolved over time, so re-sync. This also
partial reverts one change on the PCIe, because U-Boot doesn't
have a proper driver. However, since the clock is configured
to generate a 100MHz reference clock by default, a proper driver
isn't really necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Much like we have for ATF, OP-TEE has a standard address that we load
it too and run it from. Add a Kconfig item for this to remove some
hard-coding and allow this address to be more easily changed.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Allow boards that use ti_spl_template to not use optee part in
configuration.
Vendor can have module with 256 Mb of memory and they try to optimize
the available memory just using the essential components.
This change allow to remove tee from configuration without binman
fail.
configurations {
default = "conf-0";
conf-0 {
description = "k3-am62_ccm_m3";
firmware = "atf";
loadables = "dm", "spl";
fdt = "fdt-0";
};
};
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The phy calibration pattern partition isn't needed as the Cadence driver isn't
calibrating the phys.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Fixes: 58d61fb5a77e ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Add bootph DT tags to enable OSPI in SPL.
Set OSPI regs for R5 SPL to address OSPI's boot region.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
SolidRun Armada-388 SoM has an i2c bus supporting on-som eeprom, and
peripherals on a carrier.
armada-38x.dtsi disables this bus by default, it should be enabled by
som or carrier dts.
Linux has moved i2c0 from helios-4 board dts to som dtsi, including
status, pinctrl and clock speed.
Copy these settings from mainline.
This fixes accessing i2c bus from u-boot commandline.
Signed-off-by: Josua Mayer <josua@solid-run.com>
The Turris Omnia contains the Marvell 88E6176 ethernet switch. Add
config options and device tree to enable the support.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Introduce the base dts files needed for u-boot or to augment the linux
dtbs for use in the u-boot-spl and u-boot binaries.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Introduce the base dts files needed for u-boot or to augment the linux
dtbs for use in the u-boot-spl and u-boot binaries.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[ add binman and ddr dtsi files ]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Commit 5d7a95f49999 ("imx6ul/imx6ull: synchronise device trees with
linux") removed the display timings from the board device tree whereas
they are still needed by the mxsfb driver.
Add the timings back (the correct ones) in the
imx6ul-opos6uldev-u-boot.dtsi file and remove them from the
opos6uldev.env file.
Update the opos6uldev_defconfig file so that the LCD turns on at boot.
Fixes: 5d7a95f49999 ("imx6ul/imx6ull: synchronise device trees with linux")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The OrangePi Zero 2W is a tiny development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of LPDDR4 DRAM, a mini-HDMI connector,
two USB Type-C sockets and a 16MB SPI NOR flash.
There is an FPC connector to connect an expansion board, which sports
two more USB Type-A sockets and a 100MBit Ethernet port. Support for
the expansion board is not in the DT yet, probably a DT overlay would
cover this in the future.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Drop the U-Boot specific DTS in favour of upstream. We'll only include
the -4000 variant as that is what U-Boot already supported.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard820c.dts file in favour of the
upstream apq8096-db820c.dts and an additional -u-boot.dtsi with the
U-Boot specific additions.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Don't use hardcoded clock IDs, use the IDs from the dt-bindings to be
compatible with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import PM8994 and PMI8994 DTSI files in preparation for switching
MSM8996 boards to upstream DTS.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard410c.dts in favour of the upstream
msm8916-sbc.dts. No additional changes are needed to this DTS for U-Boot
support.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
