Sync rk3399-pinephone-pro device tree from Linux kernel v6.8.
Add SPI flash related node and options to support boot from SPI flash.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Add SYS_NS16550_MEM32=y to use readl/writel for serial console.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-pinebook-pro device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rockpro64 device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-4 related device tree from Linux kernel v6.8.
Add SPI flash related nodes and options to support boot from SPI flash.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support SATA HAT.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-khadas related device tree from Linux kernel v6.8.
Add SPI flash related options to support booting from SPI flash.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock960 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support PCIe SATA boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y and DM_REGULATOR_GPIO=y, boards does not use
pwm-regulator or regulator-gpio compatible.
Add USB_XHCI_HCD=y, USB_DWC3=y and USB_DWC3_GENERIC=y to support USB3.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-nanopi-4 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support M4 SATA HAT.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, boards does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-roc-pc related device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=30000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-orangepi device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-firefly device tree from Linux kernel v6.8.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-evb device tree from Linux kernel v6.8.
Drop bootph prop for i2c0 and rk808 node, PMIC support is not included
in TPL/SPL and PMIC regulators are working fine in U-Boot proper.
Change to use sdmmc_cd pinconf and drop cd-gpios for card detect pin.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-leez-p710 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-eaidk-610 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-n10 related device tree from Linux kernel v6.8.
Remove SPL_GPIO=y, board does not use gpio in SPL.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-puma related device tree from Linux kernel v6.8.
The vdd_log node is already part of rk3399-puma.dtsi, only keep the
regulator-init-microvolt prop in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-gru related device tree from Linux kernel v6.8.
The spi_flash symbol is no longer part of upstream DT, it is re-defined
to allow existing reference use in related u-boot.dtsi-files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync RK3399 SoC common .dtsi-files from Linux kernel v6.8.
The ethernet0 alias is moved to rk3399-u-boot.dtsi in this patch, the
alias will be added in board specific .dts-files and finally removed
from rk3399-u-boot.dtsi in following patches.
The rng node is replaced with crypto0 and crypto1, both can supply
random numbers.
There is no other intended change with this patch.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-cru.h with one from Linux kernel v6.2+ and fix use of the
SCLK_DDRCLK name that was only used by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A few boards have shown to be required to properly configure pinctrl
for the fixed regulator gpio pin used by sdmmc before being able to read
from SD-cards.
Include the related gpio, regulator and pinctrl nodes and enable related
Kconfig options so that pinctrl can be configured in SPL for boards that
may be affected by such issue.
Also change to imply SPL_DM_SEQ_ALIAS for all boards because it must be
enabled for working gpio usage in SPL after a future DT sync.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The initial serial console UART iomux is typically configured in
board_debug_uart_init() at TPL stage on Rockchip platform.
Later stages typically use pinctrl driver to configure iomux UART once
again based on the control FDT.
Include uart related pinctrl nodes in TPL/SPL control FDT to make it
possible for pinctrl driver to configure UART iomux at TPL/SPL stage.
Following debug log message may also be seen at U-Boot pre-reloc stage:
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This can be resolved by including bootph prop for U-Bood pre-reloc
phase (bootph-some-ram or bootph-all). However, this has intentionally
been excluded due to including it unnecessarily slows down boot around
200-400 ms.
Also add the clock-frequency prop similar to what has been done for
other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3399-puma is the only supported board that use uart0 for serial
console, other RK3399 boards typically use uart2 for serial console
and may use uart0 for bluetooth.
Move setting bootph prop to board u-boot.dtsi to only include the uart0
node in TPL/SPL control FDT for the rk3399-puma target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vop nodes should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort nodes alphabetically by name, symbol or reg addr in RK3399 related
u-boot.dtsi files. Also remove one of the duplicated &pmu nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove superfluous bootph-all props already inherited from main soc
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A lot of RK3399 boards use a u-boot,spl-boot-order of "same-as-spl",
&sdhci and &sdmmc.
Move this to rk3399-u-boot.dtsi and make this default for boards
currently missing a u-boot,spl-boot-order prop.
Before commit a7e69952eb6d ("rockchip: spl: Cache boot source id for
later use") it was required to include the SPI flash node in the
u-boot,spl-boot-order prop to successfully load FIT from SPI flash.
The SPI flash node reference has been dropped from spl-boot-order from
pinebook-pro, roc-pc and rockpro64 now that "same-as-spl" also gets
resolved to the SPI flash node and loading FIT from SPI flash works
without having the node explicitly referenced in spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399 SoC contain a crypto engine block that can generate random
numbers.
Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the
random generator on all RK3399 boards. Also remove the unnecessary use
of a status = "okay" prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The phycore-rk3288 can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for rockchip vendor prefix accordingly.
Move device tree nodes required for u-boot to rk3288-phycore-rdk-u-boot.dtsi
such as chosen, i2c_eeprom_id and it's alias.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am62x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Caleb Connolly <caleb.connolly@linaro.org> says:
This is a subset of [1]. With more platform maintainers switching to
OF_UPSTREAM I didn't want to get in the way (it has also proven more
difficult than I hoped to remove only the fully compatible header
files).
This series removes only the dt-bindings headers which contain generic
data like GPIO flags, input event codes, etc.
It then implements support for building all DTBs for a vendor with
OF_UPSTREAM_BUILD_VENDOR. This removes the need to maintain a set list
of DTBs that can be built by U-Boot and opens up the possibility of new
boards becoming supported "by default" just by landing their DT
upstream.
[1]: https://lore.kernel.org/u-boot/20240321-b4-upstream-dt-headers-v2-0-1eac0df875fe@linaro.org
MD Danish Anwar <danishanwar@ti.com> says:
The series introduces device tree and config changes and AM65x
to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
for AM65x in order to load overlay over spl.
The ICSSG2 node is added in device tree overlay so that it remains in
sync with linux kernel.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
The users need to set env variables fw_storage_interface, fw_dev_part,
fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and
partition they want to use to load firmware files from. By default the env
fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these
envs as per their requirements.
Add ICSSG2 overlay and configuration to tispl and u-boot images.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit c07bba7a2c7e ("verdin-am62: move verdin
am62 to OF_UPSTREAM"). A recent upstream patch removes the gpio hog from
the Linux device tree, so we need to add it to the u-boot dtsi. The
following patch will remove the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/20240301084901.16656-1-eichest@gmail.com/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Adds tifsstub binaries, this is required for deepsleep functionality.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rework the flash.bin image generation such that it uses the new binman
nxp_imx8mimage etype. This way, the flash.bin is assembled in correct
order using plain binman, without any workarounds or sections assembled
in special DT node order.
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> # imx8mm_venice
Tested-by: Fabio Estevam <festevam@gmail.com> # imx8mm-evk and imx8mn-evk
Signed-off-by: Marek Vasut <marex@denx.de>
Include imx8mq-u-boot.dtsi in the board -u-boot.dtsi to pull in binman
configuration instead of duplicating it in the board -u-boot.dtsi again.
Drop the duplicate binman configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Some variants of the ROCK Pi 4 series have an SPI flash chip populated
which can be booted from. This patch enables support in U-Boot for
building the image for the SPI flash, support for booting U-Boot from the
SPI flash chip and support in U-Boot for accessing the SPI flash using
`sf` commands.
Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come
populated with an SPI flash chip, but have the footprint on the board so
a user could solder their own to the board. With this patchset applied,
these board variants without an SPI flash chip still boot from MMC.
I have enabled support for both Winbond and XTX SPI flash devices since
different hardware variants have different devices populated:
- `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG`
- `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`
The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI
flash chip from XTX:
=> sf probe
SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
In the interest of supporting all board variants and not regressing
existing users who boot from MMC, I have enabled support for booting from
both SPI flash chip variants in the defconfig and left the environment
storage location as MMC to not break existing users who have the
environment stored on MMC.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
To prepare for ROCK Pi 4A SPI flash support, sync the DTS from Linux which
includes an SPI flash node.
Kernel tag: v6.6-rc1
Kernel commits:
- eddf73029770 ("arm64: dts: rockchip: Enable internal SPI flash for ROCK \
Pi 4A/B/C")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
The vop node should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Fixes: 6794063d5065 ("ARM: dts: rk3328: Enable VOP for bootph-all")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The default pinctrl for UART2 is using M1 iomux, however, all other
supported RK3588 boards in U-Boot use M0 iomux for UART2.
Change to use the M0 pinctrl for UART2 to match other supported boards.
Fixes: b54c3d0dd69b ("rockchip: board: Add minimal generic RK3588S/RK3588 board")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for USB OTG, RockUSB and UMS to the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for booting from SPI flash using the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing emmc_datastrobe and sdmmc0_det pinctrl to fix possible issue
reading from eMMC or SD-card. Also use correct node for mmc1 alias.
Fixes: 683f61a13f16 ("rockchip: board: Add minimal generic RK3566/RK3568 board")
Fixes: 363cbd578169 ("rockchip: rk3568-generic: Enable eMMC HS200 mode")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
