Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
With the introduction of downstream Linux 6.6, the iMX8MP VPU block
control node in DTS was renamed "blk-ctl@38330000" and will not match
the ones found in `node_path_imx8mp` resulting in the node not being
disabled on the VPU-less variants.
Add an extra node_path entry for imx8mp VPU block control that match
with downstream Linux.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX8M and i.MX9 have duplicated fixup_thermal_trips, so move it
to arch/arm/mach-imx/fdt.c to avoid duplicated code.
The critial temperature point for i.MX9 set to "maxc - 5" back to give
some margin.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
disable_cpu_nodes could be reused by i.MX9, so move disable_cpu_nodes
out from mach-imx/imx8m/soc.c to mach-imx/fdt.c and update
disable_cpu_nodes to make it easy to support different socs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8M use PPI for PMU interrupts, there is no reason to update
interrupt-affinity for PMU even interrupt-affinity was wrongly added
to device tree before.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MMU and caches very early on in the boot process on i.MX8M
in U-Boot proper. This allows board_init_f to run with icache and
dcache enabled, which saves some 700 milliseconds of boot time on
i.MX8M Plus based device.
The 'bootstage report' output is below:
Before:
```
Timer summary in microseconds (8 records):
Mark Elapsed Stage
0 0 reset
961,363 961,363 board_init_f
1,818,874 857,511 board_init_r
1,921,474 102,600 eth_common_init
2,013,702 92,228 eth_initialize
2,015,238 1,536 main_loop
Accumulated time:
32,775 dm_r
289,165 dm_f
```
After:
```
Timer summary in microseconds (8 records):
Mark Elapsed Stage
0 0 reset
989,466 989,466 board_init_f
1,179,100 189,634 board_init_r
1,281,456 102,356 eth_common_init
1,373,857 92,401 eth_initialize
1,375,396 1,539 main_loop
Accumulated time:
12,630 dm_f
32,635 dm_r
```
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Staticize intpll_configure(). Add weak board_imx_intpll_override()
function which can be defined at board level to override specific
PLL frequency settings early during boot. This can be used to for
example force faster CPU core clock frequency if the hardware can
handle it.
Example of increasing CPU core clock to 1600 MHz on i.MX8M Plus:
```
int board_imx_intpll_override(enum pll_clocks pll, ulong *freq)
{
if (pll == ANATOP_ARM_PLL)
*freq = MHZ(1600);
return 0;
}
```
Signed-off-by: Marek Vasut <marex@denx.de>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Migrate imx8mn_bsh_smm_s2 and imx8mn_bsh_smm_s2pro boards to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <patrick.barsanti@amarulasolutions.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The PHYCORE_IMX8MP is used by the phyBOARD-Pollux. Migrate board to
OF_UPSTREAM. Linux kernel device tree for the board can be used as is,
corresponding U-Boot device tree files are removed. U-Boot tweaks are
kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
The PHYCORE_IMX8MM is used by the phyBOARD-Polis and the
phyGATE-Tauri-L. Migrate both boards to OF_UPSTREAM. Linux kernel device
trees for both boards can be used as is, corresponding U-Boot device
tree files are removed. U-Boot tweaks are kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-imx, CPU specific sub-directories and
include/asm/arch-mx* files and when needed add missing include files
directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move verdin-imx8mm and verdin-imx8mp to OF_UPSTREAM:
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
The imx8mn-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mm-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mp-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Move to imx8m{m,n,p}-venice to OF_UPSTREAM:
- replace the non-upstream generic imx8m{m,n,p}-venice dt with one of the
dt's from the OF_LIST
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove rudundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
On imx8m[m|p|q].dtsi, upstream Linux uses different names for NPU/VPU
IP block nodes. It leads variants without such HW block having it
enabled by default.
This patch adds the upstream Linux node's paths to the disable list while
keep the compatibility with downstream Linux.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
In an attempt to select ARMV8_SPL_EXCEPTION_VECTORS, the SPL size
could not fit into the internal SRAM of some imx8m targets:
aarch64: + imx8mm_phg
+aarch64-linux-ld.bfd: u-boot-spl section `__u_boot_list' will not fit in region `.sram'
+aarch64-linux-ld.bfd: region `.sram' overflowed by 1824 bytes
Select LTO to prevent that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
All i.MX8M targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
When CONFIG_DWC_ETH_QOS_IMX=y and CONFIG_FEC_MXC is not selected, the
following warning is seen:
arch/arm/mach-imx/imx8m/clock_imx8mm.c: In function 'board_interface_eth_init':
arch/arm/mach-imx/imx8m/clock_imx8mm.c:914:24: warning: implicit declaration of function 'imx8mp_fec_interface_init; did you mean 'imx8mp_eqos_interface_init'? [-Wimplicit-function-declaration]
Fix it by adding a stub for imx8mp_fec_interface_init() to handle this
case.
This follows the same approach done on imx8mp_eqos_interface_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add Variscite manufacturer to the IMX8MN_VAR_SOM target menu label as
the majority of targets include the manufacturer as part of their menu
description/label and it helps when looking for a particular
manufacturer/board.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX8M by
reading out the ROM log events. This event is set by the BootROM if it
switched to the secondary copy due to primary copy being corrupted.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case of a secondary image boot from the user area of an eMMC device,
the correct offset must be calculated. The offset is fused in the fuse
IMG_CNTN_SET1_OFFSET of the i.MX8M Nano and Plus. The calculation of the
offset is described in the reference manual (IMX8MNRM Rev. 2, 07/2022
and IMX8MPRM Rev. 1, 06/2021):
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
* Secondary boot is disabled if fuse value is bigger than 10,
n = fuse value bigger than 10.
* n == 0: Offset = 4MB
* n == 2: Offset = 1MB
* Others & n <= 10 : Offset = 1MB*2^n
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out parsing of ROM log in function spl_mmc_emmc_boot_partition().
This can be helpful to detect a secondary image boot without fiddling
around with MMC partitions. This way for example, U-Boot is able to
detect a secondary image boot and can enter some fallback scenario like
starting a recovery mode.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
If optee is detected configure it in the Linux device-tree:
- add /firmware/optee node
- add /reserved-memory nodes for optee_core and optee_shm
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If dram_init_banksize() is called from SPL, the rom_pointer, at that
point, is not correctly initialized. This causes wrong calculation of
DRAM start and size in dram_init_banksize(). The issue became apparent
only in Falcon Mode. Added an extra condition to prevent using
rom_pointer in SPL.
Signed-off-by: Elena Popa <elena.popa@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Select DM_ETH_PHY so that the reset-gpios property of the ethphy node
can be used.
Also select DM_PCA953X, which is needed for resetting the
ethernet PHY on the carrier board via the PCA9534 I/O expander.
Commit 4e5114daf9eb ("imx8mn: synchronise device tree with linux") did
synchronise device tree with linux, which in effect removed obsolete
PHY reset properties and replaced them with new mdio DM
properties. But the commit didn't activate DM_ETH_PHY or DM_PCA953X.
Fixes: 4e5114daf9eb ("imx8mn: synchronise device tree with linux")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Getting
Found /vpu_g1@38300000 node
Modify /vpu_g1@38300000:status disabled
Found /vpu_g2@38310000 node
Modify /vpu_g2@38310000:status disabled
etc. on the console on every boot is needlessly verbose. Demote the
"Found ..." lines to debug(), which is consistent with other instances
in soc.c.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
