As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.
While we are at it, generalise the existing code by allowing a bitmap
of bits to clear and set, to cover newer SoCs: The A100 and H616 use a
different bit for the SIDDQ control.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Implement the .get_function operation, so the gpio command can report
the current function. Since the GPIOF_FUNC (versus GPIOF_UNUSED) mux
values vary among the PMICs, report all non-GPIO mux values as UNKNOWN.
Signed-off-by: Samuel Holland <samuel@sholland.org>
There are three major variants of the AXP PMIC GPIO functionality (plus
PMICs with no GPIOs at all). Except for GPIO3 on the AXP209, which uses
a different register layout, it is straightforward to support all three
variants with a single driver. Do this, and in the process remove the
GPIO-related definitions from the PMIC-specific headers, and therefore
the dependency on AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC driver implements the DM_PMIC uclass, those functions
can be used instead of the platform-specific "pmic_bus" functions.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it still depends on one of those
choices, and therefore also AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC has a DM driver and binds device tree subnodes, the
GPIO device can be bound that way, instead of from inside board code.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it does not differentiate among
the supported compatibles.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This is less confusing than half of the driver using "axp_gpio" and the
other half using "gpio_axp".
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, we can switch to DM_GPIO for these pins with no loss in
functionality. Since the driver now gets its pin configuration from
the device tree, we can remove the Kconfig symbols.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove
it, along with the rest of the support for AXP virtual GPIOs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that some regulator driver exists for this PMIC, add support for
probing regulator drivers from the device tree subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The first AXP regulator converted to use the regulator uclass is the
drivevbus switch, since it is used by the USB PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
In current slg7xl45106 gpio driver xlate() function we are not updating
gpio flags from DT. Read the given flag from DT and update the gpio desc
flags variable with required gpio direction state.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/a8d7b4799337bd99f61ace509889f02b192a9414.1648631275.git.michal.simek@xilinx.com
As we are not reading the PHY address in case of CONFIG_ETH_PHY in plat
function, phy address always prints as -1. So move the ethernet info
print statement to probe function, to display proper phy address.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f6efc6719d767b1bebe65987c22c6d52329f4225.1648631275.git.michal.simek@xilinx.com
If DM_ETH_PHY config is enabled PHY gpio reset is taken care by the
eth-phy-uclass driver, so use the PHY gpio reset functionality from
ethernet_id file when this config is disabled to reset the PHY.
Use debug() print instead of dev_err() to avoid warning incase if phy-id
compatible string is not present.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4d0fd3f9f886c1d943776025e5efb5438b0eb389.1648631275.git.michal.simek@xilinx.com
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below
ZynqMP> mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000
Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.
So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.
Fixes: a744a284e354 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Makes it possible to use 16-bit DDR memory.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:
* Introduce a memory region "ss" to allow dt to provide DDRSS region,
which is not the same as "ctl" which is the controller region.
* Introduce a "ti,ecc-enable" flag which allows a memorycontroller
instance to enable ecc.
* Introduce functionality to properly program the DDRSS registers to
enable ECC for the full DDR memory space if enabled with above flag.
* Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
account from DDR memory that must be reserved for ECC operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The current address being read from dt actually represents the ddrss_ctl
memory region, while ddrss_ss region is something else. Introduce
ddrss_ctl_regs and use it to free up ddrss_ss_regs for its proper
purpose later so that we can avoid confusion.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add functionality to enable, set priority to the input events and to
route to MCU ESM. On AM64x/AM62x devices, it is possible to route Main
ESM0 error events to MCU ESM. When these error events are routed to MCU
ESM high output, it can trigger the reset logic to reset the device,
when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'.
K3 based J7 devices (ex: J721e) also have ESM modules, and the changes
to the driver does not impact those devices.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
This also has the added benefit of picking the right clock/reset
bits for H6 and new SoCs that have a rearranged PRCM MMIO space.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Chips attached to the RSB bus require an initialization command before
they can be used. (Specifically, this command programs the chip's
runtime address.) The driver does this in its .probe_chip hook, under
the assumption that .probe_chip is called during child probe. This is
not the case; .probe_chip is only called by dm_i2c_probe, which is
intended for use by board-level code, not for chips with OF nodes.
Since this initialization command must be run before a child chip can be
used, do it before probing each child.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
