Chintan Vankar <c-vankar@ti.com> says:
This series enables Ethernet Boot on SK-AM62 device.
This series is based on commit 'f4f845b85926' of origin/next branch of
U-Boot.
Logs for Ethernet Boot for AM625-SK:
https://gist.github.com/chintanv133/464782796a9a60b9f5a49e674c5fc31a
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup TCHAN/RCHAN/RFLOW cfg registers.
Existing UDMA driver performed the above mentioned configuration
for UDMA. Add similar configuration for PKTDMA here.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Function "k3_ringacc_ring_reconfig_qmode_raw()" should reset qmode to
requested value and should not update other fields in ring configuration
register.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Expectation of k3_ringacc_ring_reset_raw() is to reset the ring to
requested size and not to 0. Fix this.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Initialize base address of ring config registers required to natively
setup ring cfg registers in the absence of Device Manager (DM) services
at R5 SPL stage. Since register property is defined as "ring" for PKTDMA
and "cfg" for UDMA, configure base address of ring configuration register
accordingly.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
RX_FL_CFG message should not be forwarded to TIFS and should be
handled within R5 SPL (when DM services are not available). Add
a no-op function to not handle RX_FL_CFG messages.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Use the API function list_count_nodes() to count the number of list
entries.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new ahab_derive command that derives the hardware unique key (HUK)
into a 16 or 32 bytes key and stores it at the given address.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Ye Li <ye.li@nxp.com>
Boot ROM on Meson needs some pages to be read/written in a special mode:
384 byte ECC mode (so called "short" by Amlogic) and with scrambling
enabled. Such pages are located on the chip in the following way (for
example):
[ p0 ][ p1 ][ p2 ][ p3 ][ p4 ][ p5 ][ p6 ][ p7 ] ... [ pN ]
^ ^ ^ ^
pX is page number "X". "^" means "special" page used by boot ROM - e.g.
every 2nd page in the range of [0, 7]. Step (2 here) and last page in
range is read from the device tree.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20240826131710.29746-4-avkrasnov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Based on Linux kernel:
commit f922bd798bb9 ("mtd: rawnand: add an option to specify NAND chip as a boot device")
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20240826131710.29746-2-avkrasnov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In the 7th generation of the SoC from Aspeed, the control logic of the
GPIO controller has been updated to support per-pin control. Each pin now
has its own 32-bit register, allowing for individual control of the pin’s
value, direction, interrupt type, and other settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Enabling CONFIG_DM_SEQ_ALIAS enables code which relies on
`trailing_strtol()` - which is only linked in SPL when CONFIG_SPL_STRTO
is enabled.
CONFIG_SPL_STRTO is not enabled by default - to ensure this function is
available in SPL, CONFIG_SPL_DM_SEQ_ALIAS should select
CONFIG_SPL_STRTO.
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jonas Karlman <jonas@kwiboo.se> says:
Use of fdt_parent_offset() is very expensive as detailed by the function
documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
This series remove multiple calls to fdt_parent_offset() or
ofnode_get_parent() when instead a single call can be made and the
returned value can be reused.
This series help reduce boot time by around:
- ~137ms on a Radxa ROCK Pi 4 (RK3399)
- ~33ms on a Radxa ZERO 3W (RK3566)
The counter value read from TDR register may not be correct.
Read SECCNT and CNTR25M instead to get the correct timestamp.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Until a live tree is used in U-Boot proper after relocation, use of
ofnode_get_parent() will trigger a call to the very expensive
fdt_parent_offset(), as detailed by the function documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Until a live tree is used in U-Boot proper after relocation, use of
ofnode_get_parent() will trigger a call to the very expensive
fdt_parent_offset() as detailed by the function documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use of fdt_parent_offset() is very expensive as detailed by the function
documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same nodeoffset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver.
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Currently uclass index is shown in DM tree dump which ignores alias
sequence numbering. The result could be confusing since these 2 numbers
could be different. Show device sequence number instead as it's more
meaningful.
Also update documentation to use sequence number.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the function is called with no NAND device attached, then this
function can return error value, proceeding further ignoring the same
can cause system crash. This is seen when "mtd list" is run with no NAND
addon cards connected.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
The sandbox pinmux driver is used in the non-test devicetree as well as
the test one. I didn't realize this when I modified the driver for
tests, and so broke the regular use case (which only resulted in
warnings). First, making the pinmux and the UART group available
pre-relocation to avoid ENODEV errors. Then, convert the pin groups and
functions to the new style, adding onewire group as well.
Fixes: 7f0f1806e3a ("test: pinmux: Add test for pin muxing")
Closes: https://source.denx.de/u-boot/u-boot/-/issues/2
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A system may have multiple SATA controller. Removing the controller with
the lowest sequence number before probing all SATA controllers makes no
sense.
In sata_rescan we remove all block devices which are children of SATA
controllers. We also have to remove the bootdev devices as they will be
created when scanning for block devices.
After probing all SATA controllers we must scan for block devices otherwise
we end up without any SATA block device.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for upstream linux split PCIe node.
Upstream linux have an alternative way to declare PCIe nodes that splits
them in dedicated nodes for each line instead of putting them all in one
node.
Detect this by checking if the mediatek,generic-pciecfg node is passed
as it's used to reference the common address for all the PCIe lines.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
uc_pdata->name is populated from device tree property "remoteproc-name".
For those devcices that don't set "remoteproc-name", uc_pdata->name
falls back to dev->name.
If two devices have same name, this will result into uc_pdata->name not
being unique and rproc_init() will fail.
Fix this by using combination of dev->name and dev->parent->name instead
of using just the dev->name to populate uc_pdata->name.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
This is handled by driver model so this driver should not be setting the
framebuffer address. Drop the assignment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a function to locate this information, rather than doing it
automatically on startup, to save space in global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function which returns the framebuffer address of the first
video device. This will allow the global_data field top be dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Only m68k and powerpc use this field, so move it to the arch-specific
info, to reduce the size for other archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having every caller set this up individually, create a
common init function. This allows new fields to be added without the
risk of them being left uninited.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Use the log subsystem instead of dev, to avoid including function names
in the code.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Update 'enhanced size' to use hex since this is the U-Boot default and
more natural for the large numbers involved.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The code makes quite a few uses of __func__ which puts the function
name into the resulting SPL image. Use the log subsystem instead, to
reduce size.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Use lower-case hex for the status output in sdhci_transfer_data(), to
match sdhci_send_command()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
In case CONFIG_USB_MUSB_HOST is set, the ux500_gadget_ops get overridden
to musb_usb_ops . Simply set the ops one way or the other depending on
whether CONFIG_USB_MUSB_HOST is set or not.
Fixes: ac4bf5d48a9e ("usb: gadget: ux500: Convert interrupt handling to usb_gadget_generic_ops")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240818200425.89045-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
u-boot-dfu-next-20240820
- Migrate Atmel usb gadget to DM_USB_GADGET
- More small cleanups/improvements on the atmel UDC driver
- Change udc uclass name from "usb" -> "usb_gadget"
Currently both USB host uclass and USB gadget uclass are using the same
name "usb" which break uclass functions like uclass_get_by_name().
Rename the uclass to "usb_gadget" to fix, also makes bind/unbind by class
index (or sequence) working.
This breaks the capacity of using "usb" as DT alias sequence numbering
which needs a fix afterwards.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/all/20240802092820.917450-1-admin@hifiphile.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Christian Marangi <ansuelsmth@gmail.com> says:
These are all the required patches to migrate clk and correctly support
OF_UPSTREAM. This will align the clk index to upstream to support the same
clk implementation with downstream and upstream DTS.
Add missing PERIBUS_SEL clock to match upstream linux clk ID order. Also
convert pericfg to mux + gate implementation as now we have also mux on
top of gates.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing clock PERI_UART4_PD for peri clock gates. This is needed to
match upstream linux clk ID in preparation for OF_UPSTREAM.
Also convert infracfg to mux + gate implementation as now we have mux on
top of gates.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing infra clock MUX1_SEL needed for CPU clock. This is needed to
match the upstream clk ID order in preparation for OF_UPSTREAM.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing clock for MAIN_CORE_EN. This is a special clock as it's a
gate for the APMIXED clocks required as a parent for CPU clocks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move INFRA_TRNG clock to the bottom of the clk ID to match upstream
linux order. This is in preparation of OF_UPSTREAM.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken peri_cgs clock with XTAL parents as they have wrong
definition of the parent type.
Correctly fix them and use CLK_PARENT_XTAL for them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi <ansuelsmth@gmail.com> says:
These are all the required patches to migrate clk and correctly support
OF_UPSTREAM. This will align the clk index to upstream to support the same
clk implementation with downstream and upstream DTS.
