At present the structs used by this driver are not accessible outside it,
so cannot be used with OF_PLATDATA_INST. Move them to a header file to
fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The T2080RDB has a ds1339 on i2c0. Add this to the devicetree and enable
the relevant support in the configs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Check CONFIG_SOCFPGA_SECURE_VAB_AUTH before perform 'is OS booted from FIT'
checking in board_prep_linux function. And, fix typo of
CONFIG_SOCFPGA_SECURE_VAB_AUTH_ALLOW_NON_FIT_IMAGE.
CONFIG_FIT will be enabled in both ATF and VAB boot flow, thus,
board_prep_linux function will always be called by both ATF and
VAB boot flow.
board_pre_linux function will do 'is OS booted from FIT' checking,
and it will be called before board_fit_image_post_process function.
VAB boot flow expects the OS is always booted from FIT and with VAB
signed cerfiticate because the VAB authentication is implemented in
board_fit_image_post_process function. So, VAB needs the 'is OS booted
from FIT' checking in board_pre_linux function.
However, for ATF boot flow, it is not a requirement that the OS must
always booted from FIT. The OS can be booted from individual Image and
kernel dtb file. Thus, we should not do 'if OS is booted from FIT'
checking in board_prep_linux function.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The startup code in arm/cpu/arm926ejs preserves the link register across
the call to lowlevel_init by using r4:
mov r4, lr /* perserve link reg across call */
bl lowlevel_init /* go setup pll,mux,memory */
mov lr, r4 /* restore link */
The lowlevel_init function for at91 machines based on the same CPU uses r4
and hence corrupts it causing a data abort when it returns to the startup
code. This patch fixes this by using r6 instead of r4 in the lowlevel_init
function.
Discovered and the fix was tested on a AT91SAM9261 based board.
Signed-off-by: Martin Townsend <martin@rufilla.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is not needed in normal operation. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some of these do not follow the rules. Make sure the driver name matches
the compatible string in all cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this property is a phandle but does not have a #xxx-cells
property to match it. Add one so that is works the same as gpio and clock
phandles.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently keyboard input fails in the GUI window opened by
./u-boot -T -l
Add the missing include to test.dts.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch makes use of the decompression mechanism implemented for mt7628
previously to reduce the total image size. Binman will be also removed.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The EPHY LEDs belongs to the built-in FE switch of MT7629, which is barely
used. These LED pins on reference boards are used as JTAG socket. So it's
a good idea to change the default state to JTAG, and this will make it
convenience for debugging.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Enable building SPL for EK874 board which is based on R8A774C0 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Renesas RZ/G2E (a.k.a. r8a774c0) is pin compatible with R-Car
E3 (a.k.a. r8a77990), however it doesn't have several automotive
specific peripherals.
This patch hooks R8A774C0 SoC with the pfc driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Enable by default SCP_03/CMD_SCP03 for sandbox target.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function can only locate the u-boot ELF file. For SPL it
is handy to be able to locate u-boot.img since this is what would normally
be loaded by SPL.
Add another argument to allow this to be selected.
While we are here, update the function to load SPL when running in TPL,
since that is the next stage.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present SPL only runs driver model tests. Update it to run all
available tests, i.e. in any test suite.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is the main test function for driver model but not for other tests.
Rename the file and the function so this is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix following compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS
are enabled :
arch/arm/mach-stm32mp/cpu.c: In function ‘early_enable_caches’:
arch/arm/mach-stm32mp/cpu.c:223:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_size’
223 | gd->arch.tlb_size = PGTABLE_SIZE;
| ^
arch/arm/mach-stm32mp/cpu.c:224:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_addr’
224 | gd->arch.tlb_addr = (unsigned long)&early_tlb;
| ^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Config option ARMADA_39X is never set so remove all dead code hidden under
ifdef CONFIG_ARMADA_39X blocks.
Also remove useless checks for CONFIG_ARMADA_38X define as this macro is
always defined for a38x code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable the clocks during bsec probe when they are present in device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The command "stm32prog serial <dev>" can directly use the device sequence
number of serial uclass as this sequence number is egual to alias when it
exist; this assumption simplify the code and avoid access to gd->fdt_blob
and the device tree parsing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When serial instance is not found in device tree, the console
should be enabled and the error should be indicated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_CMD_STM32PROG in a specific Kconfig file for stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Define in the RCC clock provider node which root clocks the driver
depends on. These are root oscillators, which may be present or
not, upon FDT content.
This update binding is introduced in Linux kernel device tree by patch
"ARM: dts: stm32: move clocks/resets to SCMI resources for stm32mp15"
This patch is a preliminary step for SCMI support of stm32mp15
boards with trusted boot chain, based on TF-A or OP-TEE.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
At present most of the Intel-specific code is built on all devices, even
those which don't have software support for the features provided there.
This means that any board can enable CONFIG_INTEL_ACPIGEN even if it does
not have the required features.
Add a new INTEL_SOC option to control this access. This must be selected
by SoCs that can support the required features.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed a typo in arch/x86/Kconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This option is better placed in the x86 code since it is not generic
enough to be in the core code. Move it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed a typo in arch/x86/Kconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When CONFIG_CHROMEOS is not enabled this currently does not build. Fix it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Building qemu-x86_64_defconfig with GCC 11.0 fails with:
arch/x86/cpu/intel_common/lpc.c:
In function ‘lpc_common_early_init’:
arch/x86/cpu/intel_common/lpc.c:56:40:
error: expression does not compute the number of elements in this array;
element type is ‘struct reg_info’, not ‘u32’ {aka ‘unsigned int’}
[-Werror=sizeof-array-div]
56 | sizeof(values) / sizeof(u32));
| ^
arch/x86/cpu/intel_common/lpc.c:56:40: note: add parentheses around the
second ‘sizeof’ to silence this warning
arch/x86/cpu/intel_common/lpc.c:50:11: note: array ‘values’ declared here
50 | } values[4], *ptr;
| ^~~~~~
Add parentheses to silence warning.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support 'vab' command to perform vendor authentication.
Command format: vab addr len
Authorize 'len' bytes starting at 'addr' via vendor public key
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Vendor Authorized Boot is a security feature for authenticating
the images such as U-Boot, ARM trusted Firmware, Linux kernel,
device tree blob and etc loaded from FIT. After those images are
loaded from FIT, the VAB certificate and signature block appended
at the end of each image are sent to Secure Device Manager (SDM)
for authentication. U-Boot will validate the SHA384 of the image
against the SHA384 hash stored in the VAB certificate before
sending the image to SDM for authentication.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.
List me as a co-maintainer for this board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_read_addr_size_index() returns fdt_addr_t which might be a
64-bit physical address. This might be true for some 85xx SoCs
whose CCSBAR is mapped beyond 4 GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Without this, the DM GPIO driver for MPC8xxx does not compile for
MPC85xx SoCs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In phys_to_virt() and virt_to_phys(), if CONFIG_ADDR_MAP is defined,
they use addrmap_ translation APIs to do the address translation.
However these APIs only work in post-relocation phase.
Update the code logic to fall back to use the default one when in
pre-relocation phase.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
