sunxi: Work around lack of Linux MBUS driver

Signed-off-by: Samuel Holland <samuel@sholland.org>

Kconfig

@@ -12,6 +12,8 @@ source "scripts/Kconfig.include"
 # Allow defaults in arch-specific code to override any given here
 source "arch/Kconfig"
 
+source "board/sunxi/Kconfig"
+
 menu "General setup"
 
 config BROKEN
@@ -252,7 +254,7 @@ config SYS_MALLOC_F_LEN
 	default 0x2000 if (ARCH_IMX8 || ARCH_IMX8M || ARCH_MX7 || \
 			   ARCH_MX7ULP || ARCH_MX6 || ARCH_MX5 || \
 			   ARCH_LS1012A || ARCH_LS1021A || ARCH_LS1043A || \
-			   ARCH_LS1046A || ARCH_QEMU || ARCH_SUNXI || ARCH_OWL)
+			   ARCH_LS1046A || ARCH_QEMU || ARCH_SUNXI || ARCH_OWL || TARGET_SUNXI)
 	default 0x400
 	help
 	  Before relocation, memory is very limited on many platforms. Still,
@@ -384,7 +386,7 @@ config BUILD_TARGET
 	default "u-boot-spl.kwb" if ARCH_MVEBU && SPL
 	default "u-boot-elf.srec" if RCAR_GEN3
 	default "u-boot.itb" if !BINMAN && SPL_LOAD_FIT && (ARCH_ROCKCHIP || \
-				ARCH_SUNXI || RISCV || ARCH_ZYNQMP)
+				RISCV || ARCH_ZYNQMP)
 	default "u-boot.kwb" if ARCH_KIRKWOOD
 	default "u-boot-with-spl.bin" if ARCH_AT91 && SPL_NAND_SUPPORT
 	default "u-boot-with-spl.imx" if ARCH_MX6 && SPL

Makefile

@@ -998,6 +998,23 @@ endif
 endif
 endif
 
+ifeq ($(CONFIG_MACH_SUN8I_H3)$(CONFIG_ARMV7_PSCI),yy)
+INPUTS-$(CONFIG_ARMV7_PSCI) += u-boot-resume.img
+
+MKIMAGEFLAGS_u-boot-resume.img := -B 0x400 -T sunxi_egon
+
+u-boot-resume.img: u-boot-resume.bin
+	$(call if_changed,mkimage)
+
+OBJCOPYFLAGS_u-boot-resume.bin := -O binary
+
+u-boot-resume.bin: u-boot-resume.o
+	$(call if_changed,objcopy)
+
+u-boot-resume.S: u-boot
+	@sed -En 's/(0x[[:xdigit:]]+) +psci_cpu_entry/ldr pc, =\1/p' $<.map > $@
+endif
+
 INPUTS-$(CONFIG_X86) += u-boot-x86-start16.bin u-boot-x86-reset16.bin \
 	$(if $(CONFIG_SPL_X86_16BIT_INIT),spl/u-boot-spl.bin) \
 	$(if $(CONFIG_TPL_X86_16BIT_INIT),tpl/u-boot-tpl.bin)

arch/arm/Kconfig

@@ -1151,13 +1151,17 @@ config ARCH_SUNXI
 	imply SPL_GPIO
 	imply SPL_LIBCOMMON_SUPPORT
 	imply SPL_LIBGENERIC_SUPPORT
+	imply SPL_LOAD_FIT
 	imply SPL_MMC if MMC
 	imply SPL_POWER
 	imply SPL_SERIAL
 	imply SYSRESET
 	imply SYSRESET_WATCHDOG
 	imply SYSRESET_WATCHDOG_AUTO
+	imply USB_EHCI_GENERIC
+	imply USB_ETHER if USB_MUSB_GADGET
 	imply USB_GADGET
+	imply USB_OHCI_GENERIC
 	imply WDT
 
 config ARCH_U8500

arch/arm/cpu/armv7/Kconfig

@@ -75,11 +75,14 @@ config ARMV7_PSCI
 choice
 	prompt "Supported PSCI version"
 	depends on ARMV7_PSCI
-	default ARMV7_PSCI_0_1 if ARCH_SUNXI
+	default ARMV7_PSCI_1_1 if ARCH_SUNXI
 	default ARMV7_PSCI_1_0
 	help
 	  Select the supported PSCI version.
 
+config ARMV7_PSCI_1_1
+	bool "PSCI V1.1"
+
 config ARMV7_PSCI_1_0
 	bool "PSCI V1.0"
 

arch/arm/cpu/armv7/sunxi/Makefile

@@ -13,8 +13,12 @@ obj-$(CONFIG_MACH_SUN6I)	+= sram.o
 obj-$(CONFIG_MACH_SUN8I)	+= sram.o
 
 ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_MACH_SUN8I_H3
+obj-$(CONFIG_ARMV7_PSCI)	+= psci-scpi.o
+else
 obj-$(CONFIG_ARMV7_PSCI)	+= psci.o
 endif
+endif
 
 ifdef CONFIG_SPL_BUILD
 obj-y	+= fel_utils.o

arch/arm/cpu/armv7/sunxi/psci-scpi.c

@@ -0,0 +1,451 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2018-2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/cpucfg.h>
+#include <asm/armv7.h>
+#include <asm/gic.h>
+#include <asm/io.h>
+#include <asm/psci.h>
+#include <asm/secure.h>
+#include <asm/system.h>
+
+#define	GICD_BASE		(SUNXI_GIC400_BASE + GIC_DIST_OFFSET)
+#define	GICC_BASE		(SUNXI_GIC400_BASE + GIC_CPU_OFFSET_A15)
+
+#define HW_ON			0
+#define HW_OFF			1
+#define HW_STANDBY		2
+
+#define MPIDR_AFFLVL0(mpidr)	(mpidr & 0xf)
+#define MPIDR_AFFLVL1(mpidr)	(mpidr >> 8 & 0xf)
+
+#define SCPI_SHMEM_BASE		0x0004be00
+#define SCPI_SHMEM		((struct scpi_shmem *)SCPI_SHMEM_BASE)
+
+#define SCPI_RX_CHANNEL		1
+#define SCPI_TX_CHANNEL		0
+#define SCPI_VIRTUAL_CHANNEL	BIT(0)
+
+#define SCPI_MESSAGE_SIZE	0x100
+#define SCPI_PAYLOAD_SIZE	(SCPI_MESSAGE_SIZE - sizeof(struct scpi_header))
+
+#define SUNXI_MSGBOX_BASE	0x01c17000
+#define REMOTE_IRQ_STAT_REG	(SUNXI_MSGBOX_BASE + 0x0050)
+#define LOCAL_IRQ_STAT_REG	(SUNXI_MSGBOX_BASE + 0x0070)
+#define MSG_STAT_REG(n)		(SUNXI_MSGBOX_BASE + 0x0140 + 0x4 * (n))
+#define MSG_DATA_REG(n)		(SUNXI_MSGBOX_BASE + 0x0180 + 0x4 * (n))
+
+#define RX_IRQ(n)		BIT(0 + 2 * (n))
+#define TX_IRQ(n)		BIT(1 + 2 * (n))
+
+enum {
+	CORE_POWER_LEVEL		= 0,
+	CLUSTER_POWER_LEVEL		= 1,
+	CSS_POWER_LEVEL			= 2,
+};
+
+enum {
+	SCPI_CMD_SCP_READY		= 0x01,
+	SCPI_CMD_SET_CSS_POWER_STATE	= 0x03,
+	SCPI_CMD_GET_CSS_POWER_STATE	= 0x04,
+	SCPI_CMD_SET_SYS_POWER_STATE	= 0x05,
+};
+
+enum {
+	SCPI_E_OK			= 0,
+	SCPI_E_PARAM			= 1,
+	SCPI_E_ALIGN			= 2,
+	SCPI_E_SIZE			= 3,
+	SCPI_E_HANDLER			= 4,
+	SCPI_E_ACCESS			= 5,
+	SCPI_E_RANGE			= 6,
+	SCPI_E_TIMEOUT			= 7,
+	SCPI_E_NOMEM			= 8,
+	SCPI_E_PWRSTATE			= 9,
+	SCPI_E_SUPPORT			= 10,
+	SCPI_E_DEVICE			= 11,
+	SCPI_E_BUSY			= 12,
+	SCPI_E_OS			= 13,
+	SCPI_E_DATA			= 14,
+	SCPI_E_STATE			= 15,
+};
+
+enum {
+	SCPI_POWER_ON			= 0x00,
+	SCPI_POWER_RETENTION		= 0x01,
+	SCPI_POWER_OFF			= 0x03,
+};
+
+enum {
+	SCPI_SYSTEM_SHUTDOWN		= 0x00,
+	SCPI_SYSTEM_REBOOT		= 0x01,
+	SCPI_SYSTEM_RESET		= 0x02,
+};
+
+struct scpi_header {
+	u8			command;
+	u8			sender;
+	u16			size;
+	u32			status;
+};
+
+struct scpi_message {
+	struct scpi_header	header;
+	u8			payload[SCPI_PAYLOAD_SIZE];
+};
+
+struct scpi_shmem {
+	struct scpi_message	rx;
+	struct scpi_message	tx;
+};
+
+static bool __secure_data gic_dist_init;
+
+static u32 __secure_data lock;
+
+static inline u32 __secure read_mpidr(void)
+{
+	u32 val;
+
+	asm volatile ("mrc p15, 0, %0, c0, c0, 5" : "=r" (val));
+
+	return val;
+}
+
+static void __secure scpi_begin_command(void)
+{
+	u32 mpidr = read_mpidr();
+
+	do {
+		while (readl(&lock));
+		writel(mpidr, &lock);
+		dsb();
+	} while (readl(&lock) != mpidr);
+	while (readl(REMOTE_IRQ_STAT_REG) & RX_IRQ(SCPI_TX_CHANNEL));
+}
+
+static void __secure scpi_send_command(void)
+{
+	writel(SCPI_VIRTUAL_CHANNEL, MSG_DATA_REG(SCPI_TX_CHANNEL));
+}
+
+static void __secure scpi_wait_response(void)
+{
+	while (!readl(MSG_STAT_REG(SCPI_RX_CHANNEL)));
+}
+
+static void __secure scpi_end_command(void)
+{
+	while (readl(MSG_STAT_REG(SCPI_RX_CHANNEL)))
+		readl(MSG_DATA_REG(SCPI_RX_CHANNEL));
+	writel(RX_IRQ(SCPI_RX_CHANNEL), LOCAL_IRQ_STAT_REG);
+	writel(0, &lock);
+}
+
+static void __secure scpi_set_css_power_state(u32 target_cpu, u32 core_state,
+					      u32 cluster_state, u32 css_state)
+{
+	struct scpi_shmem *shmem = SCPI_SHMEM;
+
+	scpi_begin_command();
+
+	shmem->tx.header.command = SCPI_CMD_SET_CSS_POWER_STATE;
+	shmem->tx.header.size = 4;
+
+	shmem->tx.payload[0] = target_cpu    >> 4 | target_cpu;
+	shmem->tx.payload[1] = cluster_state << 4 | core_state;
+	shmem->tx.payload[2] = css_state;
+	shmem->tx.payload[3] = 0;
+
+	scpi_send_command();
+	scpi_end_command();
+}
+
+static s32 __secure scpi_get_css_power_state(u32 target_cpu, u8 *core_states,
+					     u8 *cluster_state)
+{
+	struct scpi_shmem *shmem = SCPI_SHMEM;
+	u32 cluster = MPIDR_AFFLVL1(target_cpu);
+	u32 offset;
+	s32 ret;
+
+	scpi_begin_command();
+
+	shmem->tx.header.command = SCPI_CMD_GET_CSS_POWER_STATE;
+	shmem->tx.header.size = 0;
+
+	scpi_send_command();
+	scpi_wait_response();
+
+	for (offset = 0; offset < shmem->rx.header.size; offset += 2) {
+		if ((shmem->rx.payload[offset] & 0xf) == cluster) {
+			*cluster_state = shmem->rx.payload[offset+0] >> 4;
+			*core_states   = shmem->rx.payload[offset+1];
+
+			break;
+		}
+	}
+
+	ret = shmem->rx.header.status;
+
+	scpi_end_command();
+
+	return ret;
+}
+
+static s32 __secure scpi_set_sys_power_state(u32 sys_state)
+{
+	struct scpi_shmem *shmem = SCPI_SHMEM;
+	s32 ret;
+
+	scpi_begin_command();
+
+	shmem->tx.header.command = SCPI_CMD_SET_SYS_POWER_STATE;
+	shmem->tx.header.size = 1;
+
+	shmem->tx.payload[0] = sys_state;
+
+	scpi_send_command();
+	scpi_wait_response();
+
+	ret = shmem->rx.header.status;
+
+	scpi_end_command();
+
+	return ret;
+}
+
+void psci_enable_smp(void);
+
+static s32 __secure psci_suspend_common(u32 pc, u32 context_id, u32 core_state,
+					u32 cluster_state, u32 css_state)
+
+{
+	u32 target_cpu = read_mpidr();
+
+	if (core_state == SCPI_POWER_OFF)
+		psci_save(MPIDR_AFFLVL0(target_cpu), pc, context_id);
+	if (css_state == SCPI_POWER_OFF)
+		gic_dist_init = true;
+
+	scpi_set_css_power_state(target_cpu, core_state,
+				 cluster_state, css_state);
+
+	psci_cpu_off_common();
+
+	wfi();
+
+	psci_enable_smp();
+
+	return ARM_PSCI_RET_SUCCESS;
+}
+
+u32 __secure psci_version(void)
+{
+	return ARM_PSCI_VER_1_1;
+}
+
+s32 __secure psci_cpu_suspend(u32 __always_unused function_id,
+			      u32 power_state, u32 pc, u32 context_id)
+{
+	return psci_suspend_common(pc, context_id,
+				   power_state >> 0 & 0xf,
+				   power_state >> 4 & 0xf,
+				   power_state >> 8 & 0xf);
+}
+
+s32 __secure psci_cpu_off(void)
+{
+	u32 pc = 0, context_id = 0;
+
+	return psci_suspend_common(pc, context_id, SCPI_POWER_OFF,
+				   SCPI_POWER_OFF, SCPI_POWER_ON);
+}
+
+s32 __secure psci_cpu_on(u32 __always_unused function_id,
+			 u32 target_cpu, u32 pc, u32 context_id)
+{
+	psci_save(MPIDR_AFFLVL0(target_cpu), pc, context_id);
+
+	scpi_set_css_power_state(target_cpu, SCPI_POWER_ON,
+				 SCPI_POWER_ON, SCPI_POWER_ON);
+
+	return ARM_PSCI_RET_SUCCESS;
+}
+
+s32 __secure psci_affinity_info(u32 function_id,
+				u32 target_cpu, u32 power_level)
+{
+	if (power_level != CORE_POWER_LEVEL)
+		return ARM_PSCI_RET_INVAL;
+
+	/* This happens to have the same HW_ON/HW_OFF encoding. */
+	return psci_node_hw_state(function_id, target_cpu, power_level);
+}
+
+void __secure psci_system_off(void)
+{
+	scpi_set_sys_power_state(SCPI_SYSTEM_SHUTDOWN);
+
+	/* Wait to be turned off. */
+	for (;;) wfi();
+}
+
+void __secure psci_system_reset(void)
+{
+	scpi_set_sys_power_state(SCPI_SYSTEM_REBOOT);
+
+	/* Wait to be turned off. */
+	for (;;) wfi();
+}
+
+s32 __secure psci_features(u32 __always_unused function_id,
+			   u32 psci_fid)
+{
+	switch (psci_fid) {
+	case ARM_PSCI_0_2_FN_PSCI_VERSION:
+	case ARM_PSCI_0_2_FN_CPU_SUSPEND:
+	case ARM_PSCI_0_2_FN_CPU_OFF:
+	case ARM_PSCI_0_2_FN_CPU_ON:
+	case ARM_PSCI_0_2_FN_AFFINITY_INFO:
+	case ARM_PSCI_0_2_FN_SYSTEM_OFF:
+	case ARM_PSCI_0_2_FN_SYSTEM_RESET:
+	case ARM_PSCI_1_0_FN_PSCI_FEATURES:
+	case ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND:
+	case ARM_PSCI_1_0_FN_NODE_HW_STATE:
+	case ARM_PSCI_1_0_FN_SYSTEM_SUSPEND:
+	case ARM_PSCI_1_1_FN_SYSTEM_RESET2:
+		return ARM_PSCI_RET_SUCCESS;
+	default:
+		return ARM_PSCI_RET_NI;
+	}
+}
+
+s32 __secure psci_cpu_default_suspend(u32 __always_unused function_id,
+				      u32 pc, u32 context_id)
+{
+	return psci_suspend_common(pc, context_id, SCPI_POWER_OFF,
+				   SCPI_POWER_OFF, SCPI_POWER_RETENTION);
+}
+
+s32 __secure psci_node_hw_state(u32 __always_unused function_id,
+				u32 target_cpu, u32 power_level)
+{
+	u32 core = MPIDR_AFFLVL0(target_cpu);
+	u8 core_states, cluster_state;
+
+	if (power_level >= CSS_POWER_LEVEL)
+		return HW_ON;
+	if (scpi_get_css_power_state(target_cpu, &core_states, &cluster_state))
+		return ARM_PSCI_RET_NI;
+	if (power_level == CLUSTER_POWER_LEVEL) {
+		if (cluster_state == SCPI_POWER_ON)
+			return HW_ON;
+		if (cluster_state < SCPI_POWER_OFF)
+			return HW_STANDBY;
+		return HW_OFF;
+	}
+
+	return (core_states & BIT(core)) ? HW_ON : HW_OFF;
+}
+
+s32 __secure psci_system_suspend(u32 __always_unused function_id,
+				 u32 pc, u32 context_id)
+{
+	return psci_suspend_common(pc, context_id, SCPI_POWER_OFF,
+				   SCPI_POWER_OFF, SCPI_POWER_OFF);
+}
+
+s32 __secure psci_system_reset2(u32 __always_unused function_id,
+				u32 reset_type, u32 cookie)
+{
+	s32 ret;
+
+	if (reset_type)
+		return ARM_PSCI_RET_INVAL;
+
+	ret = scpi_set_sys_power_state(SCPI_SYSTEM_RESET);
+	if (ret)
+		return ARM_PSCI_RET_INVAL;
+
+	/* Wait to be turned off. */
+	for (;;) wfi();
+}
+
+/*
+ * R40 is different from other single cluster SoCs. The secondary core
+ * entry address register is in the SRAM controller address range.
+ */
+#define SUN8I_R40_SRAMC_SOFT_ENTRY_REG0		(0xbc)
+
+#ifdef CONFIG_MACH_SUN8I_R40
+/* secondary core entry address is programmed differently on R40 */
+static void __secure sunxi_set_entry_address(void *entry)
+{
+	writel((u32)entry,
+	       SUNXI_SRAMC_BASE + SUN8I_R40_SRAMC_SOFT_ENTRY_REG0);
+}
+#else
+static void __secure sunxi_set_entry_address(void *entry)
+{
+	struct sunxi_cpucfg_reg *cpucfg =
+		(struct sunxi_cpucfg_reg *)SUNXI_CPUCFG_BASE;
+
+	writel((u32)entry, &cpucfg->priv0);
+
+	if (IS_ENABLED(CONFIG_MACH_SUN8I_H3)) {
+		/* Redirect CPU 0 to the secure monitor via the resume shim. */
+		writel(0x16aaefe8, &cpucfg->super_standy_flag);
+		writel(0xaa16efe8, &cpucfg->super_standy_flag);
+		writel(SUNXI_RESUME_BASE, &cpucfg->priv1);
+	}
+}
+#endif
+
+void __secure psci_arch_init(void)
+{
+	static bool __secure_data one_time_init = true;
+
+	if (one_time_init) {
+		/* Set secondary core power-on PC. */
+		sunxi_set_entry_address(psci_cpu_entry);
+
+		/* Wait for the SCP firmware to boot. */
+		scpi_begin_command();
+		scpi_wait_response();
+		scpi_end_command();
+
+		one_time_init = false;
+	}
+
+	/*
+	 * Copied from arch/arm/cpu/armv7/virt-v7.c
+	 * See also gic_resume() in arch/arm/mach-imx/mx7/psci-mx7.c
+	 */
+	if (gic_dist_init) {
+		u32 i, itlinesnr;
+
+		/* enable the GIC distributor */
+		writel(readl(GICD_BASE + GICD_CTLR) | 0x03, GICD_BASE + GICD_CTLR);
+
+		/* TYPER[4:0] contains an encoded number of available interrupts */
+		itlinesnr = readl(GICD_BASE + GICD_TYPER) & 0x1f;
+
+		/* set all bits in the GIC group registers to one to allow access
+		 * from non-secure state. The first 32 interrupts are private per
+		 * CPU and will be set later when enabling the GIC for each core
+		 */
+		for (i = 1; i <= itlinesnr; i++)
+			writel((unsigned)-1, GICD_BASE + GICD_IGROUPRn + 4 * i);
+
+		gic_dist_init = false;
+	}
+
+	/* Be cool with non-secure. */
+	writel(0xff, GICC_BASE + GICC_PMR);
+}

arch/arm/cpu/armv7/sunxi/psci.c

@@ -10,6 +10,7 @@
 #include <common.h>
 #include <asm/cache.h>
 
+#include <asm/arch/clock.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/cpucfg.h>
 #include <asm/arch/prcm.h>
@@ -38,6 +39,15 @@
 #define SUN8I_R40_PWR_CLAMP(cpu)		(0x120 + (cpu) * 0x4)
 #define SUN8I_R40_SRAMC_SOFT_ENTRY_REG0		(0xbc)
 
+static inline u32 __secure cp15_read_mpidr(void)
+{
+	u32 val;
+
+	asm volatile ("mrc p15, 0, %0, c0, c0, 5" : "=r" (val));
+
+	return val;
+}
+
 static void __secure cp15_write_cntp_tval(u32 tval)
 {
 	asm volatile ("mcr p15, 0, %0, c14, c2, 0" : : "r" (tval));
@@ -132,6 +142,13 @@ static void __secure sunxi_set_entry_address(void *entry)
 		(struct sunxi_cpucfg_reg *)SUNXI_CPUCFG_BASE;
 
 	writel((u32)entry, &cpucfg->priv0);
+
+#ifdef CONFIG_MACH_SUN8I_H3
+	/* Redirect CPU 0 to the secure monitor via the resume shim. */
+	writel(0x16aaefe8, &cpucfg->super_standy_flag);
+	writel(0xaa16efe8, &cpucfg->super_standy_flag);
+	writel(SUNXI_RESUME_BASE, &cpucfg->priv1);
+#endif
 }
 #endif
 
@@ -246,9 +263,12 @@ out:
 int __secure psci_cpu_on(u32 __always_unused unused, u32 mpidr, u32 pc,
 			 u32 context_id)
 {
+	struct sunxi_ccm_reg *ccu = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
 	struct sunxi_cpucfg_reg *cpucfg =
 		(struct sunxi_cpucfg_reg *)SUNXI_CPUCFG_BASE;
 	u32 cpu = (mpidr & 0x3);
+	u32 cpu_clk;
+	u32 bus_clk;
 
 	/* store target PC and context id */
 	psci_save(cpu, pc, context_id);
@@ -265,12 +285,32 @@ int __secure psci_cpu_on(u32 __always_unused unused, u32 mpidr, u32 pc,
 	/* Lock CPU (Disable external debug access) */
 	clrbits_le32(&cpucfg->dbg_ctrl1, BIT(cpu));
 
+	if (IS_ENABLED(CONFIG_MACH_SUN8I_H3) && cpu == 0) {
+		/* Save registers that will be clobbered by the BROM. */
+		cpu_clk = readl(&ccu->cpu_axi_cfg);
+		bus_clk = readl(&ccu->ahb1_apb1_div);
+
+		/* Bypass PLL_PERIPH0 so AHB1 frequency does not spike. */
+		setbits_le32(&ccu->pll6_cfg, BIT(25));
+	}
+
 	/* Power up target CPU */
 	sunxi_cpu_set_power(cpu, true);
 
 	/* De-assert reset on target CPU */
 	writel(BIT(1) | BIT(0), &cpucfg->cpu[cpu].rst);
 
+	if (IS_ENABLED(CONFIG_MACH_SUN8I_H3) && cpu == 0) {
+		/* Spin until the BROM has clobbered the clock registers. */
+		while (readl(&ccu->ahb1_apb1_div) != 0x00001100);
+
+		/* Restore the registers and turn off PLL_PERIPH0 bypass. */
+		writel(cpu_clk, &ccu->cpu_axi_cfg);
+		writel(bus_clk, &ccu->ahb1_apb1_div);
+
+		clrbits_le32(&ccu->pll6_cfg, BIT(25));
+	}
+
 	/* Unlock CPU (Disable external debug access) */
 	setbits_le32(&cpucfg->dbg_ctrl1, BIT(cpu));
 
@@ -281,9 +321,14 @@ s32 __secure psci_cpu_off(void)
 {
 	psci_cpu_off_common();
 
+	if (cp15_read_mpidr() & 3) {
 		/* Ask CPU0 via SGI15 to pull the rug... */
 		writel(BIT(16) | 15, GICD_BASE + GICD_SGIR);
 		dsb();
+	} else {
+		/* Unmask FIQs to service SGI15. */
+		asm volatile ("cpsie f");
+	}
 
 	/* Wait to be turned off */
 	while (1)

arch/arm/cpu/armv8/fwcall.c

@@ -103,7 +103,7 @@ void __noreturn psci_system_reset2(u32 reset_level, u32 cookie)
 {
 	struct pt_regs regs;
 
-	regs.regs[0] = ARM_PSCI_0_2_FN64_SYSTEM_RESET2;
+	regs.regs[0] = ARM_PSCI_1_1_FN64_SYSTEM_RESET2;
 	regs.regs[1] = PSCI_RESET2_TYPE_VENDOR | reset_level;
 	regs.regs[2] = cookie;
 	if (use_smc_for_psci)

arch/arm/dts/Makefile

@@ -531,7 +531,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-olinuxino-lime.dtb \
 	sun4i-a10-pcduino.dtb \
 	sun4i-a10-pcduino2.dtb \
-	sun4i-a10-pov-protab2-ips9.dtb
+	sun4i-a10-pov-protab2-ips9.dtb \
+	sun4i-a10-topwise-a721.dtb
 dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a10s-auxtek-t003.dtb \
 	sun5i-a10s-auxtek-t004.dtb \
@@ -546,11 +547,14 @@ dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a13-hsg-h702.dtb \
 	sun5i-a13-inet-86vs.dtb \
 	sun5i-a13-inet-98v-rev2.dtb \
+	sun5i-a13-licheepi-one.dtb \
 	sun5i-a13-olinuxino.dtb \
 	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-pocketbook-touch-lux-3.dtb \
 	sun5i-a13-q8-tablet.dtb \
 	sun5i-a13-utoo-p66.dtb \
 	sun5i-gr8-chip-pro.dtb \
+	sun5i-gr8-evb.dtb \
 	sun5i-r8-chip.dtb
 dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-app4-evb1.dtb \
@@ -574,11 +578,13 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-bananapro.dtb \
 	sun7i-a20-cubieboard2.dtb \
 	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-i12-tvbox.dtb \
 	sun7i-a20-icnova-swac.dtb \
 	sun7i-a20-itead-ibox.dtb \
 	sun7i-a20-lamobo-r1.dtb \
+	sun7i-a20-linutronix-testbox-v2.dtb \
 	sun7i-a20-m3.dtb \
 	sun7i-a20-m5.dtb \
 	sun7i-a20-mk808c.dtb \
@@ -586,6 +592,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-olimex-som204-evb.dtb \
 	sun7i-a20-olimex-som204-evb-emmc.dtb \
 	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime-emmc.dtb \
 	sun7i-a20-olinuxino-lime2.dtb \
 	sun7i-a20-olinuxino-lime2-emmc.dtb \
 	sun7i-a20-olinuxino-micro.dtb \
@@ -602,17 +609,22 @@ dtb-$(CONFIG_MACH_SUN8I_A23) += \
 	sun8i-a23-evb.dtb \
 	sun8i-a23-gt90h-v4.dtb \
 	sun8i-a23-inet86dz.dtb \
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-a23-ippo-q8h-v5.dtb \
 	sun8i-a23-polaroid-mid2407pxe03.dtb \
 	sun8i-a23-polaroid-mid2809pxe04.dtb \
 	sun8i-a23-q8-tablet.dtb
 dtb-$(CONFIG_MACH_SUN8I_A33) += \
+	sun8i-a33-et-q8-v1.6.dtb \
 	sun8i-a33-ga10h-v1.1.dtb \
 	sun8i-a33-inet-d978-rev2.dtb \
+	sun8i-a33-ippo-q8h-v1.2.dtb \
 	sun8i-a33-olinuxino.dtb \
 	sun8i-a33-q8-tablet.dtb \
 	sun8i-a33-sinlinx-sina33.dtb \
 	sun8i-r16-bananapi-m2m.dtb \
-	sun8i-r16-nintendo-nes-classic-edition.dtb \
+	sun8i-r16-nintendo-nes-classic.dtb \
+	sun8i-r16-nintendo-super-nes-classic.dtb \
 	sun8i-r16-parrot.dtb
 dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
@@ -635,6 +647,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \
 	sun8i-h3-nanopi-neo-air.dtb \
+	sun8i-h3-nanopi-r1.dtb \
 	sun8i-h3-orangepi-2.dtb \
 	sun8i-h3-orangepi-lite.dtb \
 	sun8i-h3-orangepi-one.dtb \
@@ -647,9 +660,13 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-zeropi.dtb
 dtb-$(CONFIG_MACH_SUN8I_R40) += \
 	sun8i-r40-bananapi-m2-ultra.dtb \
+	sun8i-r40-oka40i-c.dtb \
+	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
 dtb-$(CONFIG_MACH_SUN8I_V3S) += \
+	sun8i-s3-elimo-initium.dtb \
 	sun8i-s3-pinecube.dtb \
+	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-licheepi-zero.dtb
 dtb-$(CONFIG_MACH_SUN50I_H5) += \
 	sun50i-h5-bananapi-m2-plus.dtb \
@@ -670,7 +687,9 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \
 	sun50i-h6-orangepi-lite2.dtb \
 	sun50i-h6-orangepi-one-plus.dtb \
 	sun50i-h6-pine-h64.dtb \
-	sun50i-h6-tanix-tx6.dtb
+	sun50i-h6-pine-h64-model-b.dtb \
+	sun50i-h6-tanix-tx6.dtb \
+	sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_MACH_SUN50I_H616) += \
 	sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_MACH_SUN50I) += \

arch/arm/dts/axp209.dtsi

@@ -53,7 +53,7 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp202-ac-power-supply";
 		status = "disabled";
 	};
@@ -69,7 +69,7 @@
 		#gpio-cells = <2>;
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp209-battery-power-supply";
 		status = "disabled";
 	};
@@ -112,7 +112,7 @@
 		};
 	};
 
-	usb_power_supply: usb-power-supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp202-usb-power-supply";
 		status = "disabled";
 	};

arch/arm/dts/axp22x.dtsi

@@ -52,16 +52,27 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp221-ac-power-supply";
 		status = "disabled";
 	};
 
-	battery_power_supply: battery-power-supply {
+	axp_adc: adc {
+		compatible = "x-powers,axp221-adc";
+		#io-channel-cells = <1>;
+	};
+
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp221-battery-power-supply";
 		status = "disabled";
 	};
 
+	axp_gpio: gpio {
+		compatible = "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	regulators {
 		/* Default work frequency for buck regulators */
 		x-powers,dcdc-freq = <3000>;
@@ -158,7 +169,7 @@
 		};
 	};
 
-	usb_power_supply: usb_power_supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp221-usb-power-supply";
 		status = "disabled";
 	};

arch/arm/dts/axp803.dtsi

@@ -10,7 +10,7 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp803-ac-power-supply",
 			     "x-powers,axp813-ac-power-supply";
 		status = "disabled";
@@ -26,18 +26,18 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		gpio0_ldo: gpio0-ldo {
+		gpio0_ldo: gpio0-ldo-pin {
 			pins = "GPIO0";
 			function = "ldo";
 		};
 
-		gpio1_ldo: gpio1-ldo {
+		gpio1_ldo: gpio1-ldo-pin {
 			pins = "GPIO1";
 			function = "ldo";
 		};
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp803-battery-power-supply",
 			     "x-powers,axp813-battery-power-supply";
 		status = "disabled";
@@ -147,7 +147,7 @@
 		};
 	};
 
-	usb_power_supply: usb-power-supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp803-usb-power-supply",
 			     "x-powers,axp813-usb-power-supply";
 		status = "disabled";

arch/arm/dts/axp809.dtsi

@@ -50,4 +50,11 @@
 	compatible = "x-powers,axp809";
 	interrupt-controller;
 	#interrupt-cells = <1>;
+
+	axp_gpio: gpio {
+		compatible = "x-powers,axp809-gpio",
+			     "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

arch/arm/dts/axp81x.dtsi

@@ -48,6 +48,11 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
+	ac_power_supply: ac-power {
+		compatible = "x-powers,axp813-ac-power-supply";
+		status = "disabled";
+	};
+
 	axp_adc: adc {
 		compatible = "x-powers,axp813-adc";
 		#io-channel-cells = <1>;
@@ -58,18 +63,18 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		gpio0_ldo: gpio0-ldo {
+		gpio0_ldo: gpio0-ldo-pin {
 			pins = "GPIO0";
 			function = "ldo";
 		};
 
-		gpio1_ldo: gpio1-ldo {
+		gpio1_ldo: gpio1-ldo-pin {
 			pins = "GPIO1";
 			function = "ldo";
 		};
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp813-battery-power-supply";
 		status = "disabled";
 	};
@@ -166,4 +171,8 @@
 			status = "disabled";
 		};
 	};
+
+	usb_power_supply: usb-power {
+		compatible = "x-powers,axp813-usb-power-supply";
+	};
 };

arch/arm/dts/sun4i-a10-a1000.dts

@@ -60,15 +60,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-0 {
 			label = "a1000:red:usr";
 			gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-1 {
 			label = "a1000:blue:pwr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -125,7 +136,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -133,6 +144,20 @@
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 

arch/arm/dts/sun4i-a10-ba10-tvbox.dts

@@ -68,7 +68,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 

arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts

@@ -131,20 +131,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &reg_usb0_vbus {
 	status = "okay";
 };
@@ -165,10 +151,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-cubieboard.dts

@@ -75,12 +75,12 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_cubieboard>;
 
-		blue {
+		led-0 {
 			label = "cubieboard:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */
 		};
 
-		green {
+		led-1 {
 			label = "cubieboard:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* LED2 */
 			linux,default-trigger = "heartbeat";
@@ -114,7 +114,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -184,12 +184,6 @@
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
 };
 
 &reg_ahci_5v {
@@ -254,9 +248,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts

@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
@@ -158,20 +159,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_pin>;
@@ -223,10 +210,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-hackberry.dts

@@ -80,7 +80,7 @@
 };
 
 &emac {
-	phy = <&phy0>;
+	phy-handle = <&phy0>;
 	status = "okay";
 };
 

arch/arm/dts/sun4i-a10-hyundai-a7hd.dts

@@ -86,20 +86,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &reg_usb0_vbus {
 	status = "okay";
 };
@@ -121,10 +107,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-inet1.dts

@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
@@ -164,20 +165,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_pin>;
@@ -233,10 +220,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;

arch/arm/dts/sun4i-a10-inet97fv2.dts

@@ -1,7 +1,7 @@
 /*
  * Copyright 2014 Open Source Support GmbH
  *
- * David Lanzendörfer <david.lanzendoerfer@o2s.ch>
+ * David Lanzendörfer <david.lanzendoerfer@o2s.ch>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -150,20 +150,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
@@ -209,10 +195,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-inet9f-rev03.dts

@@ -61,10 +61,6 @@
 
 	gpio-keys {
 		compatible = "gpio-keys-polled";
-		pinctrl-names = "default";
-		pinctrl-0 = <&key_pins_inet9f>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <20>;
 
 		left-joystick-left {
@@ -72,7 +68,7 @@
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+			gpios = <&pio 0 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA6 */
 		};
 
 		left-joystick-right {
@@ -80,7 +76,7 @@
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+			gpios = <&pio 0 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA5 */
 		};
 
 		left-joystick-up {
@@ -88,7 +84,7 @@
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+			gpios = <&pio 0 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA8 */
 		};
 
 		left-joystick-down {
@@ -96,7 +92,7 @@
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+			gpios = <&pio 0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA9 */
 		};
 
 		right-joystick-left {
@@ -104,7 +100,7 @@
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+			gpios = <&pio 0 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA1 */
 		};
 
 		right-joystick-right {
@@ -112,7 +108,7 @@
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+			gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
 		};
 
 		right-joystick-up {
@@ -120,7 +116,7 @@
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+			gpios = <&pio 0 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA3 */
 		};
 
 		right-joystick-down {
@@ -128,7 +124,7 @@
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+			gpios = <&pio 0 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA4 */
 		};
 
 		dpad-left {
@@ -136,7 +132,7 @@
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */
+			gpios = <&pio 7 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH23 */
 		};
 
 		dpad-right {
@@ -144,7 +140,7 @@
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
+			gpios = <&pio 7 24 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH24 */
 		};
 
 		dpad-up {
@@ -152,7 +148,7 @@
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <0xffffffff>; /* -1 */
-			gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
+			gpios = <&pio 7 25 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH25 */
 		};
 
 		dpad-down {
@@ -160,55 +156,55 @@
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
 			linux,input-value = <1>;
-			gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
+			gpios = <&pio 7 26 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH26 */
 		};
 
 		x {
 			label = "Button X";
 			linux,code = <BTN_X>;
-			gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */
+			gpios = <&pio 0 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA16 */
 		};
 
 		y {
 			label = "Button Y";
 			linux,code = <BTN_Y>;
-			gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */
+			gpios = <&pio 0 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA14 */
 		};
 
 		a {
 			label = "Button A";
 			linux,code = <BTN_A>;
-			gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+			gpios = <&pio 0 17 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA17 */
 		};
 
 		b {
 			label = "Button B";
 			linux,code = <BTN_B>;
-			gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */
+			gpios = <&pio 0 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA15 */
 		};
 
 		select {
 			label = "Select Button";
 			linux,code = <BTN_SELECT>;
-			gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+			gpios = <&pio 0 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA11 */
 		};
 
 		start {
 			label = "Start Button";
 			linux,code = <BTN_START>;
-			gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+			gpios = <&pio 0 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA12 */
 		};
 
 		top-left {
 			label = "Top Left Button";
 			linux,code = <BTN_TL>;
-			gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
+			gpios = <&pio 7 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH22 */
 		};
 
 		top-right {
 			label = "Top Right Button";
 			linux,code = <BTN_TR>;
-			gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */
+			gpios = <&pio 0 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA13 */
 		};
 	};
 };
@@ -308,30 +304,6 @@
 	status = "okay";
 };
 
-&pio {
-	key_pins_inet9f: key-pins {
-		pins = "PA0", "PA1", "PA3", "PA4",
-		       "PA5", "PA6", "PA8", "PA9",
-		       "PA11", "PA12", "PA13",
-		       "PA14", "PA15", "PA16", "PA17",
-		       "PH22", "PH23", "PH24", "PH25", "PH26";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
@@ -377,10 +349,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts

@@ -58,7 +58,7 @@
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 

arch/arm/dts/sun4i-a10-jesurun-q5.dts

@@ -63,7 +63,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "q5:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;  /* PH20 */
 		};
@@ -94,7 +94,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 

arch/arm/dts/sun4i-a10-marsboard.dts

@@ -62,22 +62,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red1 {
+		led-0 {
 			label = "marsboard:red1:usr";
 			gpios = <&pio 1 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		red2 {
+		led-1 {
 			label = "marsboard:red2:usr";
 			gpios = <&pio 1 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		red3 {
+		led-2 {
 			label = "marsboard:red3:usr";
 			gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		red4 {
+		led-3 {
 			label = "marsboard:red4:usr";
 			gpios = <&pio 1 8 GPIO_ACTIVE_HIGH>;
 		};
@@ -105,7 +105,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -148,14 +148,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &reg_usb1_vbus {
 	status = "okay";
 };
@@ -183,9 +175,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-olinuxino-lime.dts

@@ -74,7 +74,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinolime>;
 
-		green {
+		led {
 			label = "a10-olinuxino-lime:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -91,12 +91,11 @@
 	/*
 	 * The A10-Lime is known to be unstable when running at 1008 MHz
 	 */
-	operating-points = <
+	operating-points =
 		/* kHz	  uV */
-		912000  1350000
-		864000  1300000
-		624000  1250000
-		>;
+		<912000	1350000>,
+		<864000	1300000>,
+		<624000	1250000>;
 };
 
 &de {
@@ -112,7 +111,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -186,18 +185,6 @@
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
 };
 
 &reg_ahci_5v {
@@ -229,10 +216,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio   = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH5 */
 	usb0_vbus-supply   = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;

arch/arm/dts/sun4i-a10-pcduino.dts

@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		tx {
+		led-0 {
 			label = "pcduino:green:tx";
 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
 		};
 
-		rx {
+		led-1 {
 			label = "pcduino:green:rx";
 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
 		};
@@ -76,8 +76,6 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		back {
 			label = "Key Back";
@@ -112,7 +110,7 @@
 };
 
 &emac {
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -156,14 +154,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 #include "axp209.dtsi"
 
 &reg_dcdc2 {
@@ -203,9 +193,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb1_vbus-supply = <&reg_vcc5v0>; /* USB1 VBUS is always on */
 	usb2_vbus-supply = <&reg_vcc5v0>; /* USB2 VBUS is always on */
 	status = "okay";

arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts

@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
@@ -146,20 +147,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0-vbus-detect-pin {
-		pins = "PH5";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-};
-
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_pin>;
@@ -211,10 +198,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
-	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";

arch/arm/dts/sun4i-a10-topwise-a721.dts

@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 Pascal Roeleven <dev@pascalroeleven.nl>
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Topwise A721";
+	compatible = "topwise,a721", "allwinner,sun4i-a10";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
+		power-supply = <&reg_vbat>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		brightness-levels = <0 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	panel {
+		compatible = "starry,kr070pe2t";
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd_power>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&tcon0_out_panel>;
+			};
+		};
+	};
+
+	reg_lcd_power: reg-lcd-power {
+		compatible = "regulator-fixed";
+		regulator-name = "reg-lcd-power";
+		gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		enable-active-high;
+	};
+
+	reg_vbat: reg-vbat {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	accelerometer@4c {
+		compatible = "fsl,mma7660";
+		reg = <0x4c>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		vcc-supply = <&reg_vcc3v3>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-571 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <571428>;
+	};
+
+	button-761 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <761904>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-ph-supply = <&reg_vcc3v3>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_panel: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&panel_input>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};

arch/arm/dts/sun4i-a10.dtsi

@@ -115,13 +115,12 @@
 			reg = <0x0>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000 1400000
-				912000	1350000
-				864000	1300000
-				624000	1250000
-				>;
+				<1008000 1400000>,
+				<912000	1350000>,
+				<864000	1300000>,
+				<624000	1250000>;
 			#cooling-cells = <2>;
 		};
 	};
@@ -143,7 +142,7 @@
 			trips {
 				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
-					temperature = <850000>;
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
@@ -184,14 +183,34 @@
 		status = "disabled";
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+		default-pool {
+			compatible = "shared-dma-pool";
+			size = <0x6000000>;
+			alloc-ranges = <0x40000000 0x10000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
-		sram-controller@1c00000 {
-			compatible = "allwinner,sun4i-a10-sram-controller";
+		system-control@1c00000 {
+			compatible = "allwinner,sun4i-a10-system-control";
 			reg = <0x01c00000 0x30>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -224,6 +243,19 @@
 					status = "disabled";
 				};
 			};
+
+			sram_c: sram@1d00000 {
+				compatible = "mmio-sram";
+				reg = <0x01d00000 0xd0000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x01d00000 0xd0000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x80000>;
+				};
+			};
 		};
 
 		dma: dma-controller@1c02000 {
@@ -234,7 +266,7 @@
 			#dma-cells = <2>;
 		};
 
-		nfc: nand@1c03000 {
+		nfc: nand-controller@1c03000 {
 			compatible = "allwinner,sun4i-a10-nand";
 			reg = <0x01c03000 0x1000>;
 			interrupts = <37>;
@@ -309,6 +341,7 @@
 				      "tcon-ch0",
 				      "tcon-ch1";
 			clock-output-names = "tcon0-pixel-clock";
+			#clock-cells = <0>;
 			dmas = <&dma SUN4I_DMA_DEDICATED 14>;
 
 			ports {
@@ -358,6 +391,7 @@
 				      "tcon-ch0",
 				      "tcon-ch1";
 			clock-output-names = "tcon1-pixel-clock";
+			#clock-cells = <0>;
 			dmas = <&dma SUN4I_DMA_DEDICATED 15>;
 
 			ports {
@@ -394,6 +428,17 @@
 			};
 		};
 
+		video-codec@1c0e000 {
+			compatible = "allwinner,sun4i-a10-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_VE>;
+			interrupts = <53>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun4i-a10-mmc";
 			reg = <0x01c0f000 0x1000>;
@@ -450,13 +495,14 @@
 			phy-names = "usb";
 			extcon = <&usbphy 0>;
 			allwinner,sram = <&otg_sram 1>;
+			dr_mode = "otg";
 			status = "disabled";
 		};
 
 		usbphy: phy@1c13400 {
 			#phy-cells = <1>;
 			compatible = "allwinner,sun4i-a10-usb-phy";
-			reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+			reg = <0x01c13400 0x10>, <0x01c14800 0x4>, <0x01c1c800 0x4>;
 			reg-names = "phy_ctrl", "pmu1", "pmu2";
 			clocks = <&ccu CLK_USB_PHY>;
 			clock-names = "usb_phy";
@@ -530,8 +576,6 @@
 				};
 
 				hdmi_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 				};
 			};
@@ -579,6 +623,16 @@
 			status = "disabled";
 		};
 
+		csi1: csi@1c1d000 {
+			compatible = "allwinner,sun4i-a10-csi1";
+			reg = <0x01c1d000 0x1000>;
+			interrupts = <43>;
+			clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "ram";
+			resets = <&ccu RST_CSI1>;
+			status = "disabled";
+		};
+
 		spi3: spi@1c1f000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c1f000 0x1000>;
@@ -625,6 +679,31 @@
 				function = "can";
 			};
 
+			/omit-if-no-ref/
+			csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+				pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+				       "PG6", "PG7", "PG8", "PG9", "PG10",
+				       "PG11";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+				pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+				       "PH5", "PH6", "PH7", "PH8", "PH9",
+				       "PH10", "PH11", "PH12", "PH13", "PH14",
+				       "PH15", "PH16", "PH17", "PH18", "PH19",
+				       "PH20", "PH21", "PH22", "PH23", "PH24",
+				       "PH25", "PH26", "PH27";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_clk_pg_pin: csi1-clk-pg-pin {
+				pins = "PG1";
+				function = "csi1";
+			};
+
 			emac_pins: emac0-pins {
 				pins = "PA0", "PA1", "PA2",
 				       "PA3", "PA4", "PA5", "PA6",
@@ -762,13 +841,20 @@
 		timer@1c20c00 {
 			compatible = "allwinner,sun4i-a10-timer";
 			reg = <0x01c20c00 0x90>;
-			interrupts = <22>;
+			interrupts = <22>,
+				     <23>,
+				     <24>,
+				     <25>,
+				     <67>,
+				     <68>;
 			clocks = <&osc24M>;
 		};
 
 		wdt: watchdog@1c20c90 {
 			compatible = "allwinner,sun4i-a10-wdt";
 			reg = <0x01c20c90 0x10>;
+			interrupts = <24>;
+			clocks = <&osc24M>;
 		};
 
 		rtc: rtc@1c20d00 {
@@ -1001,6 +1087,27 @@
 			status = "disabled";
 		};
 
+		mali: gpu@1c40000 {
+			compatible = "allwinner,sun4i-a10-mali", "arm,mali-400";
+			reg = <0x01c40000 0x10000>;
+			interrupts = <69>,
+				     <70>,
+				     <71>,
+				     <72>,
+				     <73>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp0",
+					  "ppmmu0",
+					  "pmu";
+			clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_GPU>;
+
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <384000000>;
+		};
+
 		fe0: display-frontend@1e00000 {
 			compatible = "allwinner,sun4i-a10-display-frontend";
 			reg = <0x01e00000 0x20000>;

arch/arm/dts/sun50i-a64-cpu-opp.dtsi

@@ -4,7 +4,7 @@
  */
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 

arch/arm/dts/sun50i-a64-orangepi-win.dts

@@ -343,7 +343,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <80000000>;

arch/arm/dts/sun50i-a64-pinebook.dts

@@ -15,6 +15,7 @@
 / {
 	model = "Pinebook";
 	compatible = "pine64,pinebook", "allwinner,sun50i-a64";
+	chassis-type = "laptop";
 
 	aliases {
 		serial0 = &uart0;

arch/arm/dts/sun50i-a64-pinephone.dtsi

@@ -12,6 +12,8 @@
 #include <dt-bindings/pwm/pwm.h>
 
 / {
+	chassis-type = "handset";
+
 	aliases {
 		ethernet0 = &rtl8723cs;
 		serial0 = &uart0;
@@ -25,6 +27,11 @@
 		/* Backlight configuration differs per PinePhone revision. */
 	};
 
+	bt_sco_codec: bt-sco-codec {
+		#sound-dai-cells = <1>;
+		compatible = "linux,bt-sco";
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -91,6 +98,8 @@
 };
 
 &codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&aif3_pins>;
 	status = "okay";
 };
 
@@ -426,6 +435,7 @@
 
 &sound {
 	status = "okay";
+	simple-audio-card,name = "PinePhone";
 	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
 	simple-audio-card,widgets = "Microphone", "Headset Microphone",
 				    "Microphone", "Internal Microphone",
@@ -447,6 +457,23 @@
 			"MIC1", "Internal Microphone",
 			"Headset Microphone", "HBIAS",
 			"MIC2", "Headset Microphone";
+
+	simple-audio-card,dai-link@2 {
+		format = "dsp_a";
+		frame-master = <&link2_codec>;
+		bitclock-master = <&link2_codec>;
+		bitclock-inversion;
+
+		link2_cpu: cpu {
+			sound-dai = <&bt_sco_codec 0>;
+		};
+
+		link2_codec: codec {
+			sound-dai = <&codec 2>;
+			dai-tdm-slot-num = <1>;
+			dai-tdm-slot-width = <32>;
+		};
+	};
 };
 
 &uart0 {

arch/arm/dts/sun50i-a64-pinetab.dts

@@ -16,6 +16,7 @@
 / {
 	model = "PineTab, Development Sample";
 	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+	chassis-type = "tablet";
 
 	aliases {
 		serial0 = &uart0;
@@ -35,6 +36,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "c";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	i2c-csi {
 		compatible = "i2c-gpio";
 		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
@@ -77,7 +89,7 @@
 		sound-name-prefix = "Speaker Amp";
 	};
 
-	vdd_bl: regulator@0 {
+	vdd_bl: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "bl-3v3";
 		regulator-min-microvolt = <3300000>;
@@ -410,6 +422,21 @@
 	regulator-name = "vcc-rtc";
 };
 
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dldo1>;
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &sound {
 	status = "okay";
 	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;

arch/arm/dts/sun50i-a64-teres-i.dts

@@ -14,6 +14,7 @@
 / {
 	model = "Olimex A64 Teres-I";
 	compatible = "olimex,a64-teres-i", "allwinner,sun50i-a64";
+	chassis-type = "laptop";
 
 	aliases {
 		serial0 = &uart0;
@@ -139,6 +140,8 @@
 			#size-cells = <0>;
 
 			port@0 {
+				reg = <0>;
+
 				anx6345_in: endpoint {
 					remote-endpoint = <&tcon0_out_anx6345>;
 				};
@@ -206,7 +209,6 @@
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		wakeup-source;
 	};
 };
 

arch/arm/dts/sun50i-a64.dtsi

@@ -102,6 +102,22 @@
 		status = "disabled";
 	};
 
+	gpu_opp_table: opp-table-gpu {
+		compatible = "operating-points-v2";
+
+		opp-120000000 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+
+		opp-312000000 {
+			opp-hz = /bits/ 64 <312000000>;
+		};
+
+		opp-432000000 {
+			opp-hz = /bits/ 64 <432000000>;
+		};
+	};
+
 	osc24M: osc24M_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
@@ -131,12 +147,10 @@
 	};
 
 	sound: sound {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "sun50i-a64-audio";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,frame-master = <&cpudai>;
-		simple-audio-card,bitclock-master = <&cpudai>;
-		simple-audio-card,mclk-fs = <128>;
 		simple-audio-card,aux-devs = <&codec_analog>;
 		simple-audio-card,routing =
 				"Left DAC", "DACL",
@@ -145,12 +159,19 @@
 				"ADCR", "Right ADC";
 		status = "disabled";
 
-		cpudai: simple-audio-card,cpu {
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			frame-master = <&link0_cpu>;
+			bitclock-master = <&link0_cpu>;
+			mclk-fs = <128>;
+
+			link0_cpu: cpu {
 				sound-dai = <&dai>;
 			};
 
-		link_codec: simple-audio-card,codec {
-			sound-dai = <&codec>;
+			link0_codec: codec {
+				sound-dai = <&codec 0>;
+			};
 		};
 	};
 
@@ -658,6 +679,18 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			/omit-if-no-ref/
+			aif2_pins: aif2-pins {
+				pins = "PB4", "PB5", "PB6", "PB7";
+				function = "aif2";
+			};
+
+			/omit-if-no-ref/
+			aif3_pins: aif3-pins {
+				pins = "PG10", "PG11", "PG12", "PG13";
+				function = "aif3";
+			};
+
 			csi_pins: csi-pins {
 				pins = "PE0", "PE2", "PE3", "PE4", "PE5", "PE6",
 				       "PE7", "PE8", "PE9", "PE10", "PE11";
@@ -798,6 +831,23 @@
 			};
 		};
 
+		timer@1c20c00 {
+			compatible = "allwinner,sun50i-a64-timer",
+				     "allwinner,sun8i-a23-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog@1c20ca0 {
+			compatible = "allwinner,sun50i-a64-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
 		spdif: spdif@1c21000 {
 			#sound-dai-cells = <0>;
 			compatible = "allwinner,sun50i-a64-spdif",
@@ -878,7 +928,7 @@
 		};
 
 		codec: codec@1c22e00 {
-			#sound-dai-cells = <0>;
+			#sound-dai-cells = <1>;
 			compatible = "allwinner,sun50i-a64-codec",
 				     "allwinner,sun8i-a33-codec";
 			reg = <0x01c22e00 0x600>;
@@ -1067,6 +1117,7 @@
 			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
 			clock-names = "bus", "core";
 			resets = <&ccu RST_BUS_GPU>;
+			operating-points-v2 = <&gpu_opp_table>;
 		};
 
 		gic: interrupt-controller@1c81000 {
@@ -1093,8 +1144,14 @@
 
 		mbus: dram-controller@1c62000 {
 			compatible = "allwinner,sun50i-a64-mbus";
-			reg = <0x01c62000 0x1000>;
-			clocks = <&ccu 112>;
+			reg = <0x01c62000 0x1000>,
+			      <0x01c63000 0x1000>;
+			reg-names = "mbus", "dram";
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
@@ -1167,8 +1224,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc 0>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -1321,13 +1378,5 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
-
-		wdt0: watchdog@1c20ca0 {
-			compatible = "allwinner,sun50i-a64-wdt",
-				     "allwinner,sun6i-a31-wdt";
-			reg = <0x01c20ca0 0x20>;
-			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&osc24M>;
-		};
 	};
 };

arch/arm/dts/sun50i-h5-cpu-opp.dtsi

@@ -2,7 +2,7 @@
 // Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 

arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts

@@ -142,9 +142,16 @@
 	status = "okay";
 
 	eeprom@51 {
-		compatible = "microchip,24c02";
+		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x51>;
 		pagesize = <16>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth_mac1: mac-address@fa {
+			reg = <0xfa 0x06>;
+		};
 	};
 };
 

arch/arm/dts/sun50i-h5.dtsi

@@ -217,7 +217,7 @@
 			};
 		};
 
-		gpu_thermal {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
@@ -233,6 +233,10 @@
 	compatible = "allwinner,sun50i-h5-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun50i-h5-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun50i-h5-mmc",
 		     "allwinner,sun50i-a64-mmc";

arch/arm/dts/sun50i-h6-beelink-gs1.dts

@@ -150,12 +150,28 @@
 	vcc-pg-supply = <&reg_aldo1>;
 };
 
-&r_i2c {
+&r_ir {
+	linux,rc-map-name = "rc-beelink-gs1";
+	status = "okay";
+};
+
+&r_pio {
+	/*
+	 * FIXME: We can't add that supply for now since it would
+	 * create a circular dependency between pinctrl, the regulator
+	 * and the RSB Bus.
+	 *
+	 * vcc-pl-supply = <&reg_aldo1>;
+	 */
+	vcc-pm-supply = <&reg_aldo1>;
+};
+
+&r_rsb {
 	status = "okay";
 
-	axp805: pmic@36 {
+	axp805: pmic@745 {
 		compatible = "x-powers,axp805", "x-powers,axp806";
-		reg = <0x36>;
+		reg = <0x745>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
@@ -273,22 +289,6 @@
 	};
 };
 
-&r_ir {
-	linux,rc-map-name = "rc-beelink-gs1";
-	status = "okay";
-};
-
-&r_pio {
-	/*
-	 * PL0 and PL1 are used for PMIC I2C
-	 * don't enable the pl-supply else
-	 * it will fail at boot
-	 *
-	 * vcc-pl-supply = <&reg_aldo1>;
-	 */
-	vcc-pm-supply = <&reg_aldo1>;
-};
-
 &spdif {
 	status = "okay";
 };

arch/arm/dts/sun50i-h6-cpu-opp.dtsi

@@ -3,7 +3,7 @@
 // Copyright (C) 2020 Clément Péron <peron.clem@gmail.com>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "allwinner,sun50i-h6-operating-points";
 		nvmem-cells = <&cpu_speed_grade>;
 		opp-shared;

arch/arm/dts/sun50i-h6-orangepi-3.dts

@@ -175,12 +175,16 @@
 	vcc-pg-supply = <&reg_vcc_wifi_io>;
 };
 
-&r_i2c {
+&r_ir {
+	status = "okay";
+};
+
+&r_rsb {
 	status = "okay";
 
-	axp805: pmic@36 {
+	axp805: pmic@745 {
 		compatible = "x-powers,axp805", "x-powers,axp806";
-		reg = <0x36>;
+		reg = <0x745>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
@@ -291,10 +295,6 @@
 	};
 };
 
-&r_ir {
-	status = "okay";
-};
-
 &rtc {
 	clocks = <&ext_osc32k>;
 };

arch/arm/dts/sun50i-h6-orangepi.dtsi

@@ -112,12 +112,20 @@
 	vcc-pg-supply = <&reg_aldo1>;
 };
 
-&r_i2c {
+&r_ir {
+	status = "okay";
+};
+
+&r_pio {
+	vcc-pm-supply = <&reg_bldo3>;
+};
+
+&r_rsb {
 	status = "okay";
 
-	axp805: pmic@36 {
+	axp805: pmic@745 {
 		compatible = "x-powers,axp805", "x-powers,axp806";
-		reg = <0x36>;
+		reg = <0x745>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
@@ -232,14 +240,6 @@
 	};
 };
 
-&r_ir {
-	status = "okay";
-};
-
-&r_pio {
-	vcc-pm-supply = <&reg_bldo3>;
-};
-
 &rtc {
 	clocks = <&ext_osc32k>;
 };

arch/arm/dts/sun50i-h6-pine-h64-model-b.dts

@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019 Corentin LABBE <clabbe@baylibre.com>
+ */
+
+#include "sun50i-h6-pine-h64.dts"
+
+/ {
+	model = "Pine H64 model B";
+	compatible = "pine64,pine-h64-model-b", "allwinner,sun50i-h6";
+
+	/delete-node/ reg_gmac_3v3;
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&hdmi_connector {
+	/delete-property/ ddc-en-gpios;
+};
+
+&emac {
+	phy-supply = <&reg_aldo2>;
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_cldo3>;
+	vqmmc-supply = <&reg_aldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+		host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
+		enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+		max-speed = <1500000>;
+	};
+};

arch/arm/dts/sun50i-h6-pine-h64.dts

@@ -89,6 +89,10 @@
 	status = "okay";
 };
 
+&dwc3 {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -332,3 +336,7 @@
 	usb3_vbus-supply = <&reg_usb_vbus>;
 	status = "okay";
 };
+
+&usb3phy {
+	status = "okay";
+};

arch/arm/dts/sun50i-h6-tanix-tx6-mini.dts

@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2021 Jernej Skrabec <jernej.skrabec@gmail.com>
+
+/dts-v1/;
+
+#include "sun50i-h6-tanix.dtsi"
+
+/ {
+	model = "Tanix TX6 mini";
+	compatible = "oranth,tanix-tx6-mini", "allwinner,sun50i-h6";
+};
+
+&r_ir {
+	linux,rc-map-name = "rc-tanix-tx3mini";
+};

arch/arm/dts/sun50i-h6-tanix-tx6.dts

@@ -3,122 +3,27 @@
 
 /dts-v1/;
 
-#include "sun50i-h6.dtsi"
-#include "sun50i-h6-cpu-opp.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
+#include "sun50i-h6-tanix.dtsi"
 
 / {
 	model = "Tanix TX6";
 	compatible = "oranth,tanix-tx6", "allwinner,sun50i-h6";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	connector {
-		compatible = "hdmi-connector";
-		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&hdmi_out_con>;
-			};
-		};
-	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_vdd_cpu_gpu: vdd-cpu-gpu {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd-cpu-gpu";
-		regulator-min-microvolt = <1135000>;
-		regulator-max-microvolt = <1135000>;
-	};
-};
-
-&cpu0 {
-	cpu-supply = <&reg_vdd_cpu_gpu>;
-};
-
-&de {
-	status = "okay";
-};
-
-&dwc3 {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci3 {
-	status = "okay";
-};
-
-&gpu {
-	mali-supply = <&reg_vdd_cpu_gpu>;
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_out {
-	hdmi_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci3 {
-	status = "okay";
 };
 
 &r_ir {
 	linux,rc-map-name = "rc-tanix-tx5max";
-	status = "okay";
 };
 
-&uart0 {
+&uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_ph_pins>;
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
-};
 
-&usb2otg {
-	dr_mode = "host";
-	status = "okay";
+	bluetooth {
+		compatible = "realtek,rtl8822cs-bt";
+		device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+		host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
+		enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
 	};
-
-&usb2phy {
-	status = "okay";
-};
-
-&usb3phy {
-	status = "okay";
 };

arch/arm/dts/sun50i-h6-tanix.dtsi

@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2019 Jernej Skrabec <jernej.skrabec@siol.net>
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+#include "sun50i-h6-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	/* used for FD650 LED display driver */
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 7 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PH6 */
+		scl-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PH5 */
+		i2c-gpio,delay-us = <5>;
+	};
+
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vdd_cpu_gpu: regulator-vdd-cpu-gpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu-gpu";
+		regulator-min-microvolt = <1135000>;
+		regulator-max-microvolt = <1135000>;
+	};
+
+	sound-spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sun50i-h6-spdif";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu_gpu>;
+};
+
+&de {
+	status = "okay";
+};
+
+&dwc3 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&reg_vdd_cpu_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_vcc1v8>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc1v8>;
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usb2otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb2phy {
+	status = "okay";
+};
+
+&usb3phy {
+	status = "okay";
+};

arch/arm/dts/sun50i-h6.dtsi

@@ -119,10 +119,10 @@
 			display_clocks: clock@0 {
 				compatible = "allwinner,sun50i-h6-de3-clk";
 				reg = <0x0 0x10000>;
-				clocks = <&ccu CLK_DE>,
-					 <&ccu CLK_BUS_DE>;
-				clock-names = "mod",
-					      "bus";
+				clocks = <&ccu CLK_BUS_DE>,
+					 <&ccu CLK_DE>;
+				clock-names = "bus",
+					      "mod";
 				resets = <&ccu RST_BUS_DE>;
 				#clock-cells = <1>;
 				#reset-cells = <1>;
@@ -153,6 +153,15 @@
 			};
 		};
 
+		video-codec-g2@1c00000 {
+			compatible = "allwinner,sun50i-h6-vpu-g2";
+			reg = <0x01c00000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_VP9>, <&ccu CLK_VP9>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_VP9>;
+		};
+
 		video-codec@1c0e000 {
 			compatible = "allwinner,sun50i-h6-video-engine";
 			reg = <0x01c0e000 0x2000>;
@@ -271,6 +280,15 @@
 			};
 		};
 
+		timer@3009000 {
+			compatible = "allwinner,sun50i-h6-timer",
+				     "allwinner,sun8i-a23-timer";
+			reg = <0x03009000 0xa0>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
 		watchdog: watchdog@30090a0 {
 			compatible = "allwinner,sun50i-h6-wdt",
 				     "allwinner,sun6i-a31-wdt";

arch/arm/dts/sun5i-a10s-auxtek-t003.dts

@@ -62,7 +62,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_t003>;
 
-		red {
+		led {
 			label = "t003-tv-dongle:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 			default-state = "on";
@@ -75,8 +75,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp152: pmic@30 {
@@ -89,8 +87,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -106,13 +102,7 @@
 };
 
 &pio {
-	mmc0_cd_pin_t003: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_t003: led_pins@0 {
+	led_pins_t003: led-pin {
 		pins = "PB2";
 		function = "gpio_out";
 		drive-strength = <20>;
@@ -131,7 +121,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun5i-a10s-auxtek-t004.dts

@@ -62,7 +62,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_t004>;
 
-		red {
+		led {
 			label = "t004-tv-dongle:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 			default-state = "on";
@@ -71,8 +71,6 @@
 
 	reg_vmmc1: vmmc1 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mmc1_vcc_en_pin_t004>;
 		regulator-name = "vmmc1";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -86,8 +84,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp152: pmic@30 {
@@ -100,8 +96,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -109,8 +103,6 @@
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vmmc1>;
 	bus-width = <4>;
 	non-removable;
@@ -127,24 +119,7 @@
 };
 
 &pio {
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG12";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	mmc0_cd_pin_t004: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
-		pins = "PB18";
-		function = "gpio_out";
-	};
-
-	led_pins_t004: led_pins@0 {
+	led_pins_t004: led-pin {
 		pins = "PB2";
 		function = "gpio_out";
 		drive-strength = <20>;
@@ -158,7 +133,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
@@ -168,9 +143,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_id_det-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };

arch/arm/dts/sun5i-a10s-mk802.dts

@@ -59,10 +59,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_mk802>;
 
-		red {
+		led {
 			label = "mk802:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 		};
@@ -74,8 +72,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp152: pmic@30 {
@@ -88,8 +84,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -97,8 +91,6 @@
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	non-removable;
@@ -113,33 +105,14 @@
 	status = "okay";
 };
 
-&pio {
-	led_pins_mk802: led_pins@0 {
-		pins = "PB2";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_mk802: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb1_vbus_pin_mk802: usb1_vbus_pin@0 {
-		pins = "PB10";
-		function = "gpio_out";
-	};
-};
-
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_mk802>;
 	gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun5i-a10s-olinuxino-micro.dts

@@ -79,7 +79,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxino>;
 
-		green {
+		led {
 			label = "a10s-olinuxino-micro:green:usr";
 			gpios = <&pio 4 3 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -97,8 +97,8 @@
 
 &emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emac_pins_b>;
-	phy = <&phy1>;
+	pinctrl-0 = <&emac_pa_pins>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -117,8 +117,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp152: pmic@30 {
@@ -130,11 +128,9 @@
 #include "axp152.dtsi"
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c16";
 		pagesize = <16>;
 		reg = <0x50>;
@@ -143,8 +139,6 @@
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 };
 
@@ -152,35 +146,35 @@
 	vref-supply = <&reg_vcc3v0>;
 	status = "okay";
 
-	button@191 {
+	button-191 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <191274>;
 	};
 
-	button@392 {
+	button-392 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
 		voltage = <392644>;
 	};
 
-	button@601 {
+	button-601 {
 		label = "Menu";
 		linux,code = <KEY_MENU>;
 		channel = <0>;
 		voltage = <601151>;
 	};
 
-	button@795 {
+	button-795 {
 		label = "Enter";
 		linux,code = <KEY_ENTER>;
 		channel = <0>;
 		voltage = <795090>;
 	};
 
-	button@987 {
+	button-987 {
 		label = "Home";
 		linux,code = <KEY_HOMEPAGE>;
 		channel = <0>;
@@ -197,8 +191,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -206,8 +198,6 @@
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */
@@ -223,34 +213,11 @@
 };
 
 &pio {
-	mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	mmc1_cd_pin_olinuxino_micro: mmc1_cd_pin@0 {
-		pins = "PG13";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_olinuxino: led_pins@0 {
+	led_pins_olinuxino: led-pin {
 		pins = "PE3";
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 {
-		pins = "PB10";
-		function = "gpio_out";
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG12";
-		function = "gpio_in";
-		bias-pull-up;
-	};
 };
 
 &reg_usb0_vbus {
@@ -259,15 +226,14 @@
 };
 
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>;
 	gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &spi2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_b>,
-		    <&spi2_cs0_pins_b>;
+	pinctrl-0 = <&spi2_pb_pins>,
+		    <&spi2_cs0_pb_pin>;
 	status = "okay";
 };
 
@@ -277,19 +243,19 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
 &uart2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins_b>;
+	pinctrl-0 = <&uart2_pc_pins>;
 	status = "okay";
 };
 
 &uart3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_a>;
+	pinctrl-0 = <&uart3_pg_pins>;
 	status = "okay";
 };
 
@@ -299,9 +265,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_id_det-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";

arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts

@@ -63,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_r7>;
 
-		green {
+		led {
 			label = "r7-tv-dongle:green:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -76,8 +76,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -85,8 +83,6 @@
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	non-removable;
@@ -98,33 +94,21 @@
 };
 
 &pio {
-	mmc0_cd_pin_r7: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_r7: led_pins@0 {
+	led_pins_r7: led-pin {
 		pins = "PB2";
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb1_vbus_pin_r7: usb1_vbus_pin@0 {
-		pins = "PG13";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_r7>;
 	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun5i-a10s-wobo-i5.dts

@@ -61,10 +61,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_wobo_i5>;
 
-		blue {
+		led {
 			label = "a10s-wobo-i5:blue:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -73,8 +71,6 @@
 
 	reg_emac_3v3: emac-3v3 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&emac_power_pin_wobo>;
 		regulator-name = "emac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -94,8 +90,8 @@
 
 &emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emac_pins_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&emac_pd_pins>;
+	phy-handle = <&phy1>;
 	status = "okay";
 };
 
@@ -104,8 +100,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -126,8 +120,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */
@@ -142,24 +134,6 @@
 	status = "okay";
 };
 
-&pio {
-	led_pins_wobo_i5: led_pins@0 {
-		pins = "PB2";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 {
-		pins = "PB3";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	emac_power_pin_wobo: emac_power_pin@0 {
-		pins = "PA02";
-		function = "gpio_out";
-	};
-};
-
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
@@ -206,7 +180,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun5i-a10s.dtsi

@@ -42,15 +42,11 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "skeleton.dtsi"
-
 #include "sun5i.dtsi"
 
 #include <dt-bindings/dma/sun4i-a10.h>
 
 / {
-	interrupt-parent = <&intc>;
-
 	aliases {
 		ethernet0 = &emac;
 	};
@@ -60,7 +56,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		framebuffer@2 {
+		framebuffer-lcd0-hdmi {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
@@ -76,7 +72,7 @@
 		allwinner,pipelines = <&fe0>;
 	};
 
-	soc@1c00000 {
+	soc {
 		hdmi: hdmi@1c16000 {
 			compatible = "allwinner,sun5i-a10s-hdmi";
 			reg = <0x01c16000 0x1000>;
@@ -104,8 +100,6 @@
 				};
 
 				hdmi_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 				};
 			};
@@ -125,20 +119,25 @@
 	compatible = "allwinner,sun5i-a10s-ccu";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
 &pio {
 	compatible = "allwinner,sun5i-a10s-pinctrl";
 
-	uart0_pins_a: uart0@0 {
+	uart0_pb_pins: uart0-pb-pins {
 		pins = "PB19", "PB20";
 		function = "uart0";
 	};
 
-	uart2_pins_b: uart2@1 {
+	uart2_pc_pins: uart2-pc-pins {
 		pins = "PC18", "PC19";
 		function = "uart2";
 	};
 
-	emac_pins_b: emac0@1 {
+	emac_pa_pins: emac-pa-pins {
 		pins = "PA0", "PA1", "PA2",
 				"PA3", "PA4", "PA5", "PA6",
 				"PA7", "PA8", "PA9", "PA10",
@@ -147,27 +146,24 @@
 		function = "emac";
 	};
 
-	mmc1_pins_a: mmc1@0 {
+	mmc1_pins: mmc1-pins {
 		pins = "PG3", "PG4", "PG5",
 				 "PG6", "PG7", "PG8";
 		function = "mmc1";
 		drive-strength = <30>;
 	};
 
-	spi2_pins_b: spi2@1 {
+	spi2_pb_pins: spi2-pb-pins {
 		pins = "PB12", "PB13", "PB14";
 		function = "spi2";
 	};
 
-	spi2_cs0_pins_b: spi2_cs0@1 {
+	spi2_cs0_pb_pin: spi2-cs0-pb-pin {
 		pins = "PB11";
 		function = "spi2";
 	};
 };
 
-&sram_a {
-};
-
 &tcon0_out {
 	tcon0_out_hdmi: endpoint@2 {
 		reg = <2>;

arch/arm/dts/sun5i-a13-ampe-a76.dts

@@ -26,3 +26,7 @@
 	pinctrl-0 = <&uart1_pins_b>;
 	status = "okay";
 };
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+};

arch/arm/dts/sun5i-a13-empire-electronix-d709.dts

@@ -61,6 +61,7 @@
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
+		power-supply = <&reg_vcc3v3>;
 		/* TODO: backlight uses axp gpio1 as enable pin */
 	};
 
@@ -78,8 +79,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -91,8 +90,6 @@
 #include "axp209.dtsi"
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 
 	pcf8563: rtc@51 {
@@ -105,14 +102,14 @@
 	vref-supply = <&reg_ldo2>;
 	status = "okay";
 
-	button@200 {
+	button-200 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <200000>;
 	};
 
-	button@400 {
+	button-400 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
@@ -121,8 +118,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -133,29 +128,9 @@
 	status = "okay";
 };
 
-&pio {
-	mmc0_cd_pin_d709: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &pwm {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_pins>;
+	pinctrl-0 = <&pwm0_pin>;
 	status = "okay";
 };
 
@@ -197,7 +172,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -207,10 +182,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_ldo3>;
 	status = "okay";

arch/arm/dts/sun5i-a13-hsg-h702.dts

@@ -69,8 +69,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -80,8 +78,6 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 
 	pcf8563: rtc@51 {
@@ -91,8 +87,6 @@
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 };
 
@@ -100,14 +94,14 @@
 	vref-supply = <&reg_ldo2>;
 	status = "okay";
 
-	button@200 {
+	button-200 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <200000>;
 	};
 
-	button@400 {
+	button-400 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
@@ -116,8 +110,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -132,25 +124,6 @@
 	status = "okay";
 };
 
-&pio {
-	mmc0_cd_pin_h702: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-	};
-};
-
 #include "axp209.dtsi"
 
 &reg_dcdc2 {
@@ -191,7 +164,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -201,9 +174,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
 	usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_ldo3>;

arch/arm/dts/sun5i-a13-licheepi-one.dts

@@ -0,0 +1,214 @@
+/*
+ * Copyright 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun5i-a13-olinuxino.dts, which is
+ *   Copyright 2012 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *   Copyright 2013 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Lichee Pi One";
+	compatible = "licheepi,licheepi-one", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label ="licheepi:red:usr";
+			gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			label ="licheepi:green:usr";
+			gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-2 {
+			label ="licheepi:blue:usr";
+			gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
+		};
+
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupts = <0>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
+&i2c1 {
+	status = "disabled";
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-984 {
+		label = "Home";
+		linux,code = <KEY_HOMEPAGE>;
+		channel = <0>;
+		voltage = <984126>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "csi-1.8v";
+};
+
+&reg_ldo4 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "csi-2.8v";
+};
+
+&reg_usb0_vbus {
+	gpio = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};

arch/arm/dts/sun5i-a13-olinuxino-micro.dts

@@ -64,7 +64,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinom>;
 
-		power {
+		led {
 			label = "a13-olinuxino-micro:green:power";
 			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -77,26 +77,18 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -112,56 +104,26 @@
 };
 
 &pio {
-	mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_olinuxinom: led_pins@0 {
+	led_pins_olinuxinom: led-pin {
 		pins = "PG9";
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-
-	usb0_vbus_pin_olinuxinom: usb0_vbus_pin@0 {
-		pins = "PG12";
-		function = "gpio_out";
-	};
-
-	usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
-		pins = "PG11";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb0_vbus {
-	pinctrl-0 = <&usb0_vbus_pin_olinuxinom>;
 	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
 	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -171,10 +133,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";

arch/arm/dts/sun5i-a13-olinuxino.dts

@@ -66,7 +66,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxino>;
 
-		power {
+		led {
 			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
@@ -74,8 +74,6 @@
 
 	bridge {
 		compatible = "dumb-vga-dac";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		ports {
 			#address-cells = <1>;
@@ -123,8 +121,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -138,14 +134,10 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 };
 
@@ -153,35 +145,35 @@
 	vref-supply = <&reg_vcc3v0>;
 	status = "okay";
 
-	button@191 {
+	button-191 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <191274>;
 	};
 
-	button@392 {
+	button-392 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
 		voltage = <392644>;
 	};
 
-	button@601 {
+	button-601 {
 		label = "Menu";
 		linux,code = <KEY_MENU>;
 		channel = <0>;
 		voltage = <601151>;
 	};
 
-	button@795 {
+	button-795 {
 		label = "Enter";
 		linux,code = <KEY_ENTER>;
 		channel = <0>;
 		voltage = <795090>;
 	};
 
-	button@987 {
+	button-987 {
 		label = "Home";
 		linux,code = <KEY_HOMEPAGE>;
 		channel = <0>;
@@ -190,8 +182,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -207,34 +197,11 @@
 };
 
 &pio {
-	mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_olinuxino: led_pins@0 {
+	led_pins_olinuxino: led-pin {
 		pins = "PG9";
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-
-	usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 {
-		pins = "PG11";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb0_vbus {
@@ -243,7 +210,6 @@
 };
 
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_olinuxino>;
 	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -263,7 +229,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -273,10 +239,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";

arch/arm/dts/sun5i-a13-pocketbook-touch-lux-3.dts

@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright 2019 Ondrej Jirman <megous@megous.com>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PocketBook Touch Lux 3";
+	compatible = "pocketbook,touch-lux-3", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_vcc3v3>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+			default-state = "on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		label = "GPIO Keys";
+
+		key-right {
+			label = "Right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&pio 6 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG9 */
+		};
+
+		key-left {
+			label = "Left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&pio 6 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG10 */
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-1v8-nor-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_1v8_nor: regulator-nor {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-nor";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+		regulator-always-on;
+	};
+
+	reg_1v8_ctp: regulator-ctp {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+	};
+
+	reg_3v3_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mmc0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+		vin-supply = <&reg_vcc3v3>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	status = "okay";
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* Touchpanel is connected here. */
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-200 {
+		label = "Home";
+		linux,code = <KEY_HOME>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_3v3_mmc0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-int-pll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+	/* We need this otherwise the LDO3 would overload */
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pe_pins>, <&spi2_cs0_pe_pin>;
+	status = "okay";
+
+	epd_flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "macronix,mx25u4033", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_ldo3>;
+	status = "okay";
+};

arch/arm/dts/sun5i-a13-q8-tablet.dts

@@ -49,19 +49,13 @@
 	compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
 
 	panel: panel {
-		compatible = "urt,umsh-8596md-t", "simple-panel";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			/* TODO: lcd panel uses axp gpio0 as enable pin */
+		compatible = "bananapi,s070wv20-ct16";
+		power-supply = <&reg_vcc3v3>;
+		enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */
 		backlight = <&backlight>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 
-			panel_input: endpoint@0 {
-				reg = <0>;
+		port {
+			panel_input: endpoint {
 				remote-endpoint = <&tcon0_out_lcd>;
 			};
 		};

arch/arm/dts/sun5i-a13-utoo-p66.dts

@@ -58,13 +58,11 @@
 		/delete-property/stdout-path;
 	};
 
-	i2c_lcd: i2c@0 {
+	i2c_lcd: i2c {
 		/* The lcd panel i2c interface is hooked up via gpios */
 		compatible = "i2c-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_lcd_pins>;
-		gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>, /* PG12, sda */
-			<&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10, scl */
+		sda-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
+		scl-gpios = <&pio 6 10 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG10 */
 		i2c-gpio,delay-us = <5>;
 	};
 };
@@ -79,13 +77,9 @@
 	allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
 };
 
-&codec_pa_pin {
-	pins = "PG3";
-};
-
 &mmc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_a>;
+	pinctrl-0 = <&mmc2_8bit_pins>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <8>;
 	non-removable;
@@ -98,14 +92,6 @@
 	};
 };
 
-&pio {
-	i2c_lcd_pins: i2c_lcd_pin@0 {
-		pins = "PG10", "PG12";
-		function = "gpio_out";
-		bias-pull-up;
-	};
-};
-
 &reg_usb0_vbus {
 	gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
 };
@@ -128,7 +114,3 @@
 	/* The P66 uses the uart pins as gpios */
 	status = "disabled";
 };
-
-&usb0_vbus_pin_a {
-	pins = "PB4";
-};

arch/arm/dts/sun5i-a13.dtsi

@@ -42,17 +42,13 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "skeleton.dtsi"
-
 #include "sun5i.dtsi"
 
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	interrupt-parent = <&intc>;
-
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -88,7 +84,7 @@
 		allwinner,pipelines = <&fe0>;
 	};
 
-	soc@1c00000 {
+	soc {
 		pwm: pwm@1c20e00 {
 			compatible = "allwinner,sun5i-a13-pwm";
 			reg = <0x01c20e00 0xc>;
@@ -106,15 +102,14 @@
 
 &cpu0 {
 	clock-latency = <244144>; /* 8 32k periods */
-	operating-points = <
+	operating-points =
 		/* kHz	  uV */
-		1008000 1400000
-		912000	1350000
-		864000	1300000
-		624000	1200000
-		576000	1200000
-		432000	1200000
-		>;
+		<1008000 1400000>,
+		<912000 1350000>,
+		<864000 1300000>,
+		<624000 1200000>,
+		<576000 1200000>,
+		<432000 1200000>;
 	#cooling-cells = <2>;
 };
 

arch/arm/dts/sun5i-gr8-chip-pro.dts

@@ -79,8 +79,6 @@
 
 	mmc0_pwrseq: mmc0_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_reg_on_pin_chip_pro>;
 		reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
 	};
 };
@@ -94,8 +92,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -114,20 +110,16 @@
 #include "axp209.dtsi"
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "disabled";
 };
 
 &i2s0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&i2s0_mclk_pins_a>, <&i2s0_data_pins_a>;
+	pinctrl-0 = <&i2s0_mclk_pin>, <&i2s0_data_pins>;
 	status = "disabled";
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&mmc0_pwrseq>;
 	bus-width = <4>;
@@ -137,12 +129,10 @@
 
 &nfc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
+	pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
 	status = "okay";
 
 	nand@0 {
-		#address-cells = <2>;
-		#size-cells = <2>;
 		reg = <0>;
 		allwinner,rb = <0>;
 		nand-ecc-mode = "hw";
@@ -157,21 +147,9 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_pin_chip_pro: usb0-id-pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-	};
-
-	wifi_reg_on_pin_chip_pro: wifi-reg-on-pin@0 {
-		pins = "PB10";
-		function = "gpio_out";
-	};
-};
-
 &pwm {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_pins>, <&pwm1_pins>;
+	pinctrl-0 = <&pwm0_pin>, <&pwm1_pins>;
 	status = "disabled";
 };
 
@@ -220,19 +198,19 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>, <&uart1_cts_rts_pins_a>;
+	pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pins>;
 	status = "okay";
 };
 
 &uart2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins_a>, <&uart2_cts_rts_pins_a>;
+	pinctrl-0 = <&uart2_pd_pins>, <&uart2_cts_rts_pd_pins>;
 	status = "disabled";
 };
 
 &uart3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_a>, <&uart3_cts_rts_pins_a>;
+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_cts_rts_pg_pins>;
 	status = "okay";
 };
 
@@ -253,9 +231,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_pin_chip_pro>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb1_vbus-supply = <&reg_vcc5v0>;
 	status = "okay";

arch/arm/dts/sun5i-gr8-evb.dts

@@ -0,0 +1,333 @@
+/*
+ * Copyright 2016 Free Electrons
+ * Copyright 2016 NextThing Co
+ *
+ * Mylène Josserand <mylene.josserand@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-gr8.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NextThing GR8-EVB";
+	compatible = "nextthing,gr8-evb", "nextthing,gr8";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 10000 0>;
+		enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_vcc3v3>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+	};
+
+	sound-analog {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "gr8-evb-wm8978";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <512>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&wm8978>;
+		};
+	};
+
+	sound-spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "On-board SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&be0 {
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+
+		/*
+		* The interrupt is routed through the "External Fast
+		* Interrupt Request" pin (ball G13 of the module)
+		* directly to the main interrupt controller, without
+		* any other controller interfering.
+		*/
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	status = "okay";
+
+	wm8978: codec@1a {
+		#sound-dai-cells = <0>;
+		compatible = "wlf,wm8978";
+		reg = <0x1a>;
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2s0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_mclk_pin>, <&i2s0_data_pins>;
+	status = "okay";
+};
+
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_rx_pin>;
+	status = "okay";
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-190 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <190000>;
+	};
+
+	button-390 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <390000>;
+	};
+
+	button-600 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <600000>;
+	};
+
+	button-800 {
+		label = "Search";
+		linux,code = <KEY_SEARCH>;
+		channel = <0>;
+		voltage = <800000>;
+	};
+
+	button-980 {
+		label = "Home";
+		linux,code = <KEY_HOMEPAGE>;
+		channel = <0>;
+		voltage = <980000>;
+	};
+
+	button-1180 {
+		label = "Esc";
+		linux,code = <KEY_ESC>;
+		channel = <0>;
+		voltage = <1180000>;
+	};
+
+	button-1400 {
+		label = "Enter";
+		linux,code = <KEY_ENTER>;
+		channel = <0>;
+		voltage = <1400000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+	status = "okay";
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
+
+	/* MLC Support sucks for now */
+	status = "disabled";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+	regulator-always-on;
+};
+
+&reg_dcdc3 {
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-sys";
+	regulator-always-on;
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "avcc";
+	regulator-always-on;
+};
+
+&reg_usb1_vbus {
+	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&rtp {
+	allwinner,ts-attached;
+};
+
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pin>;
+	status = "okay";
+};
+
+&tve0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	/*
+	 * The GR8-EVB has a somewhat interesting design. There's a
+	 * pin supposed to control VBUS, an ID pin, a VBUS detect pin,
+	 * so everything should work just fine.
+	 *
+	 * Except that the pin supposed to control VBUS is not
+	 * connected to any controllable output, neither to the SoC
+	 * through a GPIO or to the PMIC, and it is pulled down,
+	 * meaning that we will never be able to enable VBUS on this
+	 * board.
+	 */
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};

arch/arm/dts/sun5i-gr8.dtsi

@@ -54,7 +54,7 @@
 		allwinner,pipelines = <&fe0>;
 	};
 
-	soc@1c00000 {
+	soc {
 		pwm: pwm@1c20e00 {
 			compatible = "allwinner,sun5i-a10s-pwm";
 			reg = <0x01c20e00 0xc>;
@@ -98,28 +98,28 @@
 &pio {
 	compatible = "nextthing,gr8-pinctrl";
 
-	i2s0_data_pins_a: i2s0-data@0 {
+	i2s0_data_pins: i2s0-data-pins {
 		pins = "PB6", "PB7", "PB8", "PB9";
 		function = "i2s0";
 	};
 
-	i2s0_mclk_pins_a: i2s0-mclk@0 {
+	i2s0_mclk_pin: i2s0-mclk-pin {
 		pins = "PB5";
 		function = "i2s0";
 	};
 
-	pwm1_pins: pwm1 {
+	pwm1_pins: pwm1-pin {
 		pins = "PG13";
 		function = "pwm1";
 	};
 
-	spdif_tx_pins_a: spdif@0 {
+	spdif_tx_pin: spdif-tx-pin {
 		pins = "PB10";
 		function = "spdif";
 		bias-pull-up;
 	};
 
-	uart1_cts_rts_pins_a: uart1-cts-rts@0 {
+	uart1_cts_rts_pins: uart1-cts-rts-pins {
 		pins = "PG5", "PG6";
 		function = "uart1";
 	};

arch/arm/dts/sun5i-r8-chip.dts

@@ -79,16 +79,12 @@
 
 	mmc0_pwrseq: mmc0_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&chip_wifi_reg_on_pin>;
 		reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
 	};
 
 	onewire {
 		compatible = "w1-gpio";
-		gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
-		pinctrl-names = "default";
-		pinctrl-0 = <&chip_w1_pin>;
+		gpios = <&pio 3 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PD2 */
 	};
 };
 
@@ -109,8 +105,6 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
 
 	axp209: pmic@34 {
@@ -137,14 +131,10 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "disabled";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 
 	xio: gpio@38 {
@@ -161,13 +151,11 @@
 	};
 };
 
-&mmc0_pins_a {
+&mmc0_pins {
 	bias-pull-up;
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&mmc0_pwrseq>;
 	bus-width = <4>;
@@ -183,29 +171,6 @@
 	status = "okay";
 };
 
-&pio {
-	chip_vbus_pin: chip_vbus_pin@0 {
-		pins = "PB10";
-		function = "gpio_out";
-	};
-
-	chip_wifi_reg_on_pin: chip_wifi_reg_on_pin@0 {
-	        pins = "PC19";
-	        function = "gpio_out";
-	};
-
-	chip_id_det_pin: chip_id_det_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-	};
-
-	chip_w1_pin: chip_w1_pin@0 {
-		pins = "PD2";
-		function = "gpio_in";
-	        bias-pull-up;
-	};
-};
-
 &reg_dcdc2 {
 	regulator-min-microvolt = <1000000>;
 	regulator-max-microvolt = <1400000>;
@@ -260,7 +225,6 @@
 };
 
 &reg_usb0_vbus {
-	pinctrl-0 = <&chip_vbus_pin>;
 	vin-supply = <&reg_vcc5v0>;
 	gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
 	status = "okay";
@@ -268,7 +232,7 @@
 
 &spi2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
+	pinctrl-0 = <&spi2_pe_pins>;
 	status = "disabled";
 };
 
@@ -282,14 +246,14 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
 &uart3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_a>,
-		    <&uart3_cts_rts_pins_a>;
+	pinctrl-0 = <&uart3_pg_pins>,
+		    <&uart3_cts_rts_pg_pins>;
 	status = "okay";
 };
 
@@ -303,11 +267,9 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&chip_id_det_pin>;
 	status = "okay";
 
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_vcc5v0>;

arch/arm/dts/sun5i-reference-design-tablet.dtsi

@@ -54,7 +54,8 @@
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
-		/* TODO: backlight uses axp gpio1 as enable pin */
+		enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; /* AXP GPIO1 */
+		power-supply = <&reg_vcc3v0>;
 	};
 
 	chosen {
@@ -63,8 +64,6 @@
 };
 
 &codec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&codec_pa_pin>;
 	allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
 	status = "okay";
 };
@@ -92,11 +91,10 @@
 	 */
 	clock-frequency = <400000>;
 
-	touchscreen: touchscreen {
+	touchscreen: touchscreen@40 {
+		reg = <0x40>;
 		interrupt-parent = <&pio>;
 		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_power_pin>;
 		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
 		/* Tablet dts must provide reg and compatible */
 		status = "disabled";
@@ -124,7 +122,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -135,43 +133,6 @@
 	status = "okay";
 };
 
-&pio {
-	codec_pa_pin: codec_pa_pin@0 {
-		pins = "PG10";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	ts_power_pin: ts_power_pin {
-		pins = "PB3";
-		function = "gpio_out";
-		drive-strength = <10>;
-		bias-disable;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_pin_a: usb0_vbus_pin@0 {
-		pins = "PG12";
-		function = "gpio_out";
-	};
-};
-
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
@@ -210,7 +171,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -224,10 +185,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_ldo3>;

arch/arm/dts/sun5i.dtsi

@@ -42,14 +42,14 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "skeleton.dtsi"
-
 #include <dt-bindings/clock/sun5i-ccu.h>
 #include <dt-bindings/dma/sun4i-a10.h>
 #include <dt-bindings/reset/sun5i-ccu.h>
 
 / {
 	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
 
 	cpus {
 		#address-cells = <1>;
@@ -68,7 +68,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		framebuffer@0 {
+		framebuffer-lcd0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
@@ -77,7 +77,7 @@
 			status = "disabled";
 		};
 
-		framebuffer@1 {
+		framebuffer-lcd0-tve0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-tve0";
@@ -93,14 +93,14 @@
 		#size-cells = <1>;
 		ranges;
 
-		osc24M: clk@1c20050 {
+		osc24M: clk-24M {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
 			clock-output-names = "osc24M";
 		};
 
-		osc32k: clk@0 {
+		osc32k: clk-32k {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
@@ -108,14 +108,30 @@
 		};
 	};
 
-	soc@1c00000 {
-		compatible = "simple-bus";
+	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
-		sram-controller@1c00000 {
-			compatible = "allwinner,sun4i-a10-sram-controller";
+		/* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+		default-pool {
+			compatible = "shared-dma-pool";
+			size = <0x6000000>;
+			alloc-ranges = <0x40000000 0x10000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		dma-ranges;
+		ranges;
+
+		system-control@1c00000 {
+			compatible = "allwinner,sun5i-a13-system-control";
 			reg = <0x01c00000 0x30>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -127,13 +143,14 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x00000000 0xc000>;
-			};
 
 				emac_sram: sram-section@8000 {
-				compatible = "allwinner,sun4i-a10-sram-a3-a4";
+					compatible = "allwinner,sun5i-a13-sram-a3-a4",
+						     "allwinner,sun4i-a10-sram-a3-a4";
 					reg = <0x8000 0x4000>;
 					status = "disabled";
 				};
+			};
 
 			sram_d: sram@10000 {
 				compatible = "mmio-sram";
@@ -143,11 +160,36 @@
 				ranges = <0 0x00010000 0x1000>;
 
 				otg_sram: sram-section@0 {
-					compatible = "allwinner,sun4i-a10-sram-d";
+					compatible = "allwinner,sun5i-a13-sram-d",
+						     "allwinner,sun4i-a10-sram-d";
 					reg = <0x0000 0x1000>;
 					status = "disabled";
 				};
 			};
+
+			sram_c: sram@1d00000 {
+				compatible = "mmio-sram";
+				reg = <0x01d00000 0xd0000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x01d00000 0xd0000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun5i-a13-sram-c1",
+						     "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x80000>;
+				};
+			};
+		};
+
+		mbus: dram-controller@1c01000 {
+			compatible = "allwinner,sun5i-a13-mbus";
+			reg = <0x01c01000 0x1000>;
+			clocks = <&ccu CLK_MBUS>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			dma-ranges = <0x00000000 0x40000000 0x20000000>;
+			#interconnect-cells = <1>;
 		};
 
 		dma: dma-controller@1c02000 {
@@ -158,7 +200,7 @@
 			#dma-cells = <2>;
 		};
 
-		nfc: nand@1c03000 {
+		nfc: nand-controller@1c03000 {
 			compatible = "allwinner,sun4i-a10-nand";
 			reg = <0x01c03000 0x1000>;
 			interrupts = <37>;
@@ -207,11 +249,8 @@
 			status = "disabled";
 
 			port {
-				#address-cells = <1>;
-				#size-cells = <0>;
 
-				tve0_in_tcon0: endpoint@0 {
-					reg = <0>;
+				tve0_in_tcon0: endpoint {
 					remote-endpoint = <&tcon0_out_tve0>;
 				};
 			};
@@ -238,6 +277,7 @@
 			compatible = "allwinner,sun5i-a13-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <44>;
+			dmas = <&dma SUN4I_DMA_DEDICATED 14>;
 			resets = <&ccu RST_LCD>;
 			reset-names = "lcd";
 			clocks = <&ccu CLK_AHB_LCD>,
@@ -247,6 +287,7 @@
 				      "tcon-ch0",
 				      "tcon-ch1";
 			clock-output-names = "tcon-pixel-clock";
+			#clock-cells = <0>;
 			status = "disabled";
 
 			ports {
@@ -254,12 +295,9 @@
 				#size-cells = <0>;
 
 				tcon0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					tcon0_in_be0: endpoint@0 {
-						reg = <0>;
+					tcon0_in_be0: endpoint {
 						remote-endpoint = <&be0_out_tcon0>;
 					};
 				};
@@ -278,12 +316,25 @@
 			};
 		};
 
+		video-codec@1c0e000 {
+			compatible = "allwinner,sun5i-a13-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_VE>;
+			interrupts = <53>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun5i-a13-mmc";
 			reg = <0x01c0f000 0x1000>;
 			clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
 			clock-names = "ahb", "mmc";
 			interrupts = <32>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -321,13 +372,14 @@
 			phy-names = "usb";
 			extcon = <&usbphy 0>;
 			allwinner,sram = <&otg_sram 1>;
+			dr_mode = "otg";
 			status = "disabled";
 		};
 
 		usbphy: phy@1c13400 {
 			#phy-cells = <1>;
 			compatible = "allwinner,sun5i-a13-usb-phy";
-			reg = <0x01c13400 0x10 0x01c14800 0x4>;
+			reg = <0x01c13400 0x10>, <0x01c14800 0x4>;
 			reg-names = "phy_ctrl", "pmu1";
 			clocks = <&ccu CLK_USB_PHY0>;
 			clock-names = "usb_phy";
@@ -404,7 +456,7 @@
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
-			emac_pins_a: emac0@0 {
+			emac_pd_pins: emac-pd-pins {
 				pins = "PD6", "PD7", "PD10",
 				       "PD11", "PD12", "PD13", "PD14",
 				       "PD15", "PD18", "PD19", "PD20",
@@ -413,27 +465,27 @@
 				function = "emac";
 			};
 
-			i2c0_pins_a: i2c0@0 {
+			i2c0_pins: i2c0-pins {
 				pins = "PB0", "PB1";
 				function = "i2c0";
 			};
 
-			i2c1_pins_a: i2c1@0 {
+			i2c1_pins: i2c1-pins {
 				pins = "PB15", "PB16";
 				function = "i2c1";
 			};
 
-			i2c2_pins_a: i2c2@0 {
+			i2c2_pins: i2c2-pins {
 				pins = "PB17", "PB18";
 				function = "i2c2";
 			};
 
-			ir0_rx_pins_a: ir0@0 {
+			ir0_rx_pin: ir0-rx-pin {
 				pins = "PB4";
 				function = "ir0";
 			};
 
-			lcd_rgb565_pins: lcd_rgb565@0 {
+			lcd_rgb565_pins: lcd-rgb565-pins {
 				pins = "PD3", "PD4", "PD5", "PD6", "PD7",
 						 "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
 						 "PD19", "PD20", "PD21", "PD22", "PD23",
@@ -441,7 +493,7 @@
 				function = "lcd0";
 			};
 
-			lcd_rgb666_pins: lcd_rgb666@0 {
+			lcd_rgb666_pins: lcd-rgb666-pins {
 				pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
 				       "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
 				       "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
@@ -449,7 +501,7 @@
 				function = "lcd0";
 			};
 
-			mmc0_pins_a: mmc0@0 {
+			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2", "PF3",
 				       "PF4", "PF5";
 				function = "mmc0";
@@ -457,7 +509,15 @@
 				bias-pull-up;
 			};
 
-			mmc2_pins_a: mmc2@0 {
+			mmc2_4bit_pc_pins: mmc2-4bit-pc-pins {
+				pins = "PC6", "PC7", "PC8", "PC9",
+				       "PC10", "PC11";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_8bit_pins: mmc2-8bit-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 				       "PC10", "PC11", "PC12", "PC13",
 				       "PC14", "PC15";
@@ -466,15 +526,7 @@
 				bias-pull-up;
 			};
 
-			mmc2_4bit_pins_a: mmc2-4bit@0 {
-				pins = "PC6", "PC7", "PC8", "PC9",
-				       "PC10", "PC11";
-				function = "mmc2";
-				drive-strength = <30>;
-				bias-pull-up;
-			};
-
-			nand_pins_a: nand-base0@0 {
+			nand_pins: nand-pins {
 				pins = "PC0", "PC1", "PC2",
 				       "PC5", "PC8", "PC9", "PC10",
 				       "PC11", "PC12", "PC13", "PC14",
@@ -482,72 +534,79 @@
 				function = "nand0";
 			};
 
-			nand_cs0_pins_a: nand-cs@0 {
+			nand_cs0_pin: nand-cs0-pin {
 				pins = "PC4";
 				function = "nand0";
 			};
 
-			nand_rb0_pins_a: nand-rb@0 {
+			nand_rb0_pin: nand-rb0-pin {
 				pins = "PC6";
 				function = "nand0";
 			};
 
-			spi2_pins_a: spi2@0 {
+			pwm0_pin: pwm0-pin {
+				pins = "PB2";
+				function = "pwm";
+			};
+
+			spi2_pe_pins: spi2-pe-pins {
 				pins = "PE1", "PE2", "PE3";
 				function = "spi2";
 			};
 
-			spi2_cs0_pins_a: spi2-cs0@0 {
+			spi2_cs0_pe_pin: spi2-cs0-pe-pin {
 				pins = "PE0";
 				function = "spi2";
 			};
 
-			uart1_pins_a: uart1@0 {
+			uart1_pe_pins: uart1-pe-pins {
 				pins = "PE10", "PE11";
 				function = "uart1";
 			};
 
-			uart1_pins_b: uart1@1 {
+			uart1_pg_pins: uart1-pg-pins {
 				pins = "PG3", "PG4";
 				function = "uart1";
 			};
 
-			uart2_pins_a: uart2@0 {
+			uart2_pd_pins: uart2-pd-pins {
 				pins = "PD2", "PD3";
 				function = "uart2";
 			};
 
-			uart2_cts_rts_pins_a: uart2-cts-rts@0 {
+			uart2_cts_rts_pd_pins: uart2-cts-rts-pd-pins {
 				pins = "PD4", "PD5";
 				function = "uart2";
 			};
 
-			uart3_pins_a: uart3@0 {
+			uart3_pg_pins: uart3-pg-pins {
 				pins = "PG9", "PG10";
 				function = "uart3";
 			};
 
-			uart3_cts_rts_pins_a: uart3-cts-rts@0 {
+			uart3_cts_rts_pg_pins: uart3-cts-rts-pg-pins {
 				pins = "PG11", "PG12";
 				function = "uart3";
 			};
-
-			pwm0_pins: pwm0 {
-				pins = "PB2";
-				function = "pwm";
-			};
 		};
 
 		timer@1c20c00 {
 			compatible = "allwinner,sun4i-a10-timer";
 			reg = <0x01c20c00 0x90>;
-			interrupts = <22>;
+			interrupts = <22>,
+				     <23>,
+				     <24>,
+				     <25>,
+				     <67>,
+				     <68>;
 			clocks = <&ccu CLK_HOSC>;
 		};
 
 		wdt: watchdog@1c20c90 {
 			compatible = "allwinner,sun4i-a10-wdt";
 			reg = <0x01c20c90 0x10>;
+			interrupts = <24>;
+			clocks = <&osc24M>;
 		};
 
 		ir0: ir@1c21800 {
@@ -636,6 +695,8 @@
 			reg = <0x01c2ac00 0x400>;
 			interrupts = <7>;
 			clocks = <&ccu CLK_APB1_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -646,6 +707,8 @@
 			reg = <0x01c2b000 0x400>;
 			interrupts = <8>;
 			clocks = <&ccu CLK_APB1_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -656,11 +719,25 @@
 			reg = <0x01c2b400 0x400>;
 			interrupts = <9>;
 			clocks = <&ccu CLK_APB1_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
+		mali: gpu@1c40000 {
+			compatible = "allwinner,sun4i-a10-mali", "arm,mali-400";
+			reg = <0x01c40000 0x10000>;
+			interrupts = <69>, <70>, <71>, <72>,  <73>;
+			interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pmu";
+			clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_GPU>;
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <320000000>;
+		};
+
 		timer@1c60000 {
 			compatible = "allwinner,sun5i-a13-hstimer";
 			reg = <0x01c60000 0x1000>;
@@ -677,6 +754,8 @@
 			clock-names = "ahb", "mod",
 				      "ram";
 			resets = <&ccu RST_DE_FE>;
+			interconnects = <&mbus 19>;
+			interconnect-names = "dma-mem";
 			status = "disabled";
 
 			ports {
@@ -684,12 +763,9 @@
 				#size-cells = <0>;
 
 				fe0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					fe0_out_be0: endpoint@0 {
-						reg = <0>;
+					fe0_out_be0: endpoint {
 						remote-endpoint = <&be0_in_fe0>;
 					};
 				};
@@ -705,33 +781,26 @@
 			clock-names = "ahb", "mod",
 				      "ram";
 			resets = <&ccu RST_DE_BE>;
+			interconnects = <&mbus 18>;
+			interconnect-names = "dma-mem";
 			status = "disabled";
 
-			assigned-clocks = <&ccu CLK_DE_BE>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
 				be0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					be0_in_fe0: endpoint@0 {
-						reg = <0>;
+					be0_in_fe0: endpoint {
 						remote-endpoint = <&fe0_out_be0>;
 					};
 				};
 
 				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					be0_out_tcon0: endpoint@0 {
-						reg = <0>;
+					be0_out_tcon0: endpoint {
 						remote-endpoint = <&tcon0_in_be0>;
 					};
 				};

arch/arm/dts/sun6i-a31-app4-evb1.dts

@@ -65,22 +65,14 @@
 	status = "okay";
 };
 
-&pio {
-	usb1_vbus_pin_a: usb1_vbus_pin@0 {
-		pins = "PH27";
-		function = "gpio_out";
-	};
-};
-
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_a>;
 	gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31-colombus.dts

@@ -60,13 +60,11 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	i2c_lcd: i2c@0 {
+	i2c_lcd: i2c {
 		/* The lcd panel i2c interface is hooked up via gpios */
 		compatible = "i2c-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_lcd_pins>;
-		gpios = <&pio 0 23 GPIO_ACTIVE_HIGH>, /* PA23, sda */
-			<&pio 0 24 GPIO_ACTIVE_HIGH>; /* PA24, scl */
+		sda-gpios = <&pio 0 23 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA23 */
+		scl-gpios = <&pio 0 24 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA24 */
 		i2c-gpio,delay-us = <5>;
 	};
 };
@@ -77,31 +75,21 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_rgmii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii";
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "fail";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 
 	mma8452: mma8452@1d {
@@ -112,48 +100,27 @@
 	};
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
 	status = "okay";
 };
 
-&mmc0_pins_a {
-	bias-pull-up;
-};
-
-&pio {
-	mmc0_cd_pin_colombus: mmc0_cd_pin@0 {
-		pins = "PA8";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb2_vbus_pin_colombus: usb2_vbus_pin@0 {
-		pins = "PH24";
-		function = "gpio_out";
-	};
-
-	i2c_lcd_pins: i2c_lcd_pin@0 {
-		pins = "PA23", "PA24";
-		function = "gpio_out";
-		bias-pull-up;
-	};
-};
-
 &reg_usb2_vbus {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_vbus_pin_colombus>;
 	gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31-hummingbird.dts

@@ -86,31 +86,23 @@
 	vga-dac {
 		compatible = "dumb-vga-dac";
 		vdd-supply = <&reg_vga_3v3>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
 			port@0 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				reg = <0>;
 
-				vga_dac_in: endpoint@0 {
-					reg = <0>;
+				vga_dac_in: endpoint {
 					remote-endpoint = <&tcon0_out_vga>;
 				};
 			};
 
 			port@1 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				reg = <1>;
 
-				vga_dac_out: endpoint@0 {
-					reg = <0>;
+				vga_dac_out: endpoint {
 					remote-endpoint = <&vga_con_in>;
 				};
 			};
@@ -160,17 +152,10 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_hummingbird>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
-	snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -184,21 +169,15 @@
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	/* pull-ups and devices require AXP221 DLDO3 */
 	status = "failed";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 
 	pcf8563: rtc@51 {
@@ -209,27 +188,27 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
 	status = "okay";
 };
 
-&mmc0_pins_a {
-	/* external pull-ups missing for some pins */
-	bias-pull-up;
-};
-
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>;
 	vmmc-supply = <&reg_aldo1>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
@@ -241,31 +220,13 @@
 	status = "okay";
 };
 
-&pio {
-	gmac_phy_reset_pin_hummingbird: gmac_phy_reset_pin@0 {
-		pins = "PA21";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
-		pins = "PA8";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	wifi_reset_pin_hummingbird: wifi_reset_pin@0 {
-		pins = "PG10";
-		function = "gpio_out";
-	};
-};
-
 &p2wi {
 	status = "okay";
 
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;
 	};
@@ -354,7 +315,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 
@@ -368,8 +329,8 @@
 };
 
 &usbphy {
-	usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
-	usb0_vbus_det-gpio = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+	usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+	usb0_vbus_det-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;

arch/arm/dts/sun6i-a31-i7.dts

@@ -71,10 +71,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_i7>;
 
-		blue {
+		led {
 			label = "i7:blue:usr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 		};
@@ -118,14 +116,10 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -140,48 +134,31 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_i7>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
 	status = "okay";
 };
 
-&pio {
-	led_pins_i7: led_pins@0 {
-		pins = "PH13";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_i7: mmc0_cd_pin@0 {
-		pins = "PH22";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb1_vbus_pin_i7: usb1_vbus_pin@0 {
-		pins = "PC27";
-		function = "gpio_out";
-	};
-};
-
 &reg_usb1_vbus {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_vbus_pin_i7>;
 	gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &spdif {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spdif_pins_a>;
-	spdif-out = "okay";
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 
@@ -191,7 +168,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31-m9.dts

@@ -60,10 +60,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_m9>;
 
-		blue {
+		led {
 			label = "m9:blue:pwr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -85,26 +83,26 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	phy-supply = <&reg_dldo1>;
 	status = "okay";
+};
 
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&s_ir_rx_pin>;
+	status = "okay";
+};
+
+&mdio {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
@@ -117,31 +115,13 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
 #include "axp22x.dtsi"
 
-&pio {
-	led_pins_m9: led_pins@0 {
-		pins = "PH13";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_m9: mmc0_cd_pin@0 {
-		pins = "PH22";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb1_vbus_pin_m9: usb1_vbus_pin@0 {
-		pins = "PC27";
-		function = "gpio_out";
-	};
-};
-
 &reg_aldo1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
@@ -215,15 +195,13 @@
 };
 
 &reg_usb1_vbus {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_vbus_pin_m9>;
 	gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts

@@ -60,10 +60,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_m9>;
 
-		blue {
+		led {
 			label = "a1000g:blue:pwr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -85,26 +83,26 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	phy-supply = <&reg_dldo1>;
 	status = "okay";
+};
 
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&s_ir_rx_pin>;
+	status = "okay";
+};
+
+&mdio {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
@@ -117,31 +115,13 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
 #include "axp22x.dtsi"
 
-&pio {
-	led_pins_m9: led_pins@0 {
-		pins = "PH13";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_m9: mmc0_cd_pin@0 {
-		pins = "PH22";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb1_vbus_pin_m9: usb1_vbus_pin@0 {
-		pins = "PC27";
-		function = "gpio_out";
-	};
-};
-
 &reg_aldo1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
@@ -215,15 +195,13 @@
 };
 
 &reg_usb1_vbus {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_vbus_pin_m9>;
 	gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31-mixtile-loftq.dts

@@ -6,6 +6,9 @@
  */
 
 /dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
 #include "sun6i-a31.dtsi"
 
 / {
@@ -19,6 +22,15 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+	};
 };
 
 &ehci0 {
@@ -31,11 +43,13 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_rgmii_a>;
+	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy = <&phy1>;
 	phy-mode = "rgmii";
 	status = "okay";
+};
 
+&mdio {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
@@ -51,6 +65,11 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };

arch/arm/dts/sun6i-a31.dtsi

@@ -42,8 +42,6 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "skeleton.dtsi"
-
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -52,6 +50,8 @@
 
 / {
 	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
 
 	aliases {
 		ethernet0 = &gmac;
@@ -62,7 +62,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		simplefb_hdmi: framebuffer@0 {
+		simplefb_hdmi: framebuffer-lcd0-hdmi {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
@@ -73,7 +73,7 @@
 			status = "disabled";
 		};
 
-		simplefb_lcd: framebuffer@1 {
+		simplefb_lcd: framebuffer-lcd0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
@@ -105,37 +105,63 @@
 			reg = <0>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000	1200000
-				864000	1200000
-				720000	1100000
-				480000	1000000
-				>;
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&ccu CLK_CPU>;
+			clock-latency = <244144>; /* 8 32k periods */
+			operating-points =
+				/* kHz	  uV */
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&ccu CLK_CPU>;
+			clock-latency = <244144>; /* 8 32k periods */
+			operating-points =
+				/* kHz	  uV */
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&ccu CLK_CPU>;
+			clock-latency = <244144>; /* 8 32k periods */
+			operating-points =
+				/* kHz	  uV */
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
+			#cooling-cells = <2>;
 		};
 	};
 
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -144,7 +170,10 @@
 			cooling-maps {
 				map0 {
 					trip = <&cpu_alert0>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
 			};
 
@@ -166,12 +195,8 @@
 		};
 	};
 
-	memory {
-		reg = <0x40000000 0x80000000>;
-	};
-
 	pmu {
-		compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
+		compatible = "arm,cortex-a7-pmu";
 		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
@@ -183,17 +208,20 @@
 		#size-cells = <1>;
 		ranges;
 
-		osc24M: osc24M {
+		osc24M: clk-24M {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
+			clock-accuracy = <50000>;
+			clock-output-names = "osc24M";
 		};
 
-		osc32k: clk@0 {
+		osc32k: clk-32k {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
-			clock-output-names = "osc32k";
+			clock-accuracy = <50000>;
+			clock-output-names = "ext_osc32k";
 		};
 
 		/*
@@ -205,14 +233,14 @@
 		 * The actual TX clock rate is not controlled by the
 		 * gmac_tx clock.
 		 */
-		mii_phy_tx_clk: clk@1 {
+		mii_phy_tx_clk: clk-mii-phy-tx {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <25000000>;
 			clock-output-names = "mii_phy_tx";
 		};
 
-		gmac_int_tx_clk: clk@2 {
+		gmac_int_tx_clk: clk-gmac-int-tx {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <125000000>;
@@ -234,7 +262,7 @@
 		status = "disabled";
 	};
 
-	soc@1c00000 {
+	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -253,15 +281,21 @@
 			compatible = "allwinner,sun6i-a31-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&ccu RST_AHB1_LCD0>;
-			reset-names = "lcd";
+			dmas = <&dma 11>;
+			resets = <&ccu RST_AHB1_LCD0>,
+				 <&ccu RST_AHB1_LVDS>;
+			reset-names = "lcd",
+				      "lvds";
 			clocks = <&ccu CLK_AHB1_LCD0>,
 				 <&ccu CLK_LCD0_CH0>,
-				 <&ccu CLK_LCD0_CH1>;
+				 <&ccu CLK_LCD0_CH1>,
+				 <&ccu 15>;
 			clock-names = "ahb",
 				      "tcon-ch0",
-				      "tcon-ch1";
+				      "tcon-ch1",
+				      "lvds-alt";
 			clock-output-names = "tcon0-pixel-clock";
+			#clock-cells = <0>;
 
 			ports {
 				#address-cells = <1>;
@@ -301,15 +335,20 @@
 			compatible = "allwinner,sun6i-a31-tcon";
 			reg = <0x01c0d000 0x1000>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&ccu RST_AHB1_LCD1>;
-			reset-names = "lcd";
+			dmas = <&dma 12>;
+			resets = <&ccu RST_AHB1_LCD1>,
+				 <&ccu RST_AHB1_LVDS>;
+			reset-names = "lcd", "lvds";
 			clocks = <&ccu CLK_AHB1_LCD1>,
 				 <&ccu CLK_LCD1_CH0>,
-				 <&ccu CLK_LCD1_CH1>;
+				 <&ccu CLK_LCD1_CH1>,
+				 <&ccu 15>;
 			clock-names = "ahb",
 				      "tcon-ch0",
-				      "tcon-ch1";
+				      "tcon-ch1",
+				      "lvds-alt";
 			clock-output-names = "tcon1-pixel-clock";
+			#clock-cells = <0>;
 
 			ports {
 				#address-cells = <1>;
@@ -359,6 +398,8 @@
 			resets = <&ccu RST_AHB1_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -378,6 +419,8 @@
 			resets = <&ccu RST_AHB1_MMC1>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -431,7 +474,6 @@
 				 <&ccu CLK_PLL_VIDEO1_2X>;
 			clock-names = "ahb", "mod", "ddc", "pll-0", "pll-1";
 			resets = <&ccu RST_AHB1_HDMI>;
-			reset-names = "ahb";
 			dma-names = "ddc-tx", "ddc-rx", "audio-tx";
 			dmas = <&dma 13>, <&dma 13>, <&dma 14>;
 			status = "disabled";
@@ -457,8 +499,6 @@
 				};
 
 				hdmi_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 				};
 			};
@@ -474,6 +514,7 @@
 			phys = <&usbphy 0>;
 			phy-names = "usb";
 			extcon = <&usbphy 0>;
+			dr_mode = "otg";
 			status = "disabled";
 		};
 
@@ -557,7 +598,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun6i-a31-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&osc32k>;
+			clocks = <&osc24M>, <&rtc 0>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -570,14 +611,14 @@
 				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
-			gmac_pins_gmii_a: gmac_gmii@0 {
+			gmac_gmii_pins: gmac-gmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 						"PA4", "PA5", "PA6", "PA7",
 						"PA8", "PA9", "PA10", "PA11",
@@ -593,7 +634,7 @@
 				drive-strength = <30>;
 			};
 
-			gmac_pins_mii_a: gmac_mii@0 {
+			gmac_mii_pins: gmac-mii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 						"PA8", "PA9", "PA11",
 						"PA12", "PA13", "PA14", "PA19",
@@ -602,7 +643,7 @@
 				function = "gmac";
 			};
 
-			gmac_pins_rgmii_a: gmac_rgmii@0 {
+			gmac_rgmii_pins: gmac-rgmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 						"PA9", "PA10", "PA11",
 						"PA12", "PA13", "PA14", "PA19",
@@ -615,22 +656,22 @@
 				drive-strength = <40>;
 			};
 
-			i2c0_pins_a: i2c0@0 {
+			i2c0_pins: i2c0-pins {
 				pins = "PH14", "PH15";
 				function = "i2c0";
 			};
 
-			i2c1_pins_a: i2c1@0 {
+			i2c1_pins: i2c1-pins {
 				pins = "PH16", "PH17";
 				function = "i2c1";
 			};
 
-			i2c2_pins_a: i2c2@0 {
+			i2c2_pins: i2c2-pins {
 				pins = "PH18", "PH19";
 				function = "i2c2";
 			};
 
-			lcd0_rgb888_pins: lcd0_rgb888 {
+			lcd0_rgb888_pins: lcd0-rgb888-pins {
 				pins = "PD0", "PD1", "PD2", "PD3",
 						 "PD4", "PD5", "PD6", "PD7",
 						 "PD8", "PD9", "PD10", "PD11",
@@ -641,7 +682,7 @@
 				function = "lcd0";
 			};
 
-			mmc0_pins_a: mmc0@0 {
+			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2",
 						 "PF3", "PF4", "PF5";
 				function = "mmc0";
@@ -649,7 +690,7 @@
 				bias-pull-up;
 			};
 
-			mmc1_pins_a: mmc1@0 {
+			mmc1_pins: mmc1-pins {
 				pins = "PG0", "PG1", "PG2", "PG3",
 						 "PG4", "PG5";
 				function = "mmc1";
@@ -657,7 +698,7 @@
 				bias-pull-up;
 			};
 
-			mmc2_pins_a: mmc2@0 {
+			mmc2_4bit_pins: mmc2-4bit-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 						 "PC10", "PC11";
 				function = "mmc2";
@@ -665,7 +706,7 @@
 				bias-pull-up;
 			};
 
-			mmc2_8bit_emmc_pins: mmc2@1 {
+			mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 						 "PC10", "PC11", "PC12",
 						 "PC13", "PC14", "PC15",
@@ -675,7 +716,7 @@
 				bias-pull-up;
 			};
 
-			mmc3_8bit_emmc_pins: mmc3@1 {
+			mmc3_8bit_emmc_pins: mmc3-8bit-emmc-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 						 "PC10", "PC11", "PC12",
 						 "PC13", "PC14", "PC15",
@@ -685,12 +726,12 @@
 				bias-pull-up;
 			};
 
-			spdif_pins_a: spdif@0 {
+			spdif_tx_pin: spdif-tx-pin {
 				pins = "PH28";
 				function = "spdif";
 			};
 
-			uart0_pins_a: uart0@0 {
+			uart0_ph_pins: uart0-ph-pins {
 				pins = "PH20", "PH21";
 				function = "uart0";
 			};
@@ -703,13 +744,16 @@
 				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&osc24M>;
 		};
 
 		wdt1: watchdog@1c20ca0 {
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		spdif: spdif@1c21000 {
@@ -849,6 +893,8 @@
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C0>;
 			resets = <&ccu RST_APB2_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -860,6 +906,8 @@
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C1>;
 			resets = <&ccu RST_APB2_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -871,6 +919,8 @@
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C2>;
 			resets = <&ccu RST_APB2_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -900,9 +950,13 @@
 			snps,fixed-burst;
 			snps,force_sf_dma_mode;
 			status = "disabled";
+
+			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
 				#address-cells = <1>;
 				#size-cells = <0>;
 			};
+		};
 
 		crypto: crypto-engine@1c15000 {
 			compatible = "allwinner,sun6i-a31-crypto",
@@ -950,6 +1004,8 @@
 			dma-names = "rx", "tx";
 			resets = <&ccu RST_AHB1_SPI0>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		spi1: spi@1c69000 {
@@ -962,6 +1018,8 @@
 			dma-names = "rx", "tx";
 			resets = <&ccu RST_AHB1_SPI1>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		spi2: spi@1c6a000 {
@@ -974,6 +1032,8 @@
 			dma-names = "rx", "tx";
 			resets = <&ccu RST_AHB1_SPI2>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		spi3: spi@1c6b000 {
@@ -986,10 +1046,12 @@
 			dma-names = "rx", "tx";
 			resets = <&ccu RST_AHB1_SPI3>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		gic: interrupt-controller@1c81000 {
-			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
 			      <0x01c82000 0x2000>,
 			      <0x01c84000 0x2000>,
@@ -1073,9 +1135,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_BE1>;
 
-			assigned-clocks = <&ccu CLK_BE1>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1119,9 +1178,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_DRC1>;
 
-			assigned-clocks = <&ccu CLK_IEP_DRC1>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1165,9 +1221,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_BE0>;
 
-			assigned-clocks = <&ccu CLK_BE0>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1189,12 +1242,9 @@
 				};
 
 				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					be0_out_drc0: endpoint@0 {
-						reg = <0>;
+					be0_out_drc0: endpoint {
 						remote-endpoint = <&drc0_in_be0>;
 					};
 				};
@@ -1211,20 +1261,14 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_DRC0>;
 
-			assigned-clocks = <&ccu CLK_IEP_DRC0>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
 				drc0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					drc0_in_be0: endpoint@0 {
-						reg = <0>;
+					drc0_in_be0: endpoint {
 						remote-endpoint = <&be0_out_drc0>;
 					};
 				};
@@ -1248,13 +1292,16 @@
 		};
 
 		rtc: rtc@1f00000 {
+			#clock-cells = <1>;
 			compatible = "allwinner,sun6i-a31-rtc";
 			reg = <0x01f00000 0x54>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc32k>;
+			clock-output-names = "osc32k";
 		};
 
-		nmi_intc: interrupt-controller@1f00c00 {
+		r_intc: interrupt-controller@1f00c00 {
 			compatible = "allwinner,sun6i-a31-r-intc";
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -1269,7 +1316,7 @@
 			ar100: ar100_clk {
 				compatible = "allwinner,sun6i-a31-ar100-clk";
 				#clock-cells = <0>;
-				clocks = <&osc32k>, <&osc24M>,
+				clocks = <&rtc 0>, <&osc24M>,
 					 <&ccu CLK_PLL_PERIPH>,
 					 <&ccu CLK_PLL_PERIPH>;
 				clock-output-names = "ar100";
@@ -1304,7 +1351,7 @@
 			ir_clk: ir_clk {
 				#clock-cells = <0>;
 				compatible = "allwinner,sun4i-a10-mod0-clk";
-				clocks = <&osc32k>, <&osc24M>;
+				clocks = <&rtc 0>, <&osc24M>;
 				clock-output-names = "ir";
 			};
 
@@ -1320,7 +1367,7 @@
 		};
 
 		ir: ir@1f02000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			clocks = <&apb0_gates 1>, <&ir_clk>;
 			clock-names = "apb", "ir";
 			resets = <&apb0_rst 1>;
@@ -1334,21 +1381,20 @@
 			reg = <0x01f02c00 0x400>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
 			clock-names = "apb", "hosc", "losc";
 			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			#size-cells = <0>;
 			#gpio-cells = <3>;
 
-			ir_pins_a: ir@0 {
+			s_ir_rx_pin: s-ir-rx-pin {
 				pins = "PL4";
 				function = "s_ir";
 			};
 
-			p2wi_pins: p2wi {
+			s_p2wi_pins: s-p2wi-pins {
 				pins = "PL0", "PL1";
 				function = "s_p2wi";
 			};
@@ -1362,7 +1408,7 @@
 			clock-frequency = <100000>;
 			resets = <&apb0_rst 3>;
 			pinctrl-names = "default";
-			pinctrl-0 = <&p2wi_pins>;
+			pinctrl-0 = <&s_p2wi_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts

@@ -53,7 +53,7 @@
 	vref-supply = <&reg_aldo3>;
 	status = "okay";
 
-	button@1000 {
+	button-1000 {
 		label = "Home";
 		linux,code = <KEY_HOMEPAGE>;
 		channel = <0>;

arch/arm/dts/sun6i-a31s-cs908.dts

@@ -66,28 +66,31 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	status = "okay";
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &ohci1 {
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31s-inet-q972.dts

@@ -54,8 +54,6 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 
 	ft5406ee8: touchscreen@38 {
@@ -73,21 +71,21 @@
 	vref-supply = <&reg_aldo3>;
 	status = "okay";
 
-	button@200 {
+	button-200 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
 		voltage = <200000>;
 	};
 
-	button@900 {
+	button-900 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <900000>;
 	};
 
-	button@1200 {
+	button-1200 {
 		label = "Back";
 		linux,code = <KEY_BACK>;
 		channel = <0>;

arch/arm/dts/sun6i-a31s-primo81.dts

@@ -90,19 +90,13 @@
 
 &i2c0 {
 	/* pull-ups and device VDDIO use AXP221 DLDO3 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
 	status = "failed";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 
 	ctp@5d {
-		pinctrl-names = "default";
-		pinctrl-0 = <&gt911_int_primo81>;
 		compatible = "goodix,gt911";
 		reg = <0x5d>;
 		interrupt-parent = <&pio>;
@@ -112,8 +106,6 @@
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 
 	accelerometer@1c {
@@ -123,7 +115,6 @@
 		reg = <0x1c>;
 		interrupt-parent = <&pio>;
 		interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */
-		#io-channel-cells = <1>;
 	};
 };
 
@@ -131,14 +122,14 @@
 	vref-supply = <&reg_aldo3>;
 	status = "okay";
 
-	button@158 {
+	button-158 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <158730>;
 	};
 
-	button@349 {
+	button-349 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
@@ -147,8 +138,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
@@ -156,22 +145,11 @@
 };
 
 &pio {
-	gt911_int_primo81: gt911_int_pin@0 {
-		pins = "PA3";
-		function = "gpio_in";
-	};
-
-	mma8452_int_primo81: mma8452_int_pin@0 {
+	mma8452_int_primo81: mma8452-int-pin {
 		pins = "PA9";
 		function = "gpio_in";
 		bias-pull-up;
 	};
-
-	mmc0_cd_pin_primo81: mmc0_cd_pin@0 {
-		pins = "PA8";
-		function = "gpio_in";
-		bias-pull-up;
-	};
 };
 
 &p2wi {
@@ -180,7 +158,7 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;
 	};
@@ -281,7 +259,7 @@
 };
 
 &usbphy {
-	usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+	usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_dldo1>;

arch/arm/dts/sun6i-a31s-sina31s-core.dtsi

@@ -78,7 +78,7 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
@@ -135,7 +135,7 @@
 /* UART0 pads available on core board */
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31s-sina31s.dts

@@ -66,8 +66,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_sina31s>;
 
 		status {
 			label = "sina31s:status:usr";
@@ -116,15 +114,11 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	phy-supply = <&reg_dldo1>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -139,7 +133,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -147,14 +141,14 @@
 	vref-supply = <&reg_aldo3>;
 	status = "okay";
 
-	button@158 {
+	button-158 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <158730>;
 	};
 
-	button@349 {
+	button-349 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
@@ -162,9 +156,13 @@
 	};
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina31s>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
@@ -175,19 +173,6 @@
 	status = "okay";
 };
 
-&pio {
-	led_pin_sina31s: led_pin@0 {
-		pins = "PH13";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_sina31s: mmc0_cd_pin@0 {
-		pins = "PA4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &reg_dldo1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
@@ -196,7 +181,7 @@
 
 &spdif {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spdif_pins_a>;
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 

arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts

@@ -58,20 +58,18 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_bpi_m2>;
 
-		blue {
+		led-0 {
 			label = "bpi-m2:blue:usr";
 			gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
 		};
 
-		green {
+		led-1 {
 			label = "bpi-m2:green:usr";
 			gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
 		};
 
-		red {
+		led-2 {
 			label = "bpi-m2:red:usr";
 			gpios = <&pio 6 5 GPIO_ACTIVE_HIGH>; /* PG5 */
 		};
@@ -79,8 +77,6 @@
 
 	mmc2_pwrseq: mmc2_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mmc2_pwrseq_pin_bpi_m2>;
 		reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */
 	};
 };
@@ -95,42 +91,38 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii";
 	phy-supply = <&reg_dldo1>;
-	snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>; /* PA21 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
 	status = "okay";
 };
 
-&mmc0_pins_a {
-	bias-pull-up;
-};
-
 &mmc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_a>;
+	pinctrl-0 = <&mmc2_4bit_pins>;
 	vmmc-supply = <&reg_aldo1>;
 	mmc-pwrseq = <&mmc2_pwrseq>;
 	bus-width = <4>;
@@ -146,10 +138,6 @@
 	};
 };
 
-&mmc2_pins_a {
-	bias-pull-up;
-};
-
 &ohci0 {
 	status = "okay";
 };
@@ -160,38 +148,13 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
 	};
 };
 
-&pio {
-	gmac_phy_reset_pin_bpi_m2: gmac_phy_reset_pin@0 {
-		pins = "PA21";
-		function = "gpio_out";
-	};
-
-	led_pins_bpi_m2: led_pins@0 {
-		pins = "PG5", "PG10", "PG11";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_bpi_m2: mmc0_cd_pin@0 {
-		pins = "PA4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
-&r_pio {
-	mmc2_pwrseq_pin_bpi_m2: mmc2_pwrseq_pin@0 {
-		pins = "PL8";
-		function = "gpio_out";
-	};
-};
-
 #include "axp22x.dtsi"
 
 &reg_aldo1 {
@@ -291,10 +254,81 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 
 &usbphy {
 	status = "okay";
 };
+
+&pio {
+	gpio-line-names =
+		/* PA */
+		"ETXD0", "ETXD1", "ETXD2", "ETXD3", "SDC0-DET", "", "",
+		"", "ETXCLK", "ETXEN", "EGTXCLK", "ERXD0", "ERXD1",
+		"ERXD2", "ERXD3", "", "", "", "", "ERXDV", "ERXCK",
+		"ETXERR", "ERXERR", "ECOL", "ECRS", "ECLKIN", "EMDC",
+		"EMDIO", "", "", "", "",
+
+		/* PB */
+		"CN7-P29", "CN7-P31", "CN7-P33", "CN7-P35", "CN7-P37",
+		"CN7-P28", "CN7-P27", "CN7-P32", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "",
+
+		/* PC */
+		"", "", "", "", "", "", "WL-SDIO-CMD", "WL-SDIO-CLK",
+		"WL-SDIO-D0", "WL-SDIO-D2", "WL-SDIO-D2", "WL-SDIO-D3",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "USB-DRV", "", "", "", "",
+
+		/* PD */
+		"CN9-P09", "CN9-P11", "CN9-P13", "CN9-P15", "CN9-P17",
+		"CN9-P19", "CN9-P21", "CN9-P23", "CN9-P25", "CN9-P27",
+		"CN9-P29", "CN9-P31", "CN9-P33", "CN9-P35", "CN9-P37",
+		"CN9-P39", "CN9-P40", "CN9-P38", "CN9-P36", "CN9-P34",
+		"CN9-P32", "CN9-P30", "CN9-P28", "CN9-P26", "CN9-P22",
+		"CN9-P14", "CN9-P18", "CN9-P16", "", "", "", "",
+
+		/* PE */
+		"CN6-P20", "CN6-P24", "CN6-P30", "CN6-P28", "CN7-P08",
+		"CN7-P10", "CN7-P36", "CN7-P38", "CN6-P17", "CN6-P19",
+		"CN6-P21", "CN6-P23", "CN6-P25", "CN6-P27", "CN6-P29",
+		"CN6-P31", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "",
+
+		/* PF */
+		"SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
+		"SDC0-D2", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"",
+
+		/* PG */
+		"CN9-P06", "CN9-P08", "CN9-P20", "CN9-P12", "CN9-P07",
+		"LED-PWR", "CN7-P13", "CN7-P11", "CN7-P22", "CN7-P15",
+		"LED-G", "LED-B", "CN7-P26", "CN7-P24", "CN7-P23",
+		"CN7-P19", "CN7-P21", "HCEC", "CN6-P22", "", "", "", "",
+		"", "", "", "", "", "", "", "", "",
+
+		/* PH */
+		"", "", "", "", "", "", "", "", "", "CN7-P07",
+		"CN7-P12", "CN7-P16", "CN7-P18", "CN9-P10", "CN6-P16",
+		"CN6-P14", "CN9-P04", "CN9-P02", "CN7-P05", "CN7-P03",
+		"CN8-P03", "CN8-P02", "", "", "CN6-P34", "CN6-P32",
+		"CN6-P26", "CN6-P18", "", "", "", "";
+};
+
+&r_pio {
+	gpio-line-names =
+		/* PL */
+		"PMU-SCK", "PMU-SDA", "VBAT-EN", "", "IR-RX",
+		"WL-WAKE-HOST", "BT-WAKE_HOST", "BT-ENABLE",
+		"WL-PMU-EN", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "",
+
+		/* PM */
+		"CN6-P12", "CN6-P35", "CN7-P40", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "";
+};

arch/arm/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts

@@ -62,14 +62,10 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
 };
 
@@ -89,34 +85,20 @@
 	status = "okay";
 };
 
-&pio {
-	mmc0_cd_pin_bs1078v2: mmc0_cd_pin@0 {
-		pins = "PA8";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bs1078v2>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
 	status = "okay";
 };
 
-&mmc0_pins_a {
-	bias-pull-up;
-};
-
 &p2wi {
 	status = "okay";
 
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
@@ -189,11 +171,12 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 
 &usbphy {
+	usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
 	usb1_vbus-supply = <&reg_dldo1>;
 	usb2_vbus-supply = <&reg_dc1sw>;
 	status = "okay";

arch/arm/dts/sun6i-reference-design-tablet.dtsi

@@ -66,34 +66,20 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
 	status = "okay";
 };
 
-&pio {
-	mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
-		pins = "PA8";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PA15";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &p2wi {
 	status = "okay";
 
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		drivevbus-supply = <&reg_vcc5v0>;
 		x-powers,drive-vbus-en;
@@ -179,9 +165,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+	usb0_id_det-gpios = <&pio 0 15 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA15 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_dldo1>;

arch/arm/dts/sun7i-a20-bananapi-m1-plus.dts

@@ -74,12 +74,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "bananapi-m1-plus:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-1 {
 			label = "bananapi-m1-plus:pwr:usr";
 			gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -129,14 +129,10 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -171,6 +167,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;

arch/arm/dts/sun7i-a20-bananapi.dts

@@ -77,7 +77,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "bananapi:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
@@ -104,16 +104,15 @@
 
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
-	operating-points = <
+	operating-points =
 		/* kHz	  uV */
-		960000	1400000
-		912000	1400000
-		864000	1350000
-		720000	1250000
-		528000	1150000
-		312000	1100000
-		144000	1050000
-		>;
+		<960000	1400000>,
+		<912000	1400000>,
+		<864000	1350000>,
+		<720000	1250000>,
+		<528000	1150000>,
+		<312000	1100000>,
+		<144000	1050000>;
 };
 
 &de {
@@ -131,14 +130,10 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -171,6 +166,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
@@ -246,12 +247,6 @@
 			"SPI-MISO", "SPI-CE1", "",
 		"IO-6", "IO-3", "IO-2", "IO-0", "", "", "", "",
 		"", "", "", "", "", "", "", "";
-
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
 };
 
 #include "axp209.dtsi"
@@ -329,9 +324,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;

arch/arm/dts/sun7i-a20-bananapro.dts

@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "bananapro:blue:usr";
 			gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-1 {
 			label = "bananapro:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
@@ -109,14 +109,10 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &i2c0 {
@@ -143,6 +139,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;

arch/arm/dts/sun7i-a20-cubieboard2.dts

@@ -75,12 +75,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "cubieboard2:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-1 {
 			label = "cubieboard2:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
@@ -115,13 +115,9 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_mii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -161,6 +157,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &ohci0 {
 	status = "okay";
 };
@@ -173,14 +175,6 @@
 	status = "okay";
 };
 
-&pio {
-	usb0_id_detect_pin: usb0-id-detect-pin {
-		pins = "PH4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &reg_ahci_5v {
 	status = "okay";
 };
@@ -236,9 +230,7 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>;
-	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

arch/arm/dts/sun7i-a20-cubietruck.dts

@@ -75,22 +75,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "cubietruck:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		orange {
+		led-1 {
 			label = "cubietruck:orange:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		white {
+		led-2 {
 			label = "cubietruck:white:usr";
 			gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-3 {
 			label = "cubietruck:green:usr";
 			gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -150,13 +150,9 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &hdmi {
@@ -194,6 +190,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;

arch/arm/dts/sun7i-a20-haoyu-marsboard.dts

@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Conley Lee
+ * Conley Lee <conleylee@foxmail.com>
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "HAOYU Electronics Marsboard A20";
+	compatible = "haoyu,a20-marsboard", "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
+	phy-handle = <&phy0>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	gmac_txerr: gmac-txerr-pin {
+		pins = "PA17";
+		function = "gmac";
+	};
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1450000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};

arch/arm/dts/sun7i-a20-hummingbird.dts

@@ -100,19 +100,10 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "rgmii";
 	phy-supply = <&reg_gmac_vdd>;
-	/* phy reset config */
-	snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
-	snps,reset-active-low;
-	/* wait 1s after reset, otherwise fail to read phy id */
-	snps,reset-delays-us = <0 10000 1000000>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &i2c0 {
@@ -146,6 +137,16 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		reset-gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+		reset-assert-us = <10000>;
+		/* wait 1s after reset, otherwise fail to read phy id */
+		reset-deassert-us = <1000000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;

arch/arm/dts/sun7i-a20-i12-tvbox.dts

@@ -62,12 +62,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-0 {
 			label = "i12_tvbox:red:usr";
 			gpios = <&pio 7 9 GPIO_ACTIVE_LOW>;
 		};
 
-		blue {
+		led-1 {
 			label = "i12_tvbox:blue:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
@@ -115,14 +115,10 @@
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_mii_pins>;
-	phy = <&phy1>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &i2c0 {
@@ -145,6 +141,12 @@
 	status = "okay";
 };
 
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;