- Reworks Qualcomm support to be more generic, dropping board specific
build targets and relying on DT as the only source of truth
- Switches all Qualcomm devices to use upstream devicetree
When U-Boot as running as the first stage bootloader on MSM8916 devices,
early debug UART requires turning on the clocks (for some reason the
pre-loader turns them off?!).
To simplify developing for this platform, allow the
apq8016_clk_init_uart() function to be called externally. Developers can
call this from the serial_msm debug uart driver to configure the clocks
before the driver model is available.
As it is only possible to enable early debug UART in custom builds of
U-Boot, this solution at least gives developers the option.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Don't use hardcoded clock IDs, use the IDs from the dt-bindings to be
compatible with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
On the DB410c we support running as a first stage bootloader. This
requires initialising the GPIOs which are muxed to UART before they can
be used. Add DM_FLAG_PRE_RELOC to the apq8016 pinctrl driver to ensure
that we do this early enough.
This is required to prevent the first few lines of UART log from being
dropped.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Upstream devicetrees label GPIOs with "gpioX", not "GPIO_X", fix this
for SoCs where we're now using upstream DT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Most platforms have a handful of "special" GPIOs, like the MMC
clock/data lanes, UFS reset, etc. These don't follow the usual naming
scheme of "gpioX" and also have unique capabilities and registers. We
can get away without supporting them all for now, but DT compatibility
is still an issue.
Add support for allowing these to be specified after the other pins, and
make all pinmux/pinconf calls for them nop.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Introduce a basic pinctrl driver for the SPMI PMIC GPIOs. This is
necessary to make proper use of upstream DT bindings specifically on the
dragonboard410c where they're used to switch between USB host and device
modes.
Only support for driving the pins as output low or high is enabled for
now.
To minimise duplicated code and allow for sharing common DT data, the
pinctrl driver is initialised as a child of the existing GPIO driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Some platforms hard reset when attempting to configure PMIC GPIOs. Add
support for quirks specified in match data with a single quirk to skip
this configuration. We rely on the GPIO already be configured correctly,
which is always the case for volume up (the only current user of these
GPIOs).
This is not expected behaviour but appears to be due to a U-Boot
specific bug. This quirk at least allows for the volume buttons to be
used on platforms where this bug is apparent.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the modern helpers to fetch the clock and use the correct property
("clocks" instead of "clock"). Drop the call to pinctrl_select_state()
as no boards have a "uart" pinctrl state and this prints confusing
errors.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Introduce support for early debugging. This relies on the previous stage
bootloader to initialise the UART clocks, when running with U-Boot as
the primary bootloader this feature doesn't work. It will require a way
to configure the clocks before the driver model is available.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We should be returning the rate that we set the clock to, drivers like
MMC rely on this. So fix it.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust the apq8016 and apq8096 drivers to use the upstream compatible
properties, and adjust the associated dts files in U-Boot.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the clk_* helper functions and the correct property name for clocks.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for a vbus-supply regulator specified in devicetree. This
provides generic support to avoid hardcoded GPIO configuration in board
init code.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
SPL is cleaning bss after calling board_init_f. Setting up console is done
and little_endian global variable is cleared which caused that console
stops to work. That's why move it to data seciton now. The patch should be
reverted when bss is cleared before board_init_f is called.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/934dc8871c59265eb9d8012193aa97d9b8bd7f33.1707911544.git.michal.simek@amd.com
Roger Quadros <rogerq@kernel.org> says:
MUX driver should autoprobe if the device tree has "idle-states"
property. Drop using the custom "u-boot,mux-autoprobe" property
in TI device trees.
Some platforms need the MUX state to be auto initialized at
boot time even if there are no explicit users for the MUX.
In these cases, the MUX device tree has "idle-states" property
which specifies what state the MUX should be initialized to.
So far we were relying on custom u-boot property "u-boot,mux-autoprobe"
to autoprobe such MUXes. This patch causes the MUX to autoprobe
if it has "idle-states" property in device tree.
This should allow us to stop using the custom "u-boot,mux-autoprobe"
property.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
If SYSRESET support is enabled for the RAA215300 PMIC, we need to bind
the raa215300_sysreset driver as a child device of the PMIC.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This patch adds support for resetting a board via the RAA215300 PMIC.
Note that the RAA215300 documentation names the available reset types
differently to u-boot:
* A "warm" reset via the RAA215300 PMIC will fully reset the SoC
(CPU & GPIOs), so this corresponds to SYSRESET_COLD.
* A "cold" reset via the RAA215300 PMIC will cycle all power supply
rails, so this corresponds to SYSRESET_POWER.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/G2L SMARC module is powered via a Renesas RAA215300 PMIC which
provides several voltage converters, a real time clock (RTC) and reset
control. A basic driver is implemented for this device so that we can
read, write and dump the PMIC registers.
The raa215300_bind() function is added as a stub, binding of the
sysreset driver will be added in a later patch.
Additional features of this PMIC (such as reset control) may be
supported by future patches.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver supports the I2C module on the Renesas RZ/G2L (R9A07G044)
SoC, also known as the RIIC module.
This patch is based on both the u-boot driver in the Renesas RZ BSP
3.0.5 release [1] (commit 7fcc1fdc2534), and the Linux v6.7 driver
(commit 0dd3ee311255).
Support for deblocking the I2C bus is included as this may be needed
after triggering a reset via the Power Management IC (PMIC) over I2C
(the PMIC asserts the reset line before the SoC completes the I2C write
transaction with obvious bus locking effects). If the SDA line is
observed to be low during initialisation, we automatically attempt to
deblock.
[1]: https://github.com/renesas-rz/renesas-u-boot-cip
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When enabling/disabling a clock or reset signal, confirm that the change
has completed before returning from the function. A somewhat arbitrary
100ms timeout is defined to ensure that the system doesn't lock up in
the case of an error.
Since we need to dynamically determine if we're waiting for a 0 bit or a
1 bit, it's easier to use wait_for_bit_32() than readl_poll_timeout().
This change is needed for reliable initialization of the I2C driver
which is added in a following patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
i.MX93 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To prepare support for multiple register layouts pointers to register
tables where added to struct cpg_mssr_info. These pointers are suppose
to be filled in at probe time and no intended change in behavior was
intended.
However the new pointers where only filled in by some paths of the
driver implemented in clk-rcar-gen3.c. The path implemented in
clk-rcar-gen2.c was not updated leaving the pointers uninitialized
leading to a crash when trying to probe the clocks.
Fix this by filling in the pointers in the Gen2 code path with the
values used before they where moved to struct cpg_mssr_info.
Fixes: d413214fb748 ("clk: renesas: Add register pointers into struct cpg_mssr_info")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R8A7791 Porter
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This message isn't an error (there can be a watchdog subnode for example)
but it shouldn't be printed unless this driver is being debugged. Demote
it to a debug print.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
AM64 ES2.0 bootrom seems to enable WAIT0EDGEDETECTION interrupt.
This causes a lockup at A53 SPL when accessing NAND controller
or ELM registers.
A good option would be to softrest GPMC block at probe
but this cannot be done for AM64 as SOFTRESET bit is marked
as reserved in SYSCONFIG register.
Fix the issue by disabling all IRQs at probe.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
ID code is added for zu67dr_SE, zu11eg_SE, zu19eg_SE and zu47dr_SE
variants. SE is the select edition of restricted devices with the
capabilities.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240123045715.893652-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Recent i.MX8MP DTs use new fsl,imx6ul-ecspi compatible string instead
of the fsl,imx51-ecspi compatible string. Add the new compatible string
to fix ECSPI operation on i.MX8MP.
For details, see Linux:
48d74376fb68 ("arm64: dts: imx8mp: update ecspi compatible and clk")
8eb1252bbedf ("spi: imx: remove ERR009165 workaround on i.mx6ul")
Fixes: 451799a6ceac ("arm: dts: imx8mp: Sync the DT with kernel 6.4-rc4")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Support RPC SPI on R8A779H0 V4M SoC.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
